Rename touch properties to match established nomenclature, and define
the maximum number of fingers.
Tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

The early generations with this trackpad used the separate mouse
interface to produce button events. With the introduction of the
button pads, this information was moved to the trackpad interface,
leaving the mouse interface unused. The driver is still setting up
both interfaces, which has not caused any problems - until now.

It turns out that without the CONFIG_USB_EHCI_TT_NEWSCHED option, the
driver may return an ENOSPC upon bt_urb submission, resulting in a
failure to open the device. This happens everytime on the MacBookPro
Retina (and likely on other mid-2012 models), but earlier MacBook
models seem to work fine.

This patch skips the bt_urb setup for TYPE2 devices, which arguably
should have been done in the first place.
Tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Add support for the Flatfrog Multitouch 3200 panel. This panel
advertises some fields that it does not use, hence the new quirk.

Cc: Pablo Cases <pablo.cases@flatfrog.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Some devices report the number of contacts via the unreliable
CONTACTCOUNT usage, rather than using the CONTACTMAX feature.
Without this patch, the 3M devices are constrained to the default
maximum of ten fingers.

Cc: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

With the input_mt_sync_frame() function in place, there is no longer
any need to keep the full touch state in the driver. This patch
removes the slot state and replaces the lookup code with the input-mt
equivalent.
Reviewed-and-tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

With the input_configured() callback in place, the setup and frame
synchronization can be simplified. The input device initialization is
moved to mt_input_configured(), to make sure the full HID report has been
seen.
Reviewed-and-tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Some recent hardware define more than 128 fields in the report
descriptor. Increase the limit to 256. This adds another kilobyte of
memory per report.
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

A hid device may create several input devices, and a driver may need
to prepare or finalize the configuration per input device. Currently,
there is no sane way for a driver to know when a device has been
configured. This patch adds a callback providing that information.
Reviewed-and-tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Some drivers like to report ABS_PRESSURE in a special way.
Allow this when ABS_MT_PRESSURE is not defined.
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Some devices use an internal key for tracking which cannot be directly
mapped to slots. This patch provides a key-to-slot mapping, which can
be used by drivers of such devices.
Reviewed-and-tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

With the INPUT_MT_TRACK flag set, the function input_mt_assign_slots()
can be used to match a new set of contacts against the currently used
slots. The algorithm used is based on Lagrange relaxation, and performs
very well in practice; slower than mtdev for a few corner cases, but
faster in most commonly occuring cases.
Tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Most MT drivers perform the same actions on frame synchronization.
Some actions, like dropping unseen contacts, are also unnecessarily
complex. Collect common frame synchronization tasks in a new function,
input_mt_sync_frame(). Depending on the flags set, it drops unseen
contacts and performs pointer emulation.

With init flags and frame synchronization in place, most MT drivers
can be simplified. First out are the bcm5974 and hid-multitouch
drivers, following this patch.
Reviewed-and-tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Preparing to move more repeated code into the mt core, add a flags
argument to the input_mt_slots_init() function.
Reviewed-and-tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

By sending a full frame of events at the same time, the irqsoff
latency at heavy load is brought down from 200 us to 100 us.

Cc: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

On heavy event loads, such as a multitouch driver, the irqsoff latency
can be as high as 250 us.  By accumulating a frame worth of data
before passing it on, the latency can be dramatically reduced.  As a
side effect, the special EV_SYN handling can be removed, since the
frame is now atomic.

This patch adds the events() handler callback and uses it if it
exists. The latency is improved by 50 us even without the callback.

Cc: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Tested-by: NSedat Dilek <sedat.dilek@gmail.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Preparing to split event filtering and event passing, move the
autorepeat function to the point where the event is actually passed.
Tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

For some EV_KEY types, sending a larger-than-one value causes the
input state to oscillate. This patch makes sure this cannot happen,
clearing up the autorepeat bypass logic in the process.
Tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

The events-per-packet estimate has so far been used by MT devices
only. This patch adjusts the packet buffer size to also accomodate the
KEY and MSC events.  Keyboards normally send one or two keys at a
time. MT devices normally send a number of button keys along with the
MT information.  The buffer size chosen here covers those cases, and
matches the default buffer size in evdev. Since the input estimate is
now preferred, remove the special input-mt estimate.
Reviewed-and-tested-by: NPing Cheng <pingc@wacom.com>
Tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Move all MT-related things to a separate place. This saves some
bytes for non-mt input devices, and prepares for new MT features.
Reviewed-and-tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.

Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.

This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: NAndreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull KVM bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix KVM_GET_MSR for PV EOI
  kvm: Fix nonsense handling of compat ioctl

Pull PARISC fixes from James Bottomley:
 "This is a set of two bug fixes.  One is the ATOMIC problem which is
  now causing a compile failure in certain situations.  The other is
  mishandling of PER_LINUX32 which may also cause user visible effects.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix personality flag check in copy_thread()
  [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts

Pull s390 fixes from Martin Schwidefsky:
 "A couple of s390 bug fixes for 3.5-rc4"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/32: Don't clobber personality flags on exec
  s390/smp: add missing smp_store_status() for !SMP
  s390/dasd: fix ioctl return value
  s390: Always use "long" for ssize_t to match size_t

Pull drm fixes from Dave Airlie:
 "A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
  nothing too shocking or different."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
  gma500: Consider CRTC initially active.
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm: Check for invalid cursor flags
  drm: Initialize object type when using DRM_MODE() macro
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Alex writes:

Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS

[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: NForest Bond <forest.bond@rapidrollout.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Pull btrfs fixes from Chris Mason:
 "I've split out the big send/receive update from my last pull request
  and now have just the fixes in my for-linus branch.  The send/recv
  branch will wander over to linux-next shortly though.

  The largest patches in this pull are Josef's patches to fix DIO
  locking problems and his patch to fix a crash during balance.  They
  are both well tested.

  The rest are smaller fixes that we've had queued.  The last rc came
  out while I was hacking new and exciting ways to recover from a
  misplaced rm -rf on my dev box, so these missed rc3."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: fix that repair code is spuriously executed for transid failures
  Btrfs: fix ordered extent leak when failing to start a transaction
  Btrfs: fix a dio write regression
  Btrfs: fix deadlock with freeze and sync V2
  Btrfs: revert checksum error statistic which can cause a BUG()
  Btrfs: remove superblock writing after fatal error
  Btrfs: allow delayed refs to be merged
  Btrfs: fix enospc problems when deleting a subvol
  Btrfs: fix wrong mtime and ctime when creating snapshots
  Btrfs: fix race in run_clustered_refs
  Btrfs: don't run __tree_mod_log_free_eb on leaves
  Btrfs: increase the size of the free space cache
  Btrfs: barrier before waitqueue_active
  Btrfs: fix deadlock in wait_for_more_refs
  btrfs: fix second lock in btrfs_delete_delayed_items()
  Btrfs: don't allocate a seperate csums array for direct reads
  Btrfs: do not strdup non existent strings
  Btrfs: do not use missing devices when showing devname
  Btrfs: fix that error value is changed by mistake
  Btrfs: lock extents as we map them in DIO
  ...

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix a warning for watchdog-test.c and it will remove a
  duplicate include of delay.h"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: da9052: Remove duplicate inclusion of delay.h
  watchdog: fix watchdog-test.c build warning

cache_grow() can reenable irqs so the cpu (and node) can change, so ensure
that we take list_lock on the correct nodelist.

This fixes an issue with commit 072bb0aa ("mm: sl[au]b: add
knowledge of PFMEMALLOC reserve pages") where list_lock for the wrong
node was taken after growing the cache.
Reported-and-tested-by: NHaggai Eran <haggaie@mellanox.com>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.

https://bugzilla.redhat.com/show_bug.cgi?id=785375Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Adjust the panel mode setup to match the behavior
of the vbios.  Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Power gating is per crtc pair, but the powergating registers
should be called individually.  The hw handles power up/down
properly.  The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down.  This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders.  We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs.  This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Some plls are shared for DP.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>

Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>