- 29 1月, 2008 4 次提交
-
-
由 Denis V. Lunev 提交于
Needed to propagate it down to the ip_route_output_flow. Signed-off-by: NDenis V. Lunev <den@openvz.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Lezcano 提交于
When a new address is added, we must check if the new address does not already exists. This patch makes this check to be aware of a network namespace, so the check will look if the address already exists for the specified network namespace. While the addresses are browsed, the addresses which do not belong to the namespace are discarded. Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com> Signed-off-by: NBenjamin Thery <benjamin.thery@bull.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
Most callers of the LOCAL_OUT chain will set the IP packet length before doing so. They also share the same output function dst_output. This patch creates a new function called ip6_local_out which does all of that and converts the appropriate users over to it. Apart from removing duplicate code, it will also help in merging the IPsec output path. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
This patch changes the prototype of ipv4_copy_dscp and ipv6_copy_dscp so that they directly take the outer DSCP rather than the outer IP header. This will help us to unify the code for inter-family tunnels. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 10月, 2007 1 次提交
-
-
由 Chuck Lever 提交于
In some places, the result of skb_headroom() is compared to an unsigned integer, and in others, the result is compared to a signed integer. Make the comparisons consistent and correct. Signed-off-by: NChuck Lever <chuck.lever@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 10月, 2007 2 次提交
-
-
由 Ralf Baechle 提交于
It's been a useless no-op for long enough in 2.6 so I figured it's time to remove it. The number of people that could object because they're maintaining unified 2.4 and 2.6 drivers is probably rather small. [ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ] Signed-off-by: NRalf Baechle <ralf@linux-mips.org> Signed-off-by: NJeff Garzik <jeff@garzik.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric W. Biederman 提交于
This patch makes most of the generic device layer network namespace safe. This patch makes dev_base_head a network namespace variable, and then it picks up a few associated variables. The functions: dev_getbyhwaddr dev_getfirsthwbytype dev_get_by_flags dev_get_by_name __dev_get_by_name dev_get_by_index __dev_get_by_index dev_ioctl dev_ethtool dev_load wireless_process_ioctl were modified to take a network namespace argument, and deal with it. vlan_ioctl_set and brioctl_set were modified so their hooks will receive a network namespace argument. So basically anthing in the core of the network stack that was affected to by the change of dev_base was modified to handle multiple network namespaces. The rest of the network stack was simply modified to explicitly use &init_net the initial network namespace. This can be fixed when those components of the network stack are modified to handle multiple network namespaces. For now the ifindex generator is left global. Fundametally ifindex numbers are per namespace, or else we will have corner case problems with migration when we get that far. At the same time there are assumptions in the network stack that the ifindex of a network device won't change. Making the ifindex number global seems a good compromise until the network stack can cope with ifindex changes when you change namespaces, and the like. Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 7月, 2007 1 次提交
-
-
由 Al Viro 提交于
Convert rel_info to host-endian before calling ip6_tnl_err(). The things become much more straightforward that way. The key observation (and the reason why that code actually worked) is that after ip6_tnl_err() we either immediately bailed out or had rel_info set to 0 or had it set to host-endian and guaranteed to hit (rel_type == ICMP_DEST_UNREACH && rel_code == ICMP_FRAG_NEEDED) case. So inconsistent endianness didn't really lead to bugs, but it had been subtle and prone to breakage. New variant is saner and obviously safe. Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 22 7月, 2007 1 次提交
-
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 7月, 2007 1 次提交
-
-
由 Patrick McHardy 提交于
Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 4月, 2007 12 次提交
-
-
由 Arnaldo Carvalho de Melo 提交于
Renaming skb->h to skb->transport_header, skb->nh to skb->network_header and skb->mac to skb->mac_header, to match the names of the associated helpers (skb[_[re]set]_{transport,network,mac}_header). Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
Now the skb->nh union has just one member, .raw, i.e. it is just like the skb->mac union, strange, no? I'm just leaving it like that till the transport layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or ->mac_header_offset?), ditto for ->{h,nh}. Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
For the places where we need a pointer to the network header, it is still legal to touch skb->nh.raw directly if just adding to, subtracting from or setting it to another layer header. Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
skb_push updates and returns skb->data, so we can just call skb_reset_network_header after the call to skb_push. Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in 64bit land while possibly keeping it as a pointer on 32bit. This one touches just the most simple case, next will handle the slightly more "complex" cases. Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yasuyuki Kozakai 提交于
