Programming the interrupt coalescing (IC) registers while
the controller/DMA is on may incur the loss of one Tx
confirmation interrupt, under certain conditions.  This is
a subtle hw race because it does not occur during a burst
of Tx packets.  It has been observed on p2020 devices that,
if just one packet is being xmit'ed, the Tx confirmation
doesn't trigger and BQL evetually blocks the Tx queues,
followed by Tx timeout and an un-responsive device.
This issue was not apparent prior to introducing BQL
support, as a late Tx confirmation was not an issue back then
and the next burst of Tx frames would have triggered the
Tx confirmation/ Tx ring cleanup anyway.

Bottom line, the hw specifications state that the IC registers
should not be programmed while the Rx/Tx blocks (the DMA) are
enabled. Further more, these registers are currently re-written
with the same values on the processing path, over and over again.
To fix this, rewriting the IC registers has been removed from
the processing path (napi poll).  A complete MAC reset procedure
has been implemented for the ethtool -c option instead, to
reliably update these registers while the controller is stopped.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device reset procedure, stop_gfar()/startup_gfar(), has
concurrency issues.
"Kernel access of bad area" oopses show up during Tx timeout
device reset or other reset cases (like changing MTU) that
happen while the interface still has traffic. The oopses
happen in start_xmit and clean_tx_ring when accessing tx_queue->
tx_skbuff which is NULL. The race comes from de-allocating the
tx_skbuff while transmission and napi processing are still
active. Though the Tx queues get temoprarily stopped when Tx
timeout occurs, they get re-enabled as a result of Tx congestion
handling inside the napi context (see clean_tx_ring()). Not
disabling the napi during reset is also a bug, because
clean_tx_ring() will try to access tx_skbuff while it is being
de-alloc'ed and re-alloc'ed.

To fix this, stop_gfar() needs to disable napi processing
after stopping the Tx queues. However, in order to prevent
clean_tx_ring() to re-enable the Tx queue before the napi
gets disabled, the device state DOWN has been introduced.
It prevents the Tx congestion management from re-enabling the
de-congested Tx queue while the device is brought down.
An additional locking state, RESETTING, has been introduced
to prevent simultaneous resets or to prevent configuring the
device while it is resetting.
The bogus 'rxlock's (for each Rx queue) have been removed since
their purpose is not justified, as they don't prevent nor are
suited to prevent device reset/reconfig races (such as this one).
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RCTRL and TCTRL registers should not be changed
on-the-fly, while the controller is running, otherwise
unexpected behaviour occurs.  But that's exactly what
gfar_vlan_mode() does, updating the VLAN acceleration
bits inside RCTRL/TCTRL.  The attempt to lock these
operations doesn't help, but only adds to the confusion.
There's also a dependency for Rx FCB insertion (activating
/de-activating the TOE offload block on Rx) which might
change the required rx buffer size.  This makes matters
worse as gfar_vlan_mode() ends up calling gfar_change_mtu(),
though the MTU size remains the same.  Note that there are
other situations that may affect the required rx buffer size,
like changing RXCSUM or rx hw timestamping, but errorneously
the rx buffer size is not recomputed/ updated in the process.

To fix this, do the vlan updates properly inside the MAC
reset and reconfiguration procedure, which takes care of
the rx buffer size dependecy and the rx TOE block (PRSDEP)
activation/deactivation as well (in the correct order).
As a consequence, MTU/ rx buff size updates are done now
by the same MAC reset and reconfig procedure, so that out
of context updates to MAXFRM, MRBLR, and MACCFG inside
change_mtu() are no longer needed.  The rx buffer size
dependecy to Rx FCB is now handled for the other cases too
(RXCSUM and rx hw timestamping).
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gfar_clean_rx_ring() was designed to be called from napi
(rx softirq) context to do the Rx processing. Calling it
from a process context like this is a bug as it will
clearly race with the napi Rx processing.

