rtl8169_init_one
-> rtl_init_mac_address
   -> rtl_rar_set
      -> spin_lock_irq(&tp->lock);
[...]
-> spin_lock_init(&tp->lock);
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warnings caught by David Miller on sparc64
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to modulus the queue number in ->hard_start_xmit() since the
core is going to do that for you modulus ->real_num_tx_queues.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum.  For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF.  The
hardware takes care of this case but only if it is told the
packet is tcp.

same patch as e1000e
Signed-off-by: NDave Graham <david.graham@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum.  For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF.  The
hardware takes care of this case but only if it is told the
packet is tcp.
Signed-off-by: NDave Graham <david.graham@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before, the driver would not care about the return codes from pci_map_*
functions.  This could be potentially dangerous if a mapping failed.
Now, we will check all pci_map_* calls.  On the transmit side, we switch
to use the new function skb_dma_map().  On the receive side, we add
pci_dma_mapping_error().
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is now possible with updated firmware.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With this new firmware, the driver no longer has to modify the
TCP/IP header fields when transmitting TSO packets.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to check netif_running() state in most ethtool operations
and properly handle the !netif_running() state where the chip is
in an uninitailzed state or low power state that may not accept
any MMIO.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This logic is used in bnx2_close() and bnx2_suspend() and
so should be separated out into a separate function.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
   converted over to mdiobus_{alloc,free}().

2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
   struct fixed_mdio_bus and then use container_of() to go from the
   former to the latter.  Since mii bus structures are no longer
   embedded, we need to do something like use the mii bus private
   pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/jme.c:1598: warning: ‘jme_set_100m_half’ defined but not used
drivers/net/jme.c:1618: warning: ‘jme_wait_link’ defined but not used
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Advances the driver version after modification.
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix IRQ handle bug when interrupt mode.

The driver was incorrectly handled and returned IRQ_HANDLED
while the device is not generating the interrupt.
It happened due to faulty determination of interrupt status register.

Found by: "Ethan" <ethanhsiao@jmicron.com>
Fixed by: "akeemting" <akeem@jmicron.com>
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Set bit 5 of GPREG1 to 1 to enable hardware workaround for half-duplex
   mode. Which the MAC processor generates CRS/COL by itself instead of
   receive it from PHY processor.

2. Set bit 6 of GPREG1 to 1 to enable hardware workaround that masks the
   MAC processor working right while calculating IPv6 RSS in 10/100
   mode.

3. Group the workaround codes all together.
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 1G optical Vitesse PHY.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for SR PHY.
Auto-detect phy module type, and report type changes.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add generic code to manage interrupt driven PHYs.
Do not reset the phy after link parameters update,
the new values might get lost.
Return early from link change notification
when the link parameters remain unchanged.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not require PHY interrupts to be connected to GPIs in ascending order.
Base interrupt availability both on PHYs supporting them and on GPIs being
hooked up.  Allows boards to specify interrupt GPIs though the PHYs don't
use them.

Remove spurious PHY interrupts due to clearing T3DBG interrupts before
setting their polarity.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Second step in overall phy layer reorganization.
Clean up the port_type_info structure.
Support coextistence of clause 22 and clause 45 MDIO devices.
Select the type of MDIO transaction on a per transaction basis.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First step towards overall PHY layering re-organization.
Allow a status return when a PHY is reset.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate a queue set per core, up to the maximum of available qsets.
Share the queue sets on multi port adapters.
Rename MSI-X interrupt vectors ethX-N, N being the queue set number.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when a fatal error occurs, bring ports down, reset the chip,
and bring ports back up.

