skb->truesize is not meant to be tracking amount of used bytes
in an skb, but amount of reserved/consumed bytes in memory.

For instance, if we use a single byte in last page fragment,
we have to account the full size of the fragment.

skb->truesize can be very different from skb->len, that has
a very specific safety purpose.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Tx VLAN offloading is disabled frames with size ~ MTU are not
transmitted as the driver does not account 4 bytes of VLAN header added
by stack. It should use VLAN_ETH_HLEN instead of ETH_HLEN.

The second problem is with newer BNA chips (BNA 1860). These chips filter
out any VLAN tagged frames in Tx path. This is a problem when Tx VLAN
offloading is disabled and frames are tagged by stack. Older chips like
1010/1020 are not affected as they probably don't do such filtering.

Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device claims TSO and checksum support for vlans.  It also
allows a user to control vlan acceleration offloading.  As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information.  This results
in corrupted frames sent on the wire.

This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.

CC: Rasesh Mody <rmody@brocade.com>
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The recent commit "e29aa339 bna: Enable Multi Buffer RX" is causing
a performance regression. It does not properly update 'cmpl' pointer
at the end of the loop in NAPI handler bnad_cq_process(). The result is
only one packet / per NAPI-schedule is processed.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly scripted conversion of the smp_mb__* barriers.
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/n/tip-55dhyhocezdw1dg7u19hmh1u@git.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Rasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in bnad_start_xmit that
can be called in hard irq and other contexts.

dev_kfree_skb_any is used as bnad_start_xmit only frees skbs when to
drop them, normally transmitted packets are handled elsewhere.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent commit "fe1624cf bna: RX Filter Enhancements" disables
VLAN tag stripping if the NIC is in promiscuous mode. This causes
__vlan_hwaccel_put_tag() is called when the stripping is disabled.
Because of this VLAN over bna does not work and causes BUGs in conjunction
with openvswitch like this:
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Cc: Rasesh Mody <rmody@brocade.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use 'make namespacecheck' to code that could be declared static.
After that remove code that is not being used.

Compile tested only.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

> as reported for linux-next of Dec.20, 2013
> when CONFIG_NEED_DMA_MAP_STATE is not enabled:
>
> drivers/net/ethernet/brocade/bna/bnad.c: In function 'bnad_start_xmit':
> drivers/net/ethernet/brocade/bna/bnad.c:3074:26: error: 'struct bnad_tx_vector' has no member named 'dma_len'
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Store the length of the skb buffer mapped along with the handle and use it
   while unmapping the buffer.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - When bnad_setup_tx() returns NULL, the error is NOT returned to the caller.
   The caller will incorrectly assume success. So Return ENOMEM when bna_tx_create()
   fails.
 - If bnad_tx_msix_register() fails, call bna_tx_destroy() to free tx & to NULL
   the bnad reference to tcb.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we already check to see whether the BNAD_TXQ_TX_STARTED cleared.
But if the tcb structure which contains this flag is also already freed by that
time, we would dereference the NULL pointer. This patch is to check tcb for NULL
pointer, before dereferencing it.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Valid bit check for completion needs read fence, so that it does not get
reordered with other loads.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
 - Prefetch header in GRO path. This reduces napi_frags_skb time from 9% to 5%.
 - Changed the configurable limit of RxQ depth to 16384 (was 2048).
 - bnad_rx_unmap_q elements are cachealigned.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CT2 HW supports multi-buffer Rx. This patch provides the necessary changes
for bnad to use multi-buffer Rx feature. For BNAD, multi-buffer Rx is by
default enabled when MTU is > 4096. For >4096 MTU, q0 data/large buffers are of
2048 size. As the resource requirements of multi-buffer Rx are different new Rx
needs to be created to use this feature. ASIC posts multiple completions if
frame exceeds buffer size. The last completion is marked with EOP flag.
 - Separate HQ and DQ enums for resource allocations and configurations.
 - rx_config and rxq structure changes to pass the correct info from bnad.
 - DQ depth need not be same as HQ depth. So CQ depth is adjusted accordingly.
 - Rx CFG frame size is taken from configured MTU.
 - Rx q0 buffer size is configured from bnad s rx_config when multi-buffer is
   enabled.
 - Poll for entire frame completion.
 - Once EOP completion is received gather the number of vectors used by the
   frame to submit it to the stack.
 - Changed MTU to frame size wherever necessary.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
 - Added bna_rx_ucast_listset() for synchronous ucast listadd operation.
 - Clear mac->handle before adding it to free_q.
 - bnad_set_rx_mode() rewritten. bnad_set_rx_mode() adds the MACs in uc_list
   to UCAM. If it exceeds the max supported, DEFAULT mode is turned on. If
   MCAM limit is exceeded, ALLMULTI mode is turned on.
 - Clear CF flags, check for the new mode and reprogram the Rx approach.
 - Added bnad_set_rx_ucast_fltr() and bnad_set_rx_mcast_fltr().
 - Check for IFF_PROMISC to set the correct mode.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Invoke skb_tx_timestamp() API just before invoking txq_doorbell()
 - Add ethtool (-T) support
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile tested only.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Acked-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fallback to 32-bit DMA mask is rather odd:
	if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)) &&
	    !dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64))) {
		*using_dac = true;
	} else {
		err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
		if (err) {
			err = dma_set_coherent_mask(&pdev->dev,
						    DMA_BIT_MASK(32));
			if (err)
				goto release_regions;
		}

