Seems nobody else is checking/testing this case as it keeps getting
horked.

If we have no BAR4 mapping on an SFF controller this is *NOT* an error,
it just means it isn't doing BMDMA.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_tf_read was setting HOB bit when lba48 command was submitted, but
was not clearing it before reading "normal" data.  As it is only place
which sets HOB bit in control register, and register reads should not
be affected by other bits, let's just clear it when we are done with
reading upper bytes so non-48bit commands do not have to touch ctl
at all.

pata_scc suffered from same problem...
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The filename in the file header is incorrect.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

With PCI resource fix up for legacy hosts.  We can use the same code
path to allocate IO resources and initialize host for both legacy and
native SFF hosts.  Only IRQ requesting needs to be different.

Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all
legacy specific functions and use the renamed functions instead.  This
simplifies code a lot.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

host->irq and host->irq2 should be set before ata_host_register() for
IRQ reporting to work.  Move up host->irq assignment in
ata_host_activate() and add it to ata_pci_init_one() native path and
pata_cs5520.

The port info printing in ata_host_register() doesn't fit all the
different controllers.  It should probably be moved out to LLDs with
some helpers in the future.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.

In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller.  This never became actually
necessary and the related code always has been subtly broken one way
or the other.  Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases.  Exotic
cases can simply dealt within LLDs as necessary.

This patch removes port_mask handling in SFF init helpers.  SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore.  All information is carried via port_info.  n_ports argument
is dropped and always two ports are allocated.  LLD can tell SFF to
skip certain port by marking it dummy.  Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.

This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic.  The following changes
are made...

* ata_pci_init_native_host() and ata_init_legacy_host() both now try
  to initialized whatever they can and mark failed ports dummy.  They
  return 0 if any port is successfully initialized.

* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
  take n_ports argument.  All info should be specified via port_info
  array.  Always two ports are allocated.

* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.

* port_info handling in all LLDs are standardized - all port_info
  arrays are const stack variable named ppi.  Unless the second port
  is different from the first, its port_info is specified as NULL
  (tells libata that it's identical to the last non-NULL port_info).

* pata_hpt37x/hpt3x2n: don't modify static variable directly.  Make an
  on-stack copy instead as ata_piix does.

* pata_uli: It has 4 ports instead of 2.  Don't use
  ata_pci_prepare_native_host().  Allocate the host explicitly and use
  init helpers.  It's simple enough.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Marvell IDE interface on my machine would hit a BUG_ON() in
lib/iomem.c because it was calling ata_pci_init_one() specifying just a
single port on the host, but that would actually end up trying to
initialize two ports, the second one with bogus information.

This fixes "ata_pci_init_one()" so that it actually passes down the
n_ports variable that it got from the low-level driver to the host
allocation routine ("ata_host_alloc_pinfo()"), which results in the ATA
layer actually having the correct port number information.

And in order to make it all work, I also needed to fix a few places that
had incorrectly hard-coded the fact that a host always had exactly two
ports (both ata_pci_init_bmdma() and ata_request_legacy_irqs() would
just always iterate over both ports).
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

All drivers are converted to new init model.  Kill probe_ent,
ata_device_add() and ata_pci_init_native_mode().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

These will be used to convert LLDs to new init model.

* Add irq_handler field to port_info.  In new init model, requesting
  IRQ is LLD's responsibility and libata doesn't need to know about
  irq_handler.  Most LLDs can simply register their irq_handler but
  some need different irq_handler depending on specific chip.  The
  added port_info->irq_handler field can be used by LLDs to select
  the matching IRQ handler in such cases.

* Add ata_dummy_port_info.

* Implement ata_pci_prepare_native_host(), a helper to alloc ATA host,
  acquire all resources and init the host in one go.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Convert native PCI host handling to alloc-init-register model.  New
function ata_pci_init_native_host() follows the new init model and
replaces ata_pci_init_native_mode().  As there are remaining LLD
users, the old function isn't removed yet.

ata_pci_init_one() is reimplemented using the new function and now
fully converted to new init model.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Convert legacy PCI host handling to alloc-init-register model.
ata_init_legacy_host(), ata_request_legacy_irqs() and
ata_pci_init_bmdma() are separated out and follow the new init model.

