The HDMI TX controller support different PHYs whose programming
interface can vary significantly, especially with vendor PHYs that are
not provided by Synopsys. To support them, create a PHY operation
structure that can be provided by the platform glue layer. The existing
PHY handling code (limited to Synopsys PHY support) is refactored into a
set of default PHY operations that are used automatically when the
platform glue doesn't provide its own operations.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170305233615.11993-1-laurent.pinchart+renesas@ideasonboard.com

When powering the PHY up we need to wait for the PLL to lock. This is
done by polling the TX_PHY_LOCK bit in the HDMI_PHY_STAT0 register
(interrupt-based wait could be implemented as well but is likely
overkill). The bit is asserted when the PLL locks, but the current code
incorrectly waits for the bit to be deasserted. Fix it, and while at it,
replace the udelay() with a sleep as the code never runs in
non-sleepable context.

To be consistent with the power down implementation move the poll loop
to the power off function.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170305233557.11945-1-laurent.pinchart+renesas@ideasonboard.com

The PHY requires us to wait for the PHY to switch to low power mode
after deasserting TXPWRON and before asserting PDDQ in the power down
sequence, otherwise power down will fail.

The PHY power down can be monitored though the TX_READY bit, available
through I2C in the PHY registers, or the TX_PHY_LOCK bit, available
through the HDMI TX registers. As the two are equivalent, let's pick the
easier solution of polling the TX_PHY_LOCK bit.

The power down code is currently duplicated in multiple places. To avoid
spreading multiple calls to a TX_PHY_LOCK poll function, we have to
refactor the power down code and group it all in a single function.

Tests showed that one poll iteration was enough for TX_PHY_LOCK to
become low, without requiring any additional delay. Retrying the read
five times with a 1ms to 2ms delay between each attempt should thus be
more than enough.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170305233539.11898-1-laurent.pinchart+renesas@ideasonboard.com

If the input pixel format is not RGB, the CSC must be enabled in order to
provide valid pixel to DVI sinks.
This patch removes the hdmi only dependency on the CSC enabling.
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-4-laurent.pinchart+renesas@ideasonboard.com

The color space converter isn't part of the PHY, move its configuration
out of PHY code.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-3-laurent.pinchart+renesas@ideasonboard.com

Most of the hdmi_phy_test_*() functions are unused. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Tested-by: NNickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-2-laurent.pinchart+renesas@ideasonboard.com

I'm torn on whether drm_minor really should be here or somewhere else.
Maybe with more clarity after untangling drmP.h more this is easier to
decide, for now I've put a FIXME comment right next to it. Right now
we need struct drm_minor for the inline drm_file type helpers, and so
it does kinda make sense to have them here.

Next patch will kerneldoc-ify the entire pile.
Reviewed-by: NGustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-10-daniel.vetter@ffwll.ch

This was originally added by David Herrmann for range checks, but
entirely unused. It confused me, so let's remove it.

Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-9-daniel.vetter@ffwll.ch

It's not just file ops, but drm_file stuff in general. This is prep
work to extracting a drm_file.h header in the next patch.
Reviewed-by: NGustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-8-daniel.vetter@ffwll.ch

Worst case if the hw can't support completion signalling in a
race-free way we want the event to be too late, not too early.

Text adapted from a proposal from Laurent - the other side of how to
make hw work correctly where it's possible is imo already sufficiently
documented.

v2: Review from Laurent.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-7-daniel.vetter@ffwll.ch

An easy one as a drive-by.
Reviewed-by: NGustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-6-daniel.vetter@ffwll.ch

Just another step in finally making drmP.h obsolete.
Reviewed-by: NGustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-5-daniel.vetter@ffwll.ch

And remove the semi-kernel-doc stuff, to make sure no one uses this.
Reviewed-by: NGustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-4-daniel.vetter@ffwll.ch

Plus a little bit more documentation.

v2: Untangle the missing forward decls to make drm_prime|gem.h
free-standing.
Reviewed-by: NGustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-3-daniel.vetter@ffwll.ch

At least radeon, amdgpu and nouveau should be converted. We have
patches for i915 already.

v2: Spelling (Sean).
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-2-daniel.vetter@ffwll.ch

drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so it's not necessary to call drm_debugfs_remove_files().