This means we only try and set the coherent DMA mask if we failed to
set a 32-bit DMA mask, and only if both fail do we fail the driver.
Adjust this so that if either setting fails, we fail the driver - and
thereby end up properly setting both the DMA mask and the coherent
DMA mask in the fallback case.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Driver configuration flags are retained across open/stop operations preventing
configurations to be set in next open/stop. Setting MTU on a 1020 causes
network to fail until a reboot is performed on the host.

Clear the flags when configuration resets in hardware.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the missing iounmap() before return from bnad_init()
in the error handling case.
Introduced by commit 01b54b14
(bna: tx rx cleanup fix).
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the number of calls required to alloc
a zeroed block of memory.

Trivially reduces overall object size.

Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change Details:
        Enhanced support for GRO. Page-base allocation method for Rx buffers is
used in GRO. Skb allocation has been removed in Rx path to use always warm-cache
skbs provided by napi_get_frags.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 -      Have contiguous queue pages for TxQ, RxQ and CQ. Data structure and
        QPT changes related to contiguous queue pages
 -      Optimized Tx and Rx unmap structures. Tx and Rx fast path changes due to
        unmap data structure changes
 -      Re-factored Tx and Rx fastpath routines as per the new queue data structures
 -      Implemented bnad_txq_wi_prepare() to program the opcode, flags, frame_len
        and num_vectors in the work item
 -      Reduced Max TxQ and RxQ depth to 2048 while default value for Tx/Rx queue
        depth is unaltered (512)
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 -      Remove unnecessary prefetch
 -      Simplify checking & comparison of CQ flags
 -      Dereference & store unmap_array, unmap_cons & current unmap_array
        element only once
 -      Make structures tx_config & rx_config cache line aligned.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Rasesh Mody <rmody@brocade.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

GCC can't see that in all non-error-return paths we do in fact
set *using_dac to something.

Add an explicit initialization to remove this warning:

drivers/net/ethernet/brocade/bna/bnad.c: In function ‘bnad_pci_probe’:
drivers/net/ethernet/brocade/bna/bnad.c:3079:5: warning: ‘using_dac’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/brocade/bna/bnad.c:3233:7: note: ‘using_dac’ was declared here
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert doxygen (or similar) formatted comments to kernel-doc or
unformatted comment.  Delete a few that are content-free.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

release_firmware() does its own NULL test so explicit test before call
is unneeded.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Renamed following functions:
bnad_cleanup_tx to bnad_destroy_tx
bnad_free_all_txbufs to bnad_txq_cleanup
bnad_free_txbufs to bnad_txcmpl_process
bnad_tx to bnad_tx_complete
bnad_cleanup_rx to bnad_destroy_rx
bnad_reset_rcb to bnad_rcb_cleanup
bnad_free_all_rxbufs to bnad_rxq_cleanup
bnad_cq_cmpl_init to bnad_cq_cleanup
bnad_alloc_n_post_rxbufs to bnad_rxq_post
bnad_poll_cq to bnad_cq_process
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The scheduling of tasklet and keeping the interrupts enabled makes interrupt
reduntant. 20% of the Tx interrupts have nothing left to process or could not
process as Tx tasklet was running.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>