Also, remove usage of set_irq_type after request_irq.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add SDHC support for MX27ADS board
Signed-off-by: NVladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add 1-wire support for MX27ADS board
Signed-off-by: NVladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add Sharp-QVGA panel support for MX27ADS board
Signed-off-by: NVladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add I2C support for MX27ADS board
Signed-off-by: NVladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add NAND support for MX27ADS board
Signed-off-by: NVladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Setup all pins at once in one table
Signed-off-by: NVladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds the SMSC platform device to the Litekit board.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Several comments in board config files stated "mandatory for
CONFIG_LL_DEBUG" but the correct name is CONFIG_DEBUG_LL.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This support both sdhc1 and sdhc2 with WP and CD for the marxbot and
devboard mx31moboard baseboards.

sdhc2 is present on both, but is not directly included in the
mx31moboard file because a third baseboard (not supported yet) without
sdhc2 is planned.

Changes since v1: removed pin initialization from init/exit function and
taken different comments into account

Changes since v2: pin initialiation now is done in another patch for all
current mx31moboard pins
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Changes since v1: all the pins needed for the drivers are claimed in
another patch
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

As suggested by Sascha, here we setup all the pins that we are using in
the current (and currently reviewed) drivers for mx31moboard system.

changes since v1: changed I2C1 pin names
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

As suggested by Sascha, I regroup them in a single patch so that the
other patches become more orthogonal.

changes since v1: changed I2C1 pin names
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This hw-random driver add support to RNGA hardware found
on some i.MX processors.
Signed-off-by: NAlan Carvalho de Assis <acassis@gmail.com>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Various improvements (includes in alphabetical order, platform devices
declaration order change, ...)

The pins now are claimed in a single function call from a main table for
every board for a better clarity and to adopt the current agreement for
mx31 devices.
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds basic support to MX27PDK board http://www.freescale.com/imx27pdk ).
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Adds a defconfig file for the i.MX21 SoC, targeting
the Freescale i.MX21ADS (M9328MX21ADSE) Application
Development System.
Signed-off-by: NIvo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* Kconfig enables now HAVE_PWM (this enables in turn the selection of
  CONFIG_BACKLIGHT_PWM)
* changes CONFIG_ARCH_MXyy to CONFIG_MACH_MXyy
* fix some register names to match those of the reference manual
* write a stub code so that the PWM can be used to program the
  LCD backlight
* convert from #ifdef CONFIG_ARCH_MXxx to cpu_is_mxXX()
* remove unneeded defines and fix 80-column "violations" of checkpatch.pl
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

[PATCH v6] MXC: mx21ads base support

Base machine support for the  Freescale i.MX21ADS
(M9328MX21ADSE) Application Development System.
Signed-off-by: NIvo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add support for a QVGA Sharp LCD on pcm037.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

MXC GPIO controller does not support generation of interrupts on both
edges. Emulate this mode in software by reconfiguring the irq trigger
polarity on each interrupt. This follows an example of
drivers/mfd/asic3.c.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

arch-imx is superseeded by the MXC architecture support.
This patch removes arch/arm/mach-imx from the kernel.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Currently we depend on hardcoded base addresses for the interrupt
controller. This prevents us from compiling in more than one i.MX
architecture at a time. This patch changes the base address to a
runtime calculated one.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Currently we depend on hardcoded base addresses for the timer.
This prevents us from compiling in more than one i.MX architecture
at a time. This patch changes the base address to a runtime
calculated one.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This allows us to have more mapping functions for more than one
i.MX architecture in the kernel. As this is the earliest board
specific hook we have, also use it to set the cpu type.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

It is no longer present in newer cores. Unfortunately Freescale decided
to put the bit which decides between automotive clock path and consumer
clock path in the automotive clock path direction. With current code we
cannot detect the core revision, so just remove automotive path completely.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The PCM043 is a i.MX35 based board from Phytec also known as the
phyCORE-i.MX35.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This iomux is called iomux-v3 in the tree because it is the third known
incarnation of MXC iomuxers. It is not only found on the MX35 but also
on the MX51 and probably others.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The i.MX31 ARM11 core is not a v6K core. Disable this option as it
is incompatible with non v6K cores.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>