The two legacy handling functions use separate ata_legacy_devres
instead of generic devm_* resources.  This reduces devres overhead for
legacy hosts which was a bit high because it didn't use PCI/iomap
merged resoruces.

ata_pci_init_one() is rewritten in terms of the aboved functions but
native mode handling is still using the old method.  Conversion will
be completed when native mode handling is updated.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Disabled port handling in ata_pci_init_native_mode() is slightly
broken in that it may end up using the wrong port_info.  This patch
updates it such that disables ports are made dummy as done in the
legacy and other cases.

While at it, fix indentation in ata_resources_present().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.

This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.

For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.

In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

With Tejun having added adev->ap some time ago we can get rid of the
almost unused port being passed to mode filters. And while we are
doing filters, lets turn on the !IORDY filter as well.
Signed-off-by: NAlan Cox <alan@redhat.com>

With some hand massaging from
Signed-off-by: NJeff Garzik <jeff@garzik.org>

No code changes.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_port has two different id fields - id and port_no.  id is
system-wide 1-based unique id for the port while port_no is 0-based
host-wide port number.  The former is primarily used to identify the
ATA port to the user in printk messages while the latter is used in
various places in libata core and LLDs to index the port inside the
host.

The two fields feel quite similar and sometimes ap->id is used in
place of ap->port_no, which is very difficult to spot.  This patch
renames ap->id to ap->print_id to reduce the possibility of such bugs.

Some printk messages are adjusted such that id string (ata%u[.%u])
isn't printed twice and/or to use ata_*_printk() instead of hardcoded
id format.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch is against the libata core and headers.

Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.

In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.

In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NAkira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Convert libata core layer and LLDs to use iomap.

* managed iomap is used.  Pointer to pcim_iomap_table() is cached at
  host->iomap and used through out LLDs.  This basically replaces
  host->mmio_base.

* if possible, pcim_iomap_regions() is used

Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update libata core layer to use devres.

* ata_device_add() acquires all resources in managed mode.

* ata_host is allocated as devres associated with ata_host_release.

* Port attached status is handled as devres associated with
  ata_host_attach_release().

* Initialization failure and host removal is handedl by releasing
  devres group.

* Except for ata_scsi_release() removal, LLD interface remains the
  same.  Some functions use hacky is_managed test to support both
  managed and unmanaged devices.  These will go away once all LLDs are
  updated to use devres.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Readability/typos etc
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

An ATA controller in native mode may have one or more channels disabled
and not assigned resources. In that case the existing code crashes trying
to access I/O ports 0-7.

Add the neccessary check.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.

This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.

There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixes bogus accesses to ports 0-15 with a non DMA capable controller.
This I think should go in for 2.6.20
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some uli controllers have stuck SIMPLEX bit which can't be cleared
with ata_pci_clear_simplex(), but the controller is capable of doing
DMAs on both channels simultaneously.  Implement ATA_FLAG_IGN_SIMPLEX
which makes libata ignore the simplex bit and use it in sata_uli.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This is a slight variant on the patch I posted December 16th to fix
libata combined mode handling. The only real change is that we now
correctly also reserve BAR1,2,4. That is basically a neatness issue.

Jeff was unhappy about two things

1. That it didn't work in the case of one channel native one channel
legacy.

This is a silly complaint because the SFF layer in libata doesn't handle
this case yet anyway.

2. The case where combined mode is in use and IDE=n.

In this case the libata quirk code reserves the resources in question
correctly already.

Once the combined mode stuff is redone properly (2.6.21) then the entire
mess turns into a single pci_request_regions() for all cases and all the
ugly resource hackery goes away.

I'm sending this now rather than after running full test suites so that
it can get the maximal testing in a short time. I'll be running tests on
this after lunch.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: NAlessandro Suardi <alessandro.suardi@gmail.com>
Acked-by: NTheodore Tso <tytso@mit.edu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Now that BMDMA status is recorded in irq handler.  ata_bmdma_freeze()
is free to manipulate host status.  Under certain circumstances, some
controllers (ICH7 in enhanced mode w/ IRQ shared) raise IRQ when CTL
register is written to and ATA_NIEN doesn't mask it.

This patch makes ata_bmdma_freeze() clear all pending IRQs after
freezing a port.  This change makes explicit clearing in
ata_device_add() unnecessary and thus kills it.  The removed code was
SFF-specific and was in the wrong place.

