Due to HW limitations, indexes to MAC and VLAN tables are always taken
from the table of the actual port. So, if a resource holds an index to
a table, it may refer to different values during the lifetime of the
resource,  unless the tables are mirrored. Also, even when
driver is not in HA mode the policy of allocating an index to these
tables is such to make sure, as much as possible, that when the time
comes the mirroring will be successful. This means that in multifunction
mode the allocation of a free index in a port's table tries to make sure
that the same index in the other's port table is also free.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under HA mode, steering rules set by VFs should be mirrored on both
ports of the device so packets will be accepted no matter on which
port they arrived.

Since getting into HA mode is done dynamically when the user bonds mlx4
Ethernet netdevs, we keep hold of the VF DMFS rule mbox with the port
value flipped (1->2,2->1) and execute the mirroring when getting into
HA mode. Later, when going out of HA mode, we unset the mirrored rules.
In that context note that mirrored rules cannot be removed explicitly.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under HA mode, the link down event should be sent to VFs only if both
ports are down.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In HA mode, the link state for VFs for which the policy is "auto"
(i.e. follow the physical link state) should be ORed from both ports.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Better to just warn the user that something really odd is going on and
continue to run.
Suggested-by: NOr Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement and enable SR-IOV ndos to manage SR-IOV configuration via
netdev netlink API.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to get VF statistics using query vport
counter command.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add query and modify functions to control client vlan and qos
striping or insertion, in E-Switch vports contexts.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

E-Switch vport context is unlike NIC vport context, managed by the
E-Switch manager or vport_group_manager and not by the NIC(VF) driver.

The E-Switch manager can access (read/modify) any of its vports
E-Switch context.

Currently E-Switch vport context includes only clietnt and server
vlan insertion and striping data (for later support of VST mode).
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement set VF mac/link state and query VF config
to be used later in nedev VF ndos or any other management API.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling E-Switch SRIOV for nvfs+1 vports.

Create E-Switch FDB for L2 UC/MC mac steering between VFs/PF and
external vport (Uplink).

FDB contains forwarding rules such as:
	UC MAC0 -> vport0(PF).
	UC MAC1 -> vport1.
	UC MAC2 -> vport2.
	MC MACX -> vport0, vport2, Uplink.
	MC MACY -> vport1, Uplink.

For unmatched traffic FDB has the following default rules:
	Unmached Traffic (src vport != Uplink) -> Uplink.
	Unmached Traffic (src vport == Uplink) -> vport0(PF).

FDB rules population:
Each NIC vport (VF) will notify E-Switch manager of its UC/MC vport
context changes via modify vport context command, which will be
translated to an event that will be handled by E-Switch manager (PF)
which will update FDB table accordingly.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define needed hardware structures and capabilities needed
for E-Switch FDB flow tables and read them on driver load.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

E-Switch is the software entity that represents and manages ConnectX4
inter-HCA ethernet l2 switching.

E-Switch has its own Virtual Ports, each Vport/vNIC/VF can be
connected to the device through a vport of an e-switch.

Each e-switch is managed by one vNIC identified by
HCA_CAP.vport_group_manager (usually it is the PF/vport[0]),
and its main responsibility is to forward each packet to the
right vport.

e-Switch needs to manage its own l2-table and FDB tables.

L2 table is a flow table that is managed by FW, it is needed for
Multi-host (Multi PF) configuration for inter HCA switching between
PFs.

FDB table is a flow table that is totally managed by e-Switch driver,
its main responsibility is to switch packets between e-Swtich internal
vports and uplink vport that belong to the same.

This patch introduces only e-Swtich l2 table management, FDB managemnt
will come later when ethernet SRIOV/VFs will be enabled.

preperation for ethernet sriov and l2 table management.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each Vport/vNIC must notify underlying e-Switch layer
for vlan table changes in-order to update SR-IOV FDB tables.

We do that at vlan_rx_add_vid and vlan_rx_kill_vid ndos.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each Vport/vNIC must notify underlying e-Switch layer
for UC/MC list and promisc mode updates, in-order to update
l2 tables and SR-IOV FDB tables.

We do that at set_rx_mode ndo.

preperation for ethernet-SRIOV and l2 table management.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) vlan table changes.

preperation for ethernet sriov and l2 table management.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Those functions are needed to notify the upcoming SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) promisc mode changes.