Cc: airlied@linux.ie
Cc: kraxel@redhat.com
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307204924.1002-4-noralf@tronnes.org

[ kraxel: solved conflict ]
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Remove the .debugfs_cleanup() callback now that all the users are gone.
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307204924.1002-3-noralf@tronnes.org

Move the contents of msm_debugfs_cleanup() to msm_drm_uninit() to free
up the drm_driver->debugfs_cleanup callback. Also remove the
mdp_kms_funcs->debugfs_cleanup callback which has no users.

Cc: robdclark@gmail.com
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>
Acked-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307204924.1002-2-noralf@tronnes.org

Gabriel Krisman reported these warnings when building the documentation:

 ./drivers/gpu/drm/drm_dp_helper.c:1165: warning: No description found
for parameter 'crtc'
./drivers/gpu/drm/drm_dp_helper.c:1166: warning: No description found
for parameter 'crtc'
Reported-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307203511.14258-1-tomeu.vizoso@collabora.com

Just use kmem_cache instead of rolling
our own, limited implementation.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1488377348-5006-1-git-send-email-kraxel@redhat.com

Call qxl_add_monitors_config_modes() unconditionally.  Do all sanity
checks in that function.

Fix sanity checks.  monitors_config is the current monitor
configuration, whereas client_monitors_config is the configuration
requested by the spice client.  So when filling the mode list, based on
the spice client request, we need to look at
client_monitors_config->count not monitors_config->count.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Reviewed-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-5-git-send-email-kraxel@redhat.com

Try to read the client monitors config at driver load time, even without
explicit notification.  So in case that info was filled before the driver
loaded and we've missed the notifications because of that the settings
will still be used.

With that place we now have to take care to properly handle a empty client
monitors config, so we don't trip over an uninitialized client monitors
config.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Reviewed-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-4-git-send-email-kraxel@redhat.com

When reading the monitor config fails, don't retry forever.  If it fails
ten times in a row just give up to avoid the driver hangs.  Also add a
small delay after each attempt, so the host has a chance to complete a
partial update.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Reviewed-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-3-git-send-email-kraxel@redhat.com

very old qxl hardware revisions (predating qxl ksm support by a few
years) supported a fixed list of video modes only.  The list is still
provided by the virtual hardware, for backward compatibility reasons.

The qxl kms driver never ever looks at it, except for dumping it to
the kernel log at load time in case debug logging is enabled.  Drop
that pointless code.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Reviewed-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488363154-6889-2-git-send-email-kraxel@redhat.com

If fbdev emulation is disabled, the QXL shutdown path will try to clean
a framebuffer that wasn't initialized, hitting the Oops below.  The
problem is that even when FBDEV_EMULATION is disabled we allocate the
qfbdev strutucture, but we don't initialize it.  The fix is to stop
allocating the memory, since it won't be used.  This allows the existing
verification in the cleanup hook to do it's job preventing the oops.

Now that we don't allocate the unused fbdev structure, we need to be
careful when dereferencing it in the PM suspend hook.

