Under certain rare conditions, I2C_STAT[13].RDR bit may be set
and the corresponding interrupt fire, even there is no data in
the receive FIFO, or the I2C data transfer is still ongoing.
These spurious RDR events must be ignored by the software.

This patch handles and ignores RDR spurious interrupts.

The below sequence is required in interrupt handler for
handling this errata:
1. If RDR is set to 1, clear RDR
2. Read I2C status register and check for BusBusy bit. If BusBusy
bit is set, skip remaining steps.
3. If BusBusy bit is not set, perform read operation on I2C status
register.
4. If RDR is set, clear the same. Check RDR again and clear if it sets
RDR bit again.
5. Perform I2C Data Read operation N number of times(where N is value
read from the register BUFSTAT-RXSTAT bit fields).

Note:
This errata is not applicable for omap2420 and omap4.
It is applicable for:
1. omap2430
2. omap34xx(including omap3630).
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Cc: Hema Kalliguddi <hemahk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The errata 1.153 workaround is busy waiting on XUDF bit in interrupt
context, which may lead to kernel hangs. The problem can be reproduced
by running the bus with wrong (too high) speed.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This is to avoid insanely long lines and levels of indentation.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Cc: Nishant Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.

Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.

Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.

Updates by Kevin as requested by Tony:

- Remove omap_set_i2c_constraint_func() in favor of conditionally
  adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
  conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
  OMAP PM function can be used directly in pdata.

Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch is rebased version of earlier post to add I2C
driver support to OMAP4 platform. On OMAP4, all
I2C register address offsets are changed from OMAP1/2/3 I2C.
In order to not have #ifdef's at various places in code,
as well as to support multi-OMAP build, an array is created
to hold the register addresses with it's offset.

This patch was submitted, reviewed and acked on mailing list
already. For more details refer below link
http://www.mail-archive.com/linux-i2c@vger.kernel.org/msg02281.html

This updated verion has a depedancy on "Add support for 16-bit registers"
posted on linux-omap. Below is the patch-works link for the same

http://patchwork.kernel.org/patch/72295/Signed-off-by: NSyed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

A smbus quick transfer has no data after the address byte.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

i2c event of next read/write byte may trigger before current int state
is cleared in the interrupt handler. So, this should be done at the
beginning of interrupt handler to avoid losing new i2c events.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add some debug() code to decode the error register.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

There isn't much point in managing our own custom timeout timer when the
completion interface already includes support for it.  This makes the
resulting code much simpler and robust.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The S3C I2C controller indicates completion of I2C transfers before
the bus has a stop condition on it. In order to ensure that we do not
attempt to start a new transfer before the bus is idle the driver
currently inserts a 1ms delay. This is vastly larger than is generally
required and has a visible effect on performance under load, such as
when bringing up audio CODECs or reading back status information with
non-bulk I2C reads.

Replace the sleep with a spin on the IIC status register for up to 1ms.
This will busy wait but testing on my SMDK6410 system indicates that
the overwhelming majority of transactions complete on the first spin,
with maximum latencies of less than 10 spins so the absolute overhead
of busy waiting should be at worst comprable to msleep(), and the
overall system performance is dramatically improved.

The main risk is poor interaction with multimaster systems where
we may miss the bus going idle before the next transaction. Defend
against this by falling back to the original 1ms delay after 20 spins.

The overall effect in my testing is an approximately 20% improvement
in kernel startup time.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This reverts commit 9c0a342c because
it was included without proper signoffs from RTC maintainers.

Make the driver depend on either ARCH_S3C2410 (as legacy) or the new
device selection of SAMSUNG_DEV_TS.

Change the menuconfig name to reflect this driver is now handling more
devices that just the s3c2410.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDmitry Torokhov <dtor@mail.ru>

This patch adds a feature bit field in the touchscreen driver for Samsung SoCs.
Which can be used to distinguish the TSADC module features.
Signed-off-by: NNaveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor fix to title]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDmitry Torokhov <dtor@mail.ru>

This patch implements generic GPIO configuration function in Samsung
touchscreen driver. And makes the touchscreen driver s3c24xx-ts.c
generic to all the Samsung SoCs.
Signed-off-by: NNaveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: fixed title ]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDmitry Torokhov <dtor@mail.ru>