Factorize code used for both EEH and fatal error recovery.
Fix timer usage when bringing up/resetting sge queue sets.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The write barrier should be used before starting a DMA transfer. This fixes
a problem, where almost all packets received on another machine had garbled
content. Tested with an RTL8100C on a MIPS machine.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

there's several drivers that have use "tx_timeout" for the .. tx
timeout function.  All fine with that, they're static, however for
doing stats on how often which driver hits the timeout it's a tad
unfortunate. The patch below gives the ones I found in the
kerneloops.org database unique names.
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building with CONFIG_USB_DEBUG, don't create logspam from
the USB networking drivers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since recent kernel (2.6.26 or 2.6.27) the PCI wakeup functions are
influenced by generic device ability and configuration when enabling
PCI-device triggered wake-up.

This patch causes WoL setting to enable/disable device's wish to
be permitted to wake-up the host when changing WoL options and
also during device probing.

Without this patch one has write 'enabled' to
  /sys/bus/pci/devices/0000:02:08.0/power/wakeup
Signed-off-by: NBruno Prémont <bonbons@linux-vserver.org>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When probing the chip and handling it's power management settings
also remember wether WoL feature is enabled.

Without this patch one has to call ethtool to change WoL settings
for this flag to be set and any WoL being enabled on suspend to
RAM.
Signed-off-by: NBruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device's carrier status is controlled via the functions
netif_carrier_on() and netif_carrier_off().  These set or clear a bit
indicating the carrier (aka lower level link) is down, and if the state
changed, they fire off a routing netlink event.

Add a call to netif_carrier_off() before register_netdev() so that the
newly created device will be set to carrier down.  Then when the carrier
comes up for the first time, a netlink event will be generated, as the
carrier changed from down to up.  Otherwise the initial carrier up will
appear to be changing the status from up to up, and so no event is
generated since that's not a change.
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mv643xx_eth uses ip_hdr() (defined in linux/ip.h), but relied on
another header file to include the needed header file indirectly.
In latest net-next this indirect include chain is gone, so the
driver fails to build.  Include linux/ip.h explicitly to fix this.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This lockdep warning:
  =================================
  [ INFO: inconsistent lock state ]
  2.6.27-rc7 #3
  ---------------------------------
  inconsistent {in-softirq-W} -> {softirq-on-W} usage.
  syslogd/2474 [HC0[0]:SC0[0]:HE1:SE1] takes:
   (_xmit_ETHER#2){-+..}, at: [<c0265562>] netpoll_send_skb+0x132/0x190
  ...

is caused by unconditional local_irq_disable()/local_irq_enable() in
disable_irq_lockdep()/enable_irq_lockdep() used by __ei_poll(). Since
netconsole/netpoll always calls dev->poll_controller() with local irqs
disabled, disable_irq()/enable_irq() instead is safe and enough (like
e.g. in 3c509 or 8139xx drivers).
Reported-and-tested-by: NBernard Pidoux F6BVP <f6bvp@free.fr>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was pointed out by Breno Leitao <leitao@linux.vnet.ibm.com> that
ixgb would crash on PPC when an IOMMU was in use, if change_mtu was
called.

It appears to be a pretty simple issue in the driver that wasn't discovered
because most systems don't run with an IOMMU.  The driver needs to only unmap
buffers that are mapped (duh).

CC: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since e1000e has been existance in linux-2.6, we've
never released the hardware semaphore after a successful
write to the SPI EEPROM.  I guess we don't write to
SPI EEPROM much -- but those few of us that do appreciate
it when we can later read from the EEPROM without having
to reboot.
Found-by: NNick Van Fossen <Nick.VanFossen@riverbed.com>
Signed-off-by: NArthur Jones <ajones@riverbed.com>
Reviewed-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Attached is a driver for SMSC's LAN9500 USB2.0 10/100 ethernet
adapter.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce the mdio_bus class, and give each 'struct mii_bus' its own
'struct device', so that mii_bus objects are represented in the device
tree and can be found by querying the device tree.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NAndy Fleming <afleming@freescale.com>

In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NAndy Fleming <afleming@freescale.com>

Add multiqueue TX support to myri10ge.

[ Removed reference to deprecated CONFIG_NETDEVICES_MULTIQUEUE and
  NETIF_F_MULTI_QUEUE ]
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>