[   24.284684] BUG: unable to handle kernel NULL pointer dereference at 00000000000002e0
[   24.285627] IP: mutex_lock+0x18/0x30
[   24.286049] PGD 78cdf067
[   24.286050] PUD 7940f067
[   24.286344] PMD 0
[   24.286649]
[   24.287072] Oops: 0002 [#1] SMP
[   24.287422] Modules linked in: qxl
[   24.287806] CPU: 0 PID: 2328 Comm: bash Not tainted 4.10.0-rc5+ #97
[   24.288515] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-20161025_171302-gandalf 04/01/2014
[   24.289681] task: ffff88007c4c0000 task.stack: ffffc90001b58000
[   24.290354] RIP: 0010:mutex_lock+0x18/0x30
[   24.290812] RSP: 0018:ffffc90001b5bcb0 EFLAGS: 00010246
[   24.291401] RAX: 0000000000000000 RBX: 00000000000002e0 RCX: 0000000000000000
[   24.292209] RDX: ffff88007c4c0000 RSI: 0000000000000001 RDI: 00000000000002e0
[   24.292987] RBP: ffffc90001b5bcb8 R08: fffffffffffffffe R09: 0000000000000001
[   24.293797] R10: ffff880078d80b80 R11: 0000000000011400 R12: 0000000000000000
[   24.294601] R13: 00000000000002e0 R14: ffffffffa0009c28 R15: 0000000000000060
[   24.295439] FS:  00007f30e3acbb40(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000
[   24.296364] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   24.296997] CR2: 00000000000002e0 CR3: 0000000078c7b000 CR4: 00000000000006f0
[   24.297813] Call Trace:
[   24.298097]  drm_framebuffer_cleanup+0x1f/0x70
[   24.298612]  qxl_fbdev_fini+0x68/0x90 [qxl]
[   24.299074]  qxl_modeset_fini+0xd/0x30 [qxl]
[   24.299562]  qxl_pci_remove+0x22/0x50 [qxl]
[   24.300025]  pci_device_remove+0x34/0xb0
[   24.300507]  device_release_driver_internal+0x150/0x200
[   24.301082]  device_release_driver+0xd/0x10
[   24.301587]  unbind_store+0x108/0x150
[   24.301993]  drv_attr_store+0x20/0x30
[   24.302402]  sysfs_kf_write+0x32/0x40
[   24.302827]  kernfs_fop_write+0x108/0x190
[   24.303269]  __vfs_write+0x23/0x120
[   24.303678]  ? security_file_permission+0x36/0xb0
[   24.304193]  ? rw_verify_area+0x49/0xb0
[   24.304636]  vfs_write+0xb0/0x190
[   24.305004]  SyS_write+0x41/0xa0
[   24.305362]  entry_SYSCALL_64_fastpath+0x1a/0xa9
[   24.305887] RIP: 0033:0x7f30e31d9620
[   24.306285] RSP: 002b:00007ffc54b47e68 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[   24.307128] RAX: ffffffffffffffda RBX: 00007f30e3497600 RCX: 00007f30e31d9620
[   24.307928] RDX: 000000000000000d RSI: 0000000000da2008 RDI: 0000000000000001
[   24.308727] RBP: 000000000070bc60 R08: 00007f30e3498760 R09: 00007f30e3acbb40
[   24.309504] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000001
[   24.310295] R13: 0000000000000000 R14: 0000000000000000 R15: 00007ffc54b47f34
[   24.311095] Code: 0e 01 e9 7b fe ff ff 66 90 66 2e 0f 1f 84 00 00 00 00 00
55 48 89 e5 53 48 89 fb e8 83 e8 ff ff 65 48 8b 14 25 40 c4 00 00 31 c0 <3e>
48 0f b1 13 48 85 c0 74 08 48 89 df e8 66 fd ff ff 5b 5d c3
[   24.313182] RIP: mutex_lock+0x18/0x30 RSP: ffffc90001b5bcb0
[   24.313811] CR2: 00000000000002e0
[   24.314208] ---[ end trace 29669c1593cae14b ]---
Signed-off-by: NGabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227203330.18542-1-krisman@collabora.co.ukSigned-off-by: NGerd Hoffmann <kraxel@redhat.com>

Fixes the following link error when CONFIG_DRM_ANALOGIX_DP is not defined:

ERROR: "analogix_dp_start_crc" [drivers/gpu/drm/rockchip/rockchipdrm.ko] undefined!
ERROR: "analogix_dp_stop_crc" [drivers/gpu/drm/rockchip/rockchipdrm.ko] undefined!

Fixes: 3190e58d ("drm/rockchip: Implement CRC debugfs API")
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>

This patch fixes the following compilation error when CONFIG_DEBUG_FS is not defined.

../drivers/gpu/drm/drm_dp_helper.c: In function ‘drm_dp_aux_crc_work’:
../drivers/gpu/drm/drm_dp_helper.c:1029:13: error: ‘struct drm_crtc’ has no member named ‘crc’
../drivers/gpu/drm/drm_dp_helper.c:1031:12: error: ‘struct drm_crtc’ has no member named ‘crc’
  make[4]: *** [drivers/gpu/drm/drm_dp_helper.o] Error 1
  make[4]: *** Waiting for unfinished jobs....

Fixes: 79c1da7c ("drm/dp: add helpers for capture of frame CRCs")
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: NEmil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>

Implement the .set_crc_source() callback and call the DP helpers
accordingly to start and stop CRC capture.