Note that ->freeze() handler is always called under ap->lock held and
irq disabled.  Even if CTL manipulation causes stuck IRQ, it's cleared
immediately.  This should be safe (enough) even in SMP environment.
More correct solution is to mask the IRQ from IRQ controller but that
would be an overkill.
Signed-off-by: NTejun Heo <htejun@gmail.com>

For certain errors, interrupt handler alter BMDMA host status before
entering EH (clears active and intr).  Thus altered BMDMA host status
value is recorded by BMDMA EH and reported to user.  Move BMDMA host
status recording from EH to interrupt handler.
Signed-off-by: NTejun Heo <htejun@gmail.com>

There are machines out there which share legacy PCI IDE IRQs w/ other
devices.  libata SFF interrupt/HSM code is ready for shared IRQ and
has been setting IRQF_SHARED for devices in native PCI mode.  Device
in legacy mode is still a PCI device and thus supposedly uses
active-low level triggered IRQ.

Machines with such setup should be quite rare and w/o this flag libata
is likely to fail loading and render the system unuseable.  Also, IDE
driver has been setting IRQF_SHARED for devices in legacy mode for a
looooong time.
Signed-off-by: NTejun Heo <htejun@gmail.com>

ata_irq_on() isn't used outside of libata core layer.  The function is
TF/SFF interface specific but currently used by core path with some
hack too.  Move it from include/linux/libata.h to
drivers/ata/libata-sff.c.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds support for ADMA mode on NVIDIA nForce4 (CK804/MCP04) SATA
controllers to the sata_nv driver.  Benefits of ADMA mode include:

- NCQ support

- Reduced CPU overhead (controller DMAs command information from memory
  instead of them being pushed in by the CPU)

- Full 64-bit DMA support

ADMA mode is enabled by default in this version.  To disable it, set the
module parameter adma_enabled=0.
Signed-off-by: NRobert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There are some Linux supported platforms that simply cannot hit the low
I/O addresses used by ATA legacy mode PCI mappings. These platforms have
a window for PCI space that is fixed by the board logic and doesn't
include the neccessary locations.

Provide a config option so that such platforms faced with a controller
that they cannot support simply error it and punt
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't write the same code twice, in two different functions, when they
both call the same initialization function, with the same private_data
pointer info.

Also, note a bug found with a FIXME.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* Replace needless 'n_ports > 2' check with a simple BUG_ON().
  No existing driver ever wants more than 2 ports.

* Delete ATA_FLAG_NO_LEGACY check.  No current driver uses
  ata_pci_init_one(), that sets this flag.

* Move PCI_CLASS_PROG register read below pci_enable_device()

* Handle ata_device_add() failure
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Non-uniform ports handling got broken while updating libata to handle
those in the same host.  Only separate irq for the non-uniform
secondary port was implemented while all other fields (host flags,
transfer mode...) of the secondary port simply shared those of the
first.

For ata_piix combined mode, which ATM is the only user of non-uniform
ports, this causes the secondary port assume the wrong type.  This can
cause PATA port to use SATA ops, which results in bogus check on PCS
and detection failure.

This patch adds ata_probe_ent->pinfo2 which points to optional
port_info for the secondary port.  For the time being, this seems to
be the simplest solution.  This workaround will be removed together
with ata_probe_ent itself after init model is updated to allow more
flexibility.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Nelson A. de Oliveira <naoliv@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

The biggest change is that ata_host_set is renamed to ata_host.

* ata_host_set			=> ata_host
* ata_probe_ent->host_flags	=> ata_probe_ent->port_flags
* ata_probe_ent->host_set_flags	=> ata_probe_ent->_host_flags
* ata_host_stats		=> ata_port_stats
* ata_port->host		=> ata_port->scsi_host
* ata_port->host_set		=> ata_port->host
* ata_port_info->host_flags	=> ata_port_info->flags
* ata_(.*)host_set(.*)\(\)	=> ata_\1host\2()

The leading underscore in ata_probe_ent->_host_flags is to avoid
reusing ->host_flags for different purpose.  Currently, the only user
of the field is libata-bmdma.c and probe_ent itself is scheduled to be
removed.

ata_port->host is reused for different purpose but this field is used
inside libata core proper and of different type.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>