Preperation for ethernet sriov and l2 table management.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for SR-IOV we add here an API to enable each e-switch
manager (PF) to configure its VFs link states in e-switch

preparation for ethernet sriov.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) UC/MC mac lists
changes.

preperation for ethernet sriov and l2 table management.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for SR-IOV we add here an API to enable each e-switch
client (PF/VF) to configure its L2 MAC addresses and for the e-switch
manager (usually the PF) to access them in order to be able to
configure them into the e-switch.
Therefore we now pass vport num parameter to
mlx5_query_nic_vport_context, so PF can access other vports contexts.

preperation for ethernet sriov and l2 table management.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds SRIOV base support for mlx5 supported devices. The same
driver is used for both PFs and VFs; VFs are identified by the driver
through the flag MLX5_PCI_DEV_IS_VF added to the pci table entries.
Virtual functions are created as usual through writing a value to the
sriov_numvs sysfs file of the PF device. Upon instantiating VFs, they will
all be probed by the driver on the hypervisor. One can gracefully unbind
them through /sys/bus/pci/drivers/mlx5_core/unbind.

mlx5_wait_for_vf_pages() was added to ensure that when a VF dies without
executing proper teardown, the hypervisor driver waits till all of the
pages that were allocated at the hypervisor to maintain its operation
are returned.

In order for the VF to be operational, the PF needs to call enable_hca
for it. This can be done before the VFs are created through a call to
pci_enable_sriov.

If the there are VFs assigned to a VMs when the driver of the PF is
unloaded, all the VF will experience system error and PF driver unloads
cleanly; in this case pci_disable_sriov is not called and the devices
will show when running lspci. Once the PF driver is reloaded, it will
sync its data structures which maintain state on its VFs.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify these functions to have func_id argument to state which device we
are referring to. This is done as a preparation for SRIOV support where
a PF driver needs to control its virtual functions.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling/disabling TX on a LAG port means enabling/disabling distribution
in our HW.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement FDB offloading for lagged ports, including learning LAG FDB
entries, adding/removing static FDB entries and dumping existing LAG FDB
entries.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement basic procedures for joining/leaving port to/from LAG. That
includes HW setup of collector, core LAG mapping setup.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LAG-related records have specific format in SFN register.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LAG-related records have specific format in SFD register.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add definitions of SLDR, SLCR2, SLCOR registers that are used to
configure LAG.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Completion queue element for receive queue provides information if the
packet was received via LAG port. Extract this info and pass it along
to core.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lower layer (pci) has information if the packet is received via LAG port.
If that is the case, it fills up rx_info accordingly. However upper
layer does not care about lag_id/port_index for received packets so
convert it to local_port before passing it up. For that conversion, lag
mapping array is introduced. Upper layer is responsible for setting up
the mapping according to what is set in HW.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add just a stub for now. This allows to pass check in dev_ifsioc,
SIOCADDMULTI and SIOCDELMULTI cases. Teamd is using these to add LACP
slow MAC.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ASIC provides access to fans. Implement their exposure to userspace
using hwmon.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add definition of MFCR, MFSC and MFSM which provide possibility to
control and monitor fans.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ASIC provides access to temperature sensors. Implement their exposure to
userspace using hwmon.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add definition of MTCAP and MTMP registers which provide access to
temperature sensors.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow a user to flash the port's LED in order to identify it. This is
achieved by setting the Management LED Control Register (MLCR).
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the MLCR register, which controls physical port identification LEDs.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The operation of adding VLANs on a port via switchdev ops can fail and
we need to be prepared for it. If we do not rollback hardware operations
following a failure, hardware and software will remain in an
inconsistent state.

Solve that by adding suitable error paths to __mlxsw_sp_port_vlans_add.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When adding or deleting VLANs from a bridged port, HW VLAN filters must be
set accordingly. Instead of having the same code in both add and delete
functions, just wrap it in a function and call it with the appropriate
parameters.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing a range of VLANs in which PVID is a member we should use
the correct PVID value instead of some VLAN in the range.

Also, change two print statements to use 'dev' instead of
'mlxsw_sp_port->dev', as it's already used in other print statements in
the function.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>