There's also no point in initializing num_txbdfree since
startup_gfar() already does that, when bringing the device
up again (after reset). Changing num_txbdfree "on-the-fly"
like this is also subject to race conditions.  num_txbdfree
is handled by the Tx processing path and the device reset
procedure.  Also, don't assume that num_rx_queues is always
equal to num_tx_queues.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gfar_halt() and gfar_start() are responsible for stopping
and starting the DMA and the Rx/Tx hw rings. They implement
the support for the "graceful Rx/Tx stop/start" hw procedure,
and also disable/enable eTSEC's hw interrupts in the process.

The GRS/GTS procedure requires however to have the RQUEUE/TQUEUE
registers cleared first and to wait for a period of time for the
current frame to pass through the interface (around ~10ms for a
jumbo frame). Only then may the GTS and GRS bits from DMACTRL be
set to shut down the DMA, and finally the Tx_EN and Rx_EN bits in
MACCFG1 may be cleared to disable the Tx/Rx blocks.

The same register programming order applies to start the Rx/Tx:
enabling the RQUEUE/TQUEUE *before* clearing the GRS/GTS bits.

This is a HW recommendation in order to avoid a possible
controller "lock up" during graceful reset.

Cleanup the gfar_halt()/start() prototypes, to take priv instead
of ndev as their purpose is to operate on HW. Enabling the
RQUEUE/TQUEUE in the hw_init() is not needed anymore since
that's the job of gfar_start().
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.   Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes unhandled register write in gianfar_ethtool.c.
Fixes following endianess related functional issues,
reported by sparse as well, i.e.:

gianfar_ethtool.c:1058:33: warning:
    incorrect type in argument 1 (different base types)
    expected unsigned int [unsigned] [usertype] value
    got restricted __be32 [usertype] ip4src

gianfar_ethtool.c:1164:33: warning:
    restricted __be16 degrades to integer

gianfar_ethtool.c:1669:32: warning:
    invalid assignment: ^=
    left side has type restricted __be16
    right side has type int

Solves all the sparse warnings for mixig normal pointers
with __iomem pointers for gianfar_ptp.c, i.e.:
gianfar_ptp.c:163:32: warning:
    incorrect type in argument 1 (different address spaces)
    expected unsigned int [noderef] <asn:2>*addr
    got unsigned int *<noident>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits.  These bits must not be set
however when eTSEC is operated in Half-Duplex mode.  Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface.  When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner.  If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A).  Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: NLutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging style.

Convert pr_<level> to netdev_<level> when a struct net_device is
available.  Add pr_fmt and neaten other formats too.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GRO_DROP return code is handled by the core network layer.
The current kernel approach is to factorize this kind of statistics into
the upper layers, instead of having all the drivers maintaining them.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only place where gfar_configure_coalescing is called
with an actual bitmask (other than 0xff) is in gfar_poll
(on the hot path). So make gfar_configure_coalescing()
static for the buffer processing path, and export
gfar_configure_coalescing_all() for the remaining cases
that require to set coalescing for all the queues at once
(on the slow path).
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While looking at some asm dump for an unrelated change, Eric
noticed in the following stats count increment code:

    50b8:       81 3c 01 f8     lwz     r9,504(r28)
    50bc:       81 5c 01 fc     lwz     r10,508(r28)
    50c0:       31 4a 00 01     addic   r10,r10,1
    50c4:       7d 29 01 94     addze   r9,r9
    50c8:       91 3c 01 f8     stw     r9,504(r28)
    50cc:       91 5c 01 fc     stw     r10,508(r28)

that a 64 bit counter was used on ppc-32 without sync
and hence the "ethtool -S" output was racy.

Here we convert all the values to use atomic64_t so that
the output will always be consistent.
Reported-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

The gfar_stats struct is only used in copying out data
via ethtool.  It is declared as the extra stats, followed
by the rmon stats.  However, the rmon stats are never
actually ever used in the driver; instead the rmon data
is a u32 register read that is cast directly into the
ethtool buf.

