When a signal interrupts a Configure Endpoint command, the cmd_completion used
in xhci_configure_endpoint() is not re-initialized and the
wait_for_completion_interruptible_timeout() will return failure. Initialize
cmd_completion in xhci_configure_endpoint().
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Naming consistency with other USB HCDs.
Signed-off-by: NAlex Chiang <achiang@hp.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.

After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.

This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-by: NColin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When isochronous URBs are shorter than one frame and when more than one
ITD in a frame has been completed before the interrupt can be handled,
scan_periodic() completes the URBs in the order in which they are found
in the descriptor list.  Therefore, the descriptor list must contain the
ITDs in the correct order, i.e., a new ITD must be linked in after any
previous ITDs of the same endpoint.

This should fix garbled capture data in the USB audio drivers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-by: NColin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c_board_info doesn't contain a member called name. i2c_register_client
call does not exist.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Texas Instruments DA8xx/OMAP-L1x OHCI glue layer.

This OHCI implementation is not without quirks: there's only one physical port
despite the root hub reporting two; the port's power control and over-current
status bits are not connected to any pins, however, at least on the DA830 EVM
board, those signals are connected via GPIO, thus the provision was made for
overriding the OHCI port power and over-current bits at the board level...
Signed-off-by: NMikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

DPLL5 programming was moved out of this file before submission.
Update the TODO list in the comments to reflect this
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current driver reduces the interrupt threshold to 1 microframe.
This was an accidental change and is not really required.
The default of 8 microframes will do just fine. So change it back.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Kill these compile warnings:
CC [M]  drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-dbg.c:45: warning: 'dbg_hcs_params' defined but not used
drivers/usb/host/ehci-dbg.c:89: warning: 'dbg_hcc_params' defined but not used
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

According "5.3.6 Capability Parameters (HCCPARAMS)" of xHCI rev0.96 spec,
value of xECP register indicates a relative offset, in 32-bit words,
from Base to the beginning of the first extended capability.
The wrong calculation will cause BIOS handoff fail (not handoff from BIOS)
in some platform with BIOS USB legacy sup support.
Signed-off-by: NEdward Shao <laface.tw@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reduces string space a bit
Neaten a macro redefine of dbg
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the HDC driver writes the data to the transfer buffers it pollutes
the D-cache (unlike DMA drivers where the device writes the data). If
the corresponding pages get mapped into user space, there are no
additional cache flushing operations performed and this causes random
user space faults on architectures with separate I and D caches
(Harvard) or those with aliasing D-cache.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Cc: Matthew Dharm <mdharm-kernel@one-eyed-alien.net>
Cc: Greg KH <greg@kroah.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The configuration Option USB_HCD_DMA is not reachable in KConfig so
this piece of Code is effectively dead and useless. Remove it to avoid
confusion.
Signed-off-by: NChristoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The match_table field of the struct of_device_id is constant in <linux/of_platform.h>
so it is worth to make the initialization data also constant.

The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
	struct I1 {
	  ...
	  const struct I2 *x;
	  ...
	};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
	struct I1 y = {
	  .x = E,
	};
@c@
identifier r.I2;
identifier s.E;
@@
	const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+	const
	struct I2 E[] = ...;
// </smpl>
Signed-off-by: NNémeth Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When hardware is removed on a Stratus, the system may crash like this:

ACPI: PCI interrupt for device 0000:7c:00.1 disabled
Trying to free nonexistent resource <00000000a8000000-00000000afffffff>
Trying to free nonexistent resource <00000000a4800000-00000000a480ffff>
uhci_hcd 0000:7e:1d.0: remove, state 1
usb usb2: USB disconnect, address 1
usb 2-1: USB disconnect, address 2
Unable to handle kernel paging request at 0000000000100100 RIP:
 [<ffffffff88021950>] :uhci_hcd:uhci_scan_schedule+0xa2/0x89c