This is only done if this CRTC is currently using the eDP connector.

v3: Remove superfluous check on rockchip_crtc_state->output_type

v6: Remove superfluous variable
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: NMark Yao <mark.yao@rock-chips.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-5-tomeu.vizoso@collabora.com

Add two simple functions that just take the drm_dp_aux from our struct
and calls the corresponding DP helpers with it.

v6: Pass to the DP helper the drm_crtc of the current connector (Sean Paul)
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-4-tomeu.vizoso@collabora.com

Adds helpers for starting and stopping capture of frame CRCs through the
DPCD. When capture is on, a worker waits for vblanks and retrieves the
frame CRC to put it in the queue on the CRTC that is using the
eDP connector, so it's passed to userspace.

v2: Reuse drm_crtc_wait_one_vblank
    Update locking, as drm_crtc_add_crc_entry now takes the lock

v3: Don't call wake_up_interruptible directly, that's now done in
    drm_crtc_add_crc_entry.

v4: Style fixes (Sean Paul)
    Reworked retry of CRC reads (Sean Paul)
    Flush worker after stopping CRC generationa (Sean Paul)

v5: Move back to make the retry explicitly once

v6: Set and use the drm_crtc backpointer (Sean Paul)
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-3-tomeu.vizoso@collabora.com

This backpointer allows DP helpers to access the crtc it's currently
being used for.

v6: Have the backpointer be to drm_crtc (Sean Paul)
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-2-tomeu.vizoso@collabora.com

There are new iterator macros that annotate whether the new or old
state should be used. This is better than using a state that depends on
whether it's called before or after swap. For clarity, also rename the
variables from $obj_state to (old,new)_$obj_state as well.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487256430-7625-6-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

This is a straightforward conversion that converts all the users of
get_existing_state in atomic core to use get_old_state or get_new_state

Changes since v1:
- Fix using the wrong state in drm_atomic_helper_update_legacy_modeset_state.
Changes since v2:
- Use the correct state in disable_outputs()
Changes since v3:
- Rebase for link status training.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/df91a9f9-005e-bcbd-1f74-03c38e1e21dd@linux.intel.comReviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

After atomic commit, these macros should be used in place of
get_existing_state. Also after commit get_xx_state should no longer
be used because it may not have the required locks.

The calls to drm_atomic_get_existing_$obj_state should no longer be
used, and converted over to these new calls.

Changes since v1:
- Expand commit message.
- Deprecate get_existing_*_state functions in the documentation.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487256430-7625-4-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

This function becomes a lot simpler when having passed both the old and
new state to it. Looking at all callers, it seems that old_plane_state
is never NULL so the check can be dropped.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487256430-7625-3-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

There are new iterator macros that annotate whether the new or old
state should be used. This is better than using a state that depends on
whether it's called before or after swap. For clarity, also rename the
variables from $obj_state to (old,new)_$obj_state as well.

Changes since v1:
- Use old/new_*_state for variable names as much as possible. (pinchartl)
- Expand commit message.
Changes since v2:
- Rebase on top of link training patches.
- free -> cleanup (pinchartl)
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/aafa0d4d-474d-441f-3685-fa6c042ef37e@linux.intel.comTested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The THC63LVDM83D is a transparent LVDS encoder. Unlike dumb LVDS
encoders it can be controlled through a few pins (power down, LVDS
swing, clock edge selection) and requires power supplies. However, on
several boards where the device is used neither the control pins nor the
power supply are controllable.

To avoid developing a separate device-specific driver add a
"thine,thc63lvdm83d" compatible entry to the lvds-encoder driver. This
will allow supporting many THC63LVDM83D-based boards easily, while
allowing future development of an thc63lvdm83d driver when needed
without breaking backward compatibility.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-5-laurent.pinchart+renesas@ideasonboard.com

The ADV7123 is a transparent VGA DAC. Unlike dumb VGA DACs it can be
controlled through a power save pin, and requires a power supply.
However, on most boards where the device is used neither the power save
signal nor the power supply are controllable.

To avoid developing a separate device-specific driver add an
"adi,adv7123" compatible entry to the dumb-vga-dac driver. This will
allow supporting most ADV7123-based boards easily, while allowing future
development of an adv7123 driver when needed without breaking backward
compatibility.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-4-laurent.pinchart+renesas@ideasonboard.com

The LVDS encoder driver is a DRM bridge driver that supports the
parallel to LVDS encoders that don't require any configuration. The
driver thus doesn't interact with the device, but creates an LVDS
connector for the panel and exposes its size and timing based on
information retrieved from DT.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NDaniel Vetter <daniel@ffwll.ch>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-3-laurent.pinchart+renesas@ideasonboard.com

The DT bindings support parallel to LVDS encoders that don't require any
configuration, similarly to the dumb VGA DAC DT bindings.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-2-laurent.pinchart+renesas@ideasonboard.com