Add a PCIe clock and use that instead of directly touching the clock
control register. While at it, fail if there is no such clock.
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4452Signed-off-by: NJohn Crispin <blogic@openwrt.org>

There are bcma based devices like the Linksys E2000 out there, which do
have one ieee80211 core, but no PCIe core and they are using no
prefixes for the sprom. In addition some values like boardtype are
stored without a prefix for the main SoC chip also when they have an
additional PCIe wifi chip with an own boardtype var on some devices.

The Ethernet addresses are now also read out correctly without a prefix
so calling bcm47xx_fill_sprom_ethernet is not needed any more.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4364Signed-off-by: NJohn Crispin <blogic@openwrt.org>

If there is no ieee80211 core on the devices like on the BCM4706 read
out the sprom and the other data without using a prefix.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4361Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Read out the full board data independently of the sprom version. Now we
also get the full boardflags and so on if sromrev is not set and our
code would assume a rev 1 device. When a nvram option is not set
because it is not there this is no problem.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4363Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The memory size is detected by finding a place where it repeats in
memory. Currently we are just checking when the function prom_init is
seen again, but it is better to check for a bigger part of the memory
to decrease the chance of wrong results.

This should fix a problem we saw in OpenWrt, where the detected
available memory decreed on some devices when doing a soft reboot.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4362Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Ignoring the last page when ddr size is 128M. Cached accesses to last
page is causing the processor to prefetch using address above 128M
stepping out of the ddr address space.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4365Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Commit 97ce2c88 (jump-label: initialize
jump-label subsystem much earlier) caused MIPS to break, so this was
resolved with commit 6650df3c (MIPS:
Move cache setup to setup_arch().).  Unfortunately, after this commit,
the coherency kernel parameters, cca and coherentio, are no longer
processed before their values are used.

This patch fixes this problem by marking them as early_param, which
results in them being processed before they are needed.
Signed-off-by: NShane McDonald <mcdonald.shane@gmail.com>
Acked-by: NDavid Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/3961Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The cavium code assumed that all NOR on the boot bus was
an 8-bit NOR part and hardcoded the bankwidth. The simple
solution was to add the code that queries the configuration
register for the width of the bus that has been hardware strapped
to the Cavium. This allows both 8-bit and 16-bit parts to be
discovered during boot.
Acked-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NCharles Hardin <ckhardin@exablox.com>
Patchwork: http://patchwork.linux-mips.org/patch/4323Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The new functions introduced in commit 02a54177 (MIPS: tlbex: Deal with
re-definition of label) should be marked __cpuinit, to eliminate a
warning that can pop up when CONFIG_EXPORT_UASM is disabled:

      LD      arch/mips/mm/built-in.o
    WARNING: arch/mips/mm/built-in.o(.text+0x2a4c): Section mismatch in reference from the function uasm_bgezl_hazard() to the function .cpuinit.text:uasm_il_bgezl()
    The function uasm_bgezl_hazard() references
    the function __cpuinit uasm_il_bgezl().
    This is often because uasm_bgezl_hazard lacks a __cpuinit
    annotation or the annotation of uasm_il_bgezl is wrong.

    WARNING: arch/mips/mm/built-in.o(.text+0x2a68): Section mismatch in reference from the function uasm_bgezl_label() to the function .cpuinit.text:uasm_build_label()
    The function uasm_bgezl_label() references
    the function __cpuinit uasm_build_label().
    This is often because uasm_bgezl_label lacks a __cpuinit
    annotation or the annotation of uasm_build_label is wrong.

(This warning might not occur if the function was inlined.)
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4517Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The variables here are really not used uninitialized.

arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: warning: 'offset.un' may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Just get %icc2 into the state we would have after local_irq_disable()
and physical IRQ having happened since then.  Then we can simply
use preempt_schedule_irq() and be done with the whole mess.
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The kernel_thread() changes for FRV don't work, and FRV fails to boot,
starting with:

	commit 02ce496f
	Author: Al Viro <viro@zeniv.linux.org.uk>
	Date:   Tue Sep 18 22:18:51 2012 -0400
	Subject: frv: split ret_from_fork, simplify kernel_thread() a lot

The problem is that the userspace registers are completely cleared when a
kernel thread is created and all subsequent user threads are then copied from
that.  Unfortunately, however, the TBR and PSR registers are restored from the
pt_regs and the values they should be set to are clobbered by the memset.

Instead, copy across the old user registers as normal, and then merely alter
GR8 and GR9 in it if we're going to execute a kernel thread.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Fix the preemption handling in FRV code where the PREEMPT_ACTIVE value is
incorrectly loaded into the threadinfo flags rather than the threadinfo
preemption count.