ip6_tunnel before supporting IPv4/IPv6 tunnel allows only IPPROTO_IPV6 in configurations from userland. This allows userland to set IPPROTO_IPIP and 0(wildcard). ip6_tunnel only handles allowed inner protocols. Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yasuyuki Kozakai 提交于
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yasuyuki Kozakai 提交于
Some notes - Protocol number IPPROTO_IPIP is used for IPv4 over IPv6 packets. - If IP6_TNL_F_USE_ORIG_TCLASS is set, TOS in IPv4 header is copied to Traffic Class in outer IPv6 header on xmit. - IP6_TNL_F_USE_ORIG_FLOWLABEL is ignored on xmit of IPv4 packets, because IPv4 header does not have flow label. - Kernel sends ICMP error if IPv4 packet is too big on xmit, even if DF flag is not set. Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yasuyuki Kozakai 提交于
This enables to add IPv4/IPv6 specific handling later, Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yasuyuki Kozakai 提交于
This enables to add IPv4/IPv6 specific handling later, Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yasuyuki Kozakai 提交于
This enables to add IPv4/IPv6 specific error handling later, Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 2月, 2007 1 次提交
-
-
由 Yasuyuki Kozakai 提交于
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
-
- 14 2月, 2007 1 次提交
-
-
由 Kazunori MIYAZAWA 提交于
This patch changes xfrm6_tunnel register and deregister interface to prepare for solving the conflict of device tunnels with inter address family IPsec tunnel. There is no device which conflicts with IPv4 over IPv6 IPsec tunnel. Signed-off-by: NKazunori MIYAZAWA <miyazawa@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 2月, 2007 1 次提交
-
-
由 YOSHIFUJI Hideaki 提交于
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 2月, 2007 1 次提交
-
-
由 Stephen Hemminger 提交于
There was no real useful information from the unregister_netdevice() return code, the only error occurred in a situation that was a driver bug. So change it to a void function. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 12月, 2006 9 次提交
-
-
由 Ville Nuorvala 提交于
Log an error if the remote tunnel endpoint is unable to handle tunneled packets. Signed-off-by: NVille Nuorvala <vnuorval@tcs.hut.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ville Nuorvala 提交于
Signed-off-by: NVille Nuorvala <vnuorval@tcs.hut.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ville Nuorvala 提交于
Allow link-local tunnel endpoints if the underlying link is defined. Signed-off-by: NVille Nuorvala <vnuorval@tcs.hut.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ville Nuorvala 提交于
Doing the mandatory tunnel endpoint checks when the tunnel is set up isn't enough as interfaces can go up or down and addresses can be added or deleted after this. The checks need to be done realtime when the tunnel is processing a packet. Signed-off-by: NVille Nuorvala <vnuorval@tcs.hut.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ville Nuorvala 提交于
A logic bug in tunnel lookup could result in duplicate tunnels when changing an existing device. Signed-off-by: NVille Nuorvala <vnuorval@tcs.hut.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gerrit Renker 提交于
Throughout the TCP/DCCP (and tunnelling) code, it often happens that the return code of a transmit function needs to be tested against NET_XMIT_CN which is a value that does not indicate a strict error condition. This patch uses a macro for these recurring situations which is consistent with the already existing macro net_xmit_errno, saving on duplicated code. Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 11月, 2006 2 次提交
-
-
由 Yasuyuki Kozakai 提交于
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
-
由 Yasuyuki Kozakai 提交于
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
-
- 22 7月, 2006 1 次提交
-
-
由 Panagiotis Issaris 提交于
Signed-off-by: NPanagiotis Issaris <takis@issaris.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 7月, 2006 1 次提交
-
-
由 Jörn Engel 提交于
Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 10 4月, 2006 1 次提交
-
-
由 Herbert Xu 提交于
This patch moves the sending of ICMP messages when there are no IPv4/IPv6 tunnels present to tunnel4/tunnel6 respectively. Please note that for now if xfrm4_tunnel/xfrm6_tunnel is loaded then no ICMP messages will ever be sent. This is similar to how we handle AH/ESP/IPCOMP. This move fixes the bug where we always send an ICMP message when there is no ip6_tunnel device present for a given packet even if it is later handled by IPsec. It also causes ICMP messages to be sent when no IPIP tunnel is present. I've decided to use the "port unreachable" ICMP message over the current value of "address unreachable" (and "protocol unreachable" by GRE) because it is not ambiguous unlike the other ones which can be triggered by other conditions. There seems to be no standard specifying what value must be used so this change should be OK. In fact we should change GRE to use this value as well. Incidentally, this patch also fixes a fairly serious bug in xfrm6_tunnel where we don't check whether the embedded IPv6 header is present before dereferencing it for the inside source address. This patch is inspired by a previous patch by Hugo Santos <hsantos@av.it.pt>. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-