When the rate control algorithms are built-in, their exit
functions can be called from mac80211's init function so
they cannot be marked __exit.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mattias Nissler's "clean up rate selection" patch incorrectly changes
the behavior of txrate setting in sta_info. This patch backs out parts
of the rate selection consolidation in order to fix this issue for now.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch changes mac80211's Kconfig/Makefile to:
 * select between the PID and the SIMPLE rate control
   algorithm as default
 * always allow tri-state for the rate control algorithms,
   building those that are selected 'y' into the mac80211
   module (if that is a module, otherwise all into the kernel)
 * force the default rate control algorithm to be built into
   mac80211

It also makes both rate control algorithms proper modules again
with MODULE_LICENSE etc.

Only if EMBEDDED is the user allowed to select "NONE" as default
which will cause no algorithm to be selected, this will work
only when the driver brings one itself (e.g. iwlwifi drivers).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move some code out of rc80211_simple since it's probably needed for all rate
selection algorithms, and fix iwlwifi accordingly. While at it, clean up the
rate_control_get_rate() interface.
Signed-off-by: NStefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Too frequently people do not have module autoloading enabled
or fail to install the rate control module correctly, hence
their hardware probing fails due to no rate control algorithm
being available. This makes the 'simple' algorithm built into
the mac80211 module unless EMBEDDED is enabled in which case
it can be disabled (eg. if the wanted driver requires another
rate control algorithm.)
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is nicer than the MAC_FMT stuff.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ioctls

 * PRISM2_PARAM_STA_ANTENNA_SEL
 * PRISM2_PARAM_TX_POWER_REDUCTION
 * PRISM2_PARAM_DEFAULT_WEP_ONLY

are not used by hostapd or wpa_supplicant.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mac80211 is built into the kernel it needs to init earlier
so that device registrations are run after it has initialised.
The same applies to rate control algorithms.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These aren't used anywhere (hostapd, wpa_supplicant) and until we
have a proper interface to the rate control algorithms they don't
make much sense either since e.g. rc80211_lowest won't honour them.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The initial rate for STA's using rc80211_simple is set to the last
rate in the rate table. For situations for which the signal is weak,
the rate may be too high for authentication and association. Although
the rc80211_simple module will adjust the speed, the response may not
be fast enough for a successful connection. This modification sets the
initial rate to the lowest supported value.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export various mac80211 internal variables through debugfs.
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add mac80211, the IEEE 802.11 software MAC layer.
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>