Unfortunately, the code cannot be simply converted to use
preempt_schedule_irq() as is because FRV uses virtual interrupt disablement to
cut down on the cost of actually disabling interrupts and thus
local_irq_enable() doesn't actually enable interrupts.
Reported-by: NAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: Al Viro <viro@ZenIV.linux.org.uk>

Don't let objcopy transfer the GNU build_id note into the loadable image as it
is located at address 0 and the image ends up >3G in size.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Add missing linux/export.h #inclusions to the FRV arch.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

After commit b3356bf0 (KVM: emulator: optimize "rep ins" handling),
the pieces of io data can be collected and write them to the guest memory
or MMIO together

Unfortunately, kvm splits the mmio access into 8 bytes and store them to
vcpu->mmio_fragments. If the guest uses "rep ins" to move large data, it
will cause vcpu->mmio_fragments overflow

The bug can be exposed by isapc (-M isapc):

[23154.818733] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
[ ......]
[23154.858083] Call Trace:
[23154.859874]  [<ffffffffa04f0e17>] kvm_get_cr8+0x1d/0x28 [kvm]
[23154.861677]  [<ffffffffa04fa6d4>] kvm_arch_vcpu_ioctl_run+0xcda/0xe45 [kvm]
[23154.863604]  [<ffffffffa04f5a1a>] ? kvm_arch_vcpu_load+0x17b/0x180 [kvm]

Actually, we can use one mmio_fragment to store a large mmio access then
split it when we pass the mmio-exit-info to userspace. After that, we only
need two entries to store mmio info for the cross-mmio pages access
Signed-off-by: NXiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

As Mukesh explained it, the MMUEXT_TLB_FLUSH_ALL allows the
hypervisor to do a TLB flush on all active vCPUs. If instead
we were using the generic one (which ends up being xen_flush_tlb)
we end up making the MMUEXT_TLB_FLUSH_LOCAL hypercall. But
before we make that hypercall the kernel will IPI all of the
vCPUs (even those that were asleep from the hypervisor
perspective). The end result is that we needlessly wake them
up and do a TLB flush when we can just let the hypervisor
do it correctly.

This patch gives around 50% speed improvement when migrating
idle guest's from one host to another.

Oracle-bug: 14630170

CC: stable@vger.kernel.org
Tested-by: NJingjie Jiang <jingjie.jiang@oracle.com>
Suggested-by: NMukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Use the new __HVC macro in hypercall.S.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Using the 'o' memory constraint in inline assembly can result in GCC
generating invalid immediate offsets for memory access instructions with
reduced addressing capabilities (i.e. smaller than 12-bit immediate
offsets):

  http://gcc.gnu.org/bugzilla/show_bug.cgi?id=54983

As there is no constraint to specify the exact addressing mode we need,
fallback to using 'Q' exclusively for halfword I/O accesses. This may
emit an additional add instruction (using an extra register) in order
to construct the address but it will always be accepted by GAS.
Reported-by: NBastian Hecht <hechtb@googlemail.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

After commit 846a1368 ("ARM: vfp: fix
saving d16-d31 vfp registers on v6+ kernels"), the OMAP 2430SDP board
started crashing during boot with omap2plus_defconfig:

[    3.875122] mmcblk0: mmc0:e624 SD04G 3.69 GiB
[    3.915954]  mmcblk0: p1
[    4.086639] Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
[    4.093719] Modules linked in:
[    4.096954] CPU: 0    Not tainted  (3.6.0-02232-g759e00b8 #570)
[    4.103149] PC is at vfp_reload_hw+0x1c/0x44
[    4.107666] LR is at __und_usr_fault_32+0x0/0x8

It turns out that the context save/restore fix unmasked a latent bug
in commit 5aaf2544 ("ARM: 6203/1: Make
VFPv3 usable on ARMv6").  When CONFIG_VFPv3 is set, but the kernel is
booted on a pre-VFPv3 core, the code attempts to save and restore the
d16-d31 VFP registers.  These are only present on non-D16 VFPv3+, so
this results in an undefined instruction exception.  The code didn't
crash before commit 846a1368 because the save and restore code was
only touching d0-d15, present on all VFP.

Fix by implementing a request from Russell King to add a new HWCAP
flag that affirmatively indicates the presence of the d16-d31
registers:

   http://marc.info/?l=linux-arm-kernel&m=135013547905283&w=2

and some feedback from Måns to clarify the name of the HWCAP flag.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Måns Rullgård <mans.rullgard@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The scheduler imposes a requirement to sched_clock()
which is to stop the clock during suspend, if we don't
do that any RT thread will be rescheduled in the future
which might cause any sort of problems.