This moves mach-s3c2410/include/mach/ts.h to plat-samsung/include/plat/ts.h in
order to prepare for s3c64xx support in the touchscreen driver.
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove unnecessary Kconfig entry. S5PC100 has exactly the same driver as
S3C6400/S3C6410/S5P6440.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Add Amiga Zorro bus modalias and uevent support
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Make the platform resource input parameters of platform_device_add_resources()
and platform_device_register_simple() const, as the resources are copied and
never modified.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

commits 638157bc ("serial167: prepare to push
BKL down into drivers") and 4165fe4e ("tty:
Fix up char drivers request_room usage") removed code without removing the
corresponding variables:

| drivers/char/serial167.c: In function 'cd2401_rx_interrupt':
| drivers/char/serial167.c:630: warning: unused variable 'len'
| drivers/char/serial167.c: In function 'cy_ioctl':
| drivers/char/serial167.c:1531: warning: unused variable 'val'

Remove the variables to kill the warnings.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Use kmemdup when some other buffer is immediately copied into the
allocated region.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
statement S;
@@

-  to = \(kmalloc\|kzalloc\)(size,flag);
+  to = kmemdup(from,size,flag);
   if (to==NULL || ...) S
-  memcpy(to, from, size);
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use kstrdup when the goal of an allocation is copy a string into the
allocated region.  Additionally drop the now unused variable len.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@

-  to = kmalloc(strlen(from) + 1,flag);
+  to = kstrdup(from, flag);
   ... when != \(from = E1 \| to = E1 \)
   if (to==NULL || ...) S
   ... when != \(from = E2 \| to = E2 \)
-  strcpy(to, from);
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove qdio API wrappers used by qeth and replace them by calling the
appropriate functions directly.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The state change indicator is bit 7 not bit 0 of the dsci. Use the
correct bit for setting the indicator.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Don't convert timestamps to microseconds, use timestamps returned by
get_clock() directly.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove memset hack that relied on the layout of struct qdio_q
to avoid deletion of the slib pointer.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If adapter interrupts are not available and traditional IO interrupts
are used for qdio the inbound tasklet continued to run if new data
arrived. That could possibly block other tasklets scheduled on the
same CPU. If new data arrives schedule the tasklet again instead of
directly processing the new data.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add missing increment for the qdio interrupt counter.
Signed-off-by: NSigned-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove the duplicate of the DASD uid from the devmap structure.
Use the uid from the device private structure instead.
This also removes a lockdep warning complaining about a possible
SOFTIRQ-safe -> SOFTIRQ-unsafe lock order.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

For base Parallel Access Volume (PAV) there is a fixed mapping of
base and alias devices. With dynamic PAV this mapping can be changed
so that an alias device is used with another base device.
This patch enables the DASD device driver to tolerate dynamic PAV
changes.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use nonseekable_open for a couple of s390 device drivers. This avoids
the use of default_llseek function which has a dependency on the BKL.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Change the tristate Kbuild option into a bool option so that the module
is either builtin or not available at all.
There have been too many cases where people were missing the 'vmcp'
device node and unable to send z/VM CP commands. So let's make sure
that on distros it will always be present.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

A machine check can interrupt the i/o and external interrupt handler
anytime. If the machine check occurs while the interrupt handler is
waking up from idle vtime_start_cpu can get executed a second time
and the int_clock / async_enter_timer values in the lowcore get
clobbered. This can confuse the cpu time accounting.
To fix this problem two changes are needed. First the machine check
handler has to use its own copies of int_clock and async_enter_timer,
named mcck_clock and mcck_enter_timer. Second the nested execution
of vtime_start_cpu has to be prevented. This is done in s390_idle_check
by checking the wait bit in the program status word.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove cpu_id from lowcore and replace addr_t with __u64.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

As we were using an internal dma flushing routine, this patch changes to
the DMA API flush_kernel_dcache_page().  Driver is able to compile now.

[akpm@linux-foundation.org: flush_kernel_dcache_page() comes before kunmap_atomic()]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on.  To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question.  Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD.  Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.

2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint.  Fixed.

3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one.  Noticed and fixed.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.

This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.

Signed-off-by: Valentin Longchamp<valentin.longchamp@epfl.ch>
Tested-by: Philippe Rétornaz<philippe.retornaz@epfl.ch>
Acked-by: Wolfram Sang<w.sang@pengutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>