It seems the only reason rmon is in the struct at all is
to give the offset(s) at which it should be exported into
the ethtool buffer.  But note gfar_stats doesn't contain
a gfar_extra_stats as a substruct -- instead it contains
a u64 array of equal element count.  This implicitly means
we have two independent declarations of what gfar_extra_stats
really is.  Rather than have this duality, we already have
defines which give us the offset directly, and hence do not
need the struct at all.

Further, since we know the extra_stats is unconditionally
always present, we can write it out to the ethtool buf
1st, and then optionally write out the rmon data.  There
is no need for two independent loops, both of which are
simply copying out the extra_stats to buf offset zero.

This also helps pave the way towards allowing the extra
stats fields to be converted to atomic64_t values, without
having their types directly influencing the ethtool stats
export code (gfar_fill_stats) that expects to deal with u64.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

alloc failures already get standardized OOM
messages and a dump_stack.

Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a build failure introduced in commit 66636287
("gianfar: Support the get_ts_info ethtool method."). Not only was a
global variable inconsistently named, but also it was not exported as
it should have been.

This fix is also needed in stable version 3.5.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text.  Bring them up to date.  No actual change to
any code takes place here.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the driver only uses location values to maintain an ordered
list of filters.  Make it reject location values >= MAX_FILER_IDX
passed to the ETHTOOL_SRXCLSRLINS command, consistent with the range
it reports for the ETHTOOL_GRXCLSRLALL command.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NSebastian Pöhn <sebastian.poehn@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: NThomas Meyer <thomas@m3y3r.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v2:	add couple missing conversions in drivers
	split unexporting netdev_fix_features()
	implemented %pNF
	convert sock::sk_route_(no?)caps
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A user-space process must use ETHTOOL_GRXCLSRLCNT to find the number
of classification rules, then allocate a buffer of the right size,
then use ETHTOOL_GRXCLSRLALL to fill the buffer.  If some other
process inserts or deletes a rule between those two operations,
the user buffer might turn out to be the wrong size.

If it's too small, the return value will be -EMSGSIZE.  But if it's
too large, there is no indication of this.  Fix this by updating
the rule_cnt field on return.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.

Add note that drivers must not use ethtool_rxnfc::rule_locs.

The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.

CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

- unify vlan and nonvlan rx path
- kill priv->vlgrp and gfar_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch:
# improves readability of some gianfar nfc code
Signed-off-by: NSebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds all missing functionalities for nfc except GRXFH. There is so much code because hardware has not a TCAM.
Further hardware rule space is very limited. So I had to extensively use
optimization features. Both reasons lead to the necessity to hold all
online flows in a linked-list.

Change-log:
# Some suggestions by Joe Perches applied (thanks!)
# Shorted some logs
# Use memcmp() for comparing
Signed-off-by: NSebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the current logging styles.

Add #define DEBUG to get same output for <foo>_dbg messages.
Convert a few bare printks to pr_err.

Fix a likely copy/paste defect where a test was done with RX values:
        if (num_rx_qs > MAX_RX_QS) {
but TX limits were emitted:
        printk(KERN_ERR "num_rx_qs(=%d) greater than MAX_RX_QS(=%d)\n",
                              num_tx_qs, MAX_TX_QS);
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

Each eTSEC device should own localized filer table.
Signed-off-by: NJiajun Wu <b06378@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note: I bet that gfar_set_features() don't really need a full reset.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code was cribbed from niu, so gfar_set_hash_opts() begins by
converting the ethtool flow class code into a class code for Sun
Neptune hardware, then does the same thing again for the hardware it's
really dealing with.  It may also return -1 (-EPERM) for some
unhandled ethtool flow class codes.

Remove the useless code and definitions, and fix the error code.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The gianfar driver calls device_set_wakeup_enable() under a spinlock,
which causes a problem to happen after the recent core power
management changes, because this function can sleep now.  Fix this
by moving the device_set_wakeup_enable() call out of the
spinlock-protected area.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should be a _restore() instead of a _save().
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

This patch provides basic hash rules programming via the ethtool
interface.
Signed-off-by: NSandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>