This became an issue on OMAP when we converted omap-i2c.c
to use threaded IRQs, it turned out that depending on how
much time we spent on suspend, the I2C IRQ thread would
end up being rescheduled so far in the future that I2C
transfers would timeout and, because omap_hsmmc depends
on an I2C-connected device to detect if an MMC card is
inserted in the slot, our rootfs would just vanish.

arch/arm/kernel/sched_clock.c already had an optional
implementation (sched_clock_needs_suspend()) which would
handle scheduler's requirement properly, what this patch
does is simply to make that implementation non-optional.

Note that this has the side-effect that printk timings
won't reflect the actual time spent on suspend so other
methods to measure that will have to be used.

This has been tested with beagleboard XM (OMAP3630) and
pandaboard rev A3 (OMAP4430). Suspend to RAM is now working
after this patch.

Thanks to Kevin Hilman for helping out with debugging.
Acked-by: NKevin Hilman <khilman@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 92063cee, it
was applied prematurely, causing this build error for
imx_v4_v5_defconfig:

arch/arm/mach-imx/clk-imx25.c: In function 'mx25_clocks_init':
arch/arm/mach-imx/clk-imx25.c:206:26: error: 'pwm_ipg_per' undeclared (first use in this function)
arch/arm/mach-imx/clk-imx25.c:206:26: note: each undeclared identifier is reported only once for each function it appears in

Sascha Hauer explains:
> There are several gates missing in clk-imx25.c. I have a patch which
> adds support for them and I seem to have missed that the above depends
> on it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

With the introduction of CONFIG_ARCH_MULTIPLATFORM, versatile is
no longer the default platform, so we need to enable
CONFIG_ARCH_VERSATILE explicitly in order for that to be selected
rather than the multiplatform configuration.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The split of 370 and XP into two Kconfig options and the multiplatform
kernel support has changed a few Kconfig symbols, so let's update the
mvebu_defconfig file with the latest changes.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

patch 738a0fd7 "ARM: at91: fix external interrupts in non-DT case"
fixed a run-time error on some at91 platforms but did not apply
the same change to at91x40, which now doesn't build.

This changes at91x40 in the same way that the other platforms
were changed.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This reverts commit 871ae57a, which is
scheduled for v3.8 and accidently got into v3.7-rc series.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>

Commit

    844ab6f9 x86, mm: Find_early_table_space based on ranges that are actually being mapped

added back some lines back wrongly that has been removed in commit

    7b16bbf9 Revert "x86/mm: Fix the size calculation of mapping tables"

remove them again.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQW_vuaYQbmagVnxT2DGsYc=9tNeAbdBq53sYkitPOwxSQ@mail.gmail.comAcked-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

When we copy a user thread with CLONE_VM, we also have to reset
windowbase and windowstart to start a pristine stack frame. Otherwise,
overflows can happen using the address 0 as the stack pointer.
Also add a special case for vfork, which continues on the
parent stack until it calls execve. Because this could be a call8, we
need to spill the stack pointer of the previus frame (if still 'live' in
the register file).
Signed-off-by: NChris Zankel <chris@zankel.net>

Define virt_to_bus and bus_to_virt as virt_to_phys, and phys_to_virt,
       respectively.
Signed-off-by: NChris Zankel <chris@zankel.net>

Xtensa implements a method that allows to generate a arbitrary output
for each system call by defining the __SYSCALL(number, function, num_args).
This usually requires to include uapi/unistd.h twice. Instead of removing
the guard agains multiple inclusion entirely, allow to include unistd.h again
only if __SYSCALL is defined. Note that __SYSCALL gets always undefined at
the end of the file.
Signed-off-by: NChris Zankel <chris@zankel.net>

When 32-bit EFI is used with 64-bit kernel (or vice versa), turn off
efi_enabled once setup is done. Beyond setup, it is normally used to
determine if runtime services are available and we will have none.

This will resolve issues stemming from efivars modprobe panicking on a
32/64-bit setup, as well as some reboot issues on similar setups.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45991Reported-by: NMarko Kohtala <marko.kohtala@gmail.com>
Reported-by: NMaxim Kammerer <mk@dee.su>
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@kernel.org # 3.4 - 3.6
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>

This fixes early_printk() compilation for
socfpga. (senduart/busyuart/waituart were missing). It does that by
making Picochip code generic.
Signed-off-by: NPavel Machek <pavel@denx.de>
Acked-by: NDinh Nguyen <dinguyen@altera.com>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Few empty files (spear1310_misc_regs.h and spear1340_misc_regs.h) are created by
commit b31e2372 "SPEAr13xx: Add header files".

Don't know how they got added, obviously my fault :)
But nobody could even catch them in reviews.

Remove them.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The current DT nodes for mx23/mx28 miss the `clocks-names` item for gpmi-nand.
So the gpmi-nand driver could not find the proper clock.

This patch fixes this issue.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Here we fix a simple copy and paste error and bring some node
spaces back into line with the remainder of the tree.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>