Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 27 1月, 2012 1 次提交
    • W
      ipv6: Fix ip_gre lockless xmits. · f2b3ee9e
      由 Willem de Bruijn 提交于 
      Tunnel devices set NETIF_F_LLTX to bypass HARD_TX_LOCK.  Sit and
ipip set this unconditionally in ops->setup, but gre enables it
conditionally after parameter passing in ops->newlink. This is
not called during tunnel setup as below, however, so GRE tunnels are
still taking the lock.

modprobe ip_gre
ip tunnel add test0 mode gre remote 10.5.1.1 dev lo
ip link set test0 up
ip addr add 10.6.0.1 dev test0
 # cat /sys/class/net/test0/features
 # $DIR/test_tunnel_xmit 10 10.5.2.1
ip route add 10.5.2.0/24 dev test0
ip tunnel del test0

The newlink callback is only called in rtnl_netlink, and only if
the device is new, as it calls register_netdevice internally. Gre
tunnels are created at 'ip tunnel add' with ioctl SIOCADDTUNNEL,
which calls ipgre_tunnel_locate, which calls register_netdev.
rtnl_newlink is called at 'ip link set', but skips ops->newlink
and the device is up with locking still enabled. The equivalent
ipip tunnel works fine, btw (just substitute 'method gre' for
'method ipip').

On kernels before /sys/class/net/*/features was removed [1],
the first commented out line returns 0x6000 with method gre,
which indicates that NETIF_F_LLTX (0x1000) is not set. With ipip,
it reports 0x7000. This test cannot be used on recent kernels where
the sysfs file is removed (and ETHTOOL_GFEATURES does not currently
work for tunnel devices, because they lack dev->ethtool_ops).

The second commented out line calls a simple transmission test [2]
that sends on 24 cores at maximum rate. Results of a single run:

ipip:			19,372,306
gre before patch:	 4,839,753
gre after patch:	19,133,873

This patch replicates the condition check in ipgre_newlink to
ipgre_tunnel_locate. It works for me, both with oseq on and off.
This is the first time I looked at rtnetlink and iproute2 code,
though, so someone more knowledgeable should probably check the
patch. Thanks.

The tail of both functions is now identical, by the way. To avoid
code duplication, I'll be happy to rework this and merge the two.

[1] http://patchwork.ozlabs.org/patch/104610/
[2] http://kernel.googlecode.com/files/xmit_udp_parallel.cSigned-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f2b3ee9e
  3. 26 1月, 2012 2 次提交
  5. 23 1月, 2012 2 次提交
    • S
      tcp: md5: using remote adress for md5 lookup in rst packet · 8a622e71
      由 shawnlu 提交于 
      md5 key is added in socket through remote address.
remote address should be used in finding md5 key when
sending out reset packet.
Signed-off-by: Nshawnlu <shawn.lu@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8a622e71
    • Y
      tcp: detect loss above high_seq in recovery · 974c1236
      由 Yuchung Cheng 提交于 
      Correctly implement a loss detection heuristic: New sequences (above
high_seq) sent during the fast recovery are deemed lost when higher
sequences are SACKed.

Current code does not catch these losses, because tcp_mark_head_lost()
does not check packets beyond high_seq. The fix is straight-forward by
checking packets until the highest sacked packet. In addition, all the
FLAG_DATA_LOST logic are in-effective and redundant and can be removed.

Update the loss heuristic comments. The algorithm above is documented
as heuristic B, but it is redundant too because heuristic A already
covers B.

Note that this change only marks some forward-retransmitted packets LOST.
It does NOT forbid TCP performing further CWR on new losses. A potential
follow-up patch under preparation is to perform another CWR on "new"
losses such as
1) sequence above high_seq is lost (by resetting high_seq to snd_nxt)
2) retransmission is lost.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      974c1236
  7. 21 1月, 2012 2 次提交
    • N
      tcp: fix undo after RTO for CUBIC · 5a45f008
      由 Neal Cardwell 提交于 
      This patch fixes CUBIC so that cwnd reductions made during RTOs can be
undone (just as they already can be undone when using the default/Reno
behavior).

When undoing cwnd reductions, BIC-derived congestion control modules
were restoring the cwnd from last_max_cwnd. There were two problems
with using last_max_cwnd to restore a cwnd during undo:

(a) last_max_cwnd was set to 0 on state transitions into TCP_CA_Loss
(by calling the module's reset() functions), so cwnd reductions from
RTOs could not be undone.

(b) when fast_covergence is enabled (which it is by default)
last_max_cwnd does not actually hold the value of snd_cwnd before the
loss; instead, it holds a scaled-down version of snd_cwnd.

This patch makes the following changes:

(1) upon undo, revert snd_cwnd to ca->loss_cwnd, which is already, as
the existing comment notes, the "congestion window at last loss"

(2) stop forgetting ca->loss_cwnd on TCP_CA_Loss events

(3) use ca->last_max_cwnd to check if we're in slow start
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NSangtae Ha <sangtae.ha@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5a45f008
    • N
      tcp: fix undo after RTO for BIC · fc16dcd8
      由 Neal Cardwell 提交于 
      This patch fixes BIC so that cwnd reductions made during RTOs can be
undone (just as they already can be undone when using the default/Reno
behavior).

When undoing cwnd reductions, BIC-derived congestion control modules
were restoring the cwnd from last_max_cwnd. There were two problems
with using last_max_cwnd to restore a cwnd during undo:

(a) last_max_cwnd was set to 0 on state transitions into TCP_CA_Loss
(by calling the module's reset() functions), so cwnd reductions from
RTOs could not be undone.

(b) when fast_covergence is enabled (which it is by default)
last_max_cwnd does not actually hold the value of snd_cwnd before the
loss; instead, it holds a scaled-down version of snd_cwnd.

This patch makes the following changes:

(1) upon undo, revert snd_cwnd to ca->loss_cwnd, which is already, as
the existing comment notes, the "congestion window at last loss"

(2) stop forgetting ca->loss_cwnd on TCP_CA_Loss events

(3) use ca->last_max_cwnd to check if we're in slow start
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fc16dcd8
  9. 18 1月, 2012 1 次提交
  11. 17 1月, 2012 2 次提交
  13. 13 1月, 2012 2 次提交
  15. 12 1月, 2012 2 次提交
  17. 10 1月, 2012 1 次提交
  19. 08 1月, 2012 1 次提交
  21. 06 1月, 2012 1 次提交
  23. 31 12月, 2011 1 次提交
  25. 29 12月, 2011 1 次提交
  27. 28 12月, 2011 2 次提交
  29. 23 12月, 2011 9 次提交
  31. 22 12月, 2011 1 次提交
  33. 21 12月, 2011 2 次提交
  35. 20 12月, 2011 2 次提交
  37. 17 12月, 2011 2 次提交
  39. 16 12月, 2011 1 次提交
  41. 15 12月, 2011 1 次提交
  43. 13 12月, 2011 1 次提交