The problem that the set timings code contains the call of Davinci
platform function davinci_aemif_setup_timing() which is not
accessible if kernel is built for another platform like Keystone.

The Keysone platform is going to use TI AEMIF driver.
If TI AEMIF is used we don't need to set timings and bus width.
It is done by AEMIF driver.

To get rid of davinci-nand driver dependency on aemif platform code
we moved aemif code to davinci platform.

The platform AEMIF code (aemif.c) has to be removed once Davinci
will be converted to DT and use ti-aemif.c driver.
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
[nsekhar@ti.com: fixed checkpatch error and a build breakage due to
		 missing include, rebased onto l2-mtd/master]
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patch moves the at24.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.

It also fixes the following checkpatch warning:

    WARNING: please, no space before tabs
    #436: FILE: include/linux/platform_data/at24.h:31:
    + * ^Iu8 *mac_addr = ethernet_pdata->mac_addr;$
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

"struct davinci_uart_config" was introduced to specify
UART ports brought out or enabled on the board. But
none of the boards use it for that purpose and we are
not going to add anymore board files, so remove the
structure.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Suggested-by: NSekhar Nori <nsekhar@ti.com>
[nsekhar@ti.com: split patch to remove davinci_serial_setup_clk()
		 changes.]
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Without this patch, da8xx_register_spi() registers the SPI board info,
the SPI controller, and sets its number of chipselect to the size of the
static spi_board_info array. This is bad because a SPI board info may
declare devices for different SPI buses, and because other code can also
call spi_register_board_info() (e.g. a daughter board might provide
additional SPI devices).

This patch removes the spi_register_board_info() call from
da8xx_register_spi(), renames this last one to da8xx_register_spi_bus()
to be more explicit, takes the number of chipselect as a function
parameter, and updates the impacted board-da8{3,5}0-evm.c, and
board-mityomapl138.c files accordingly. It also sets the SPI platform
data static, as it doesn't need to be exported.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
[nsekhar@ti.com: fixed conflicts with v3.7-rc7, converted to use pr_warn(),
modified print messages to use __func__]
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.

This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html

Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the davinci include directories
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com

Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSekhar Nori <nsekhar@ti.com>

Rather than using DaVinci specific davinci_soc_info based
restart hook, use the restart hook available in the machine
descriptor instead.

Tested on DM365 and AM18x EVMs.

v2:
Changed to use restart hook in machine descriptor
per Russell's comment.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Recall the recently added prefix requirements:
 * "NAND_" for flags in nand.h, used in nand_chip.options
 * "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
        or in nand_bbt_descr.options

Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.

Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

This patch works with the following three flags from two headers (nand.h
and bbm.h):
  (1) NAND_USE_FLASH_BBT (nand.h)
  (2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
  (3) NAND_BBT_NO_OOB (bbm.h)

These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.

This patch accomplishes the following:
  * eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
  * move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h

It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.

I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>

Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).

To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.

Hope people are OK with tiny include file.

Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current board configurations involving the MityDSP-L138 and MityARM-1808
only have one attached PHY, but it's address may not be the same.  Default
the behavior to auto-probe for the PHY and use the first one found.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

For the MityDSP-L138/MityARM-1808 SOMS, the NAND controller id (which needs
to correspond to the chipselect, and is used for controlling the HW ECC
computation) is not correct.  Fix it.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patch adds support for accessing the on board SPI NOR FLASH
device for MityDSP-L138 and MityARM-1808 SoMs.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Tested-by: NMichael Williamson <michael.williamson@criticallink.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

For the MityDSP-L138/MityARM-1808 SoMs, the speed grade can be determined
from the part number string read from the factory configuration block on
the on-board I2C PROM.  Configure the maximum CPU speed based on this
information.

This patch was tested using a MityDSP-L138 and MityARM-1808 at various
speedgrades.  Also, for code coverage, a bogus configuration was tested
as well as a configuration having an unknown part number.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Tested-by: NMichael Williamson <michael.williamson@criticallink.com>
Reviewed-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Some boards that were added after the mass io_pgoffst/io_physio
removal, and were not updated in the original patch.  Fixup here.

c.f. original io_pgoffst/io_physio removal
     commit 6451d778Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Most of the regulator data structures are local to the
board file, but not made static. Fix this.

Also make the nand partition table static.

This gets rid of all the sparse warnings for this file.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

For the MityDSP-L138/MityARM-1808 SOMS, read the factory assigned
MAC address from the onboard I2C EPROM and assign it to the emac
device during platform initialization.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch removes davinci architecture code that has now been rendered
useless by the previous patches in the MDIO separation series.

In addition, the earlier phy_mask definitions have been replaced with
corresponding phy_id definitions.
Signed-off-by: NCyril Chemparathy <cyril@ti.com>
Tested-by: NMichael Williamson <michael.williamson@criticallink.com>
Tested-by: NCaglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds the i2c0 bus and attached devices to the MityDSP-L138
and MityARM-1808 davinci SoM.  Included is a TPS65023 voltage regulator
needed for power management and a small 24c02 EPROM that contains
factory configuration data.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system
on Module (SOM) under the machine name "mityomapl138".  These SOMs are based
on the da850 davinci CPU architecture.  Information on these SOMs may be
found at http://www.mitydsp.com.

Basic support for the console UART, NAND, and EMAC (MII interface) is
included in this patch.
Signed-off-by: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>