 #4 [ffff81011de17e50] uhci_scan_schedule at ffffffff88021918
 #5 [ffff81011de17ed0] uhci_irq at ffffffff88023cb8
 #6 [ffff81011de17f10] usb_hcd_irq at ffffffff801f1c1f
 #7 [ffff81011de17f20] handle_IRQ_event at ffffffff8001123b
 #8 [ffff81011de17f50] __do_IRQ at ffffffff800ba749

This occurs because an interrupt scans uhci->skelqh, which is
being freed. We do the right thing: disable the interrupts in the
device, and do not do any processing if the interrupt is shared
with other source, but it's possible that another CPU gets
delayed somewhere (e.g. loops) until we started freeing.

The agreed-upon solution is to wait for interrupts to play out
before proceeding. No other bareers are neceesary.

A backport of this patch was tested on a 2.6.18 based kernel.
Testing of 2.6.32-based kernels is under way, but it takes us
forever (months) to turn this around. So I think it's a good
patch and we should keep it.

Tracked in RH bz#516851
Signed-Off-By: NPete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Randy Dunlap reported this error when compiling the xHCI driver:

linux-next-20100104/drivers/usb/host/xhci.h:1214:
sorry, unimplemented: inlining failed in call to 'xhci_get_slot_state': function body not available

The xhci_get_slot_state() function belongs in xhci-dbg.c, since it
involves debugging internal xHCI structures.  However, it is only used in
xhci-hcd.c.  Some toolchains may have issues since the inlined function
body is not in the xhci.h header file.  Remove the inline keyword to avoid
this.
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

urb_priv->tds has type struct td **, not struct td *, so the
elements of the array should have pointer type, not structure type.

Convert kzalloc to kcalloc as well.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@

  x =
  <+...sizeof(
- T
+ *x
  )...+>
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OMAP3 has three HS USB ports so it can have three different regulator
for each PHY connected to each port.

Currently these regulators are assumed to be optional and driver doesn't
fail but continue with the initialization if it doesn't get any regulators.

Regulator supply names has to be mapped in board files as 'hsusbN' where
'N' is port number and can be {0, 1 ,2}.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added missing kfree() in ehci_hcd_omap_remove().
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It's really the wireless speed, so rename the thing to make
more sense.  Based on a recommendation from David Vrabel

Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use kzalloc rather than kcalloc(1,...)

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
          ...)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

xhci_add_endpoint() is used in the reset path. It must
use GFP_NOIO to avoid a possible deadlock.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Acked-by: NSarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use platform_get_resource() to fetch the memory resource and
resource_size() for calculate the length.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use resource_size().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use resource_size().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI FSL controller preserve its state during sleep mode, so nothing
fancy needs to be done.

Though, during 'deep sleep' mode (as found in MPC831x CPUs) the
controller turns off and needs to be reinitialized upon resume.

This patch adds support for hibernation and resuming after deep sleep.
Based on Dave Liu and Jerry Huang's work[1].

[1] http://www.bitshrine.org/gpp/linux-fsl-2.6.24.3-MPC8315ERDB-usb-power-mangement.patchSigned-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes following warnings:

ehci-fsl.c:43:5: warning: symbol 'usb_hcd_fsl_probe' was not declared. Should it be static?
ehci-fsl.c:150:6: warning: symbol 'usb_hcd_fsl_remove' was not declared. Should it be static?
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fix audio record functionality for some Full speed sound blaster devices.
Issue: Sometimes transaction complete indication is coming from HW one frame later.
Solution: If scan_periodic process now frame or previous frame now-1 and sitd transaction
is not finished yet, exit scan_periodic function and check the same transaction in the next frame.
Signed-off-by: NDimitry Epshtein <dima@marvell.com>
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Sometimes disable_periodic() stop scan_periodic before than free_cached_itd_list() was called.
In such case USB Host stacked during disconnect operation
Solution: add call of free_cached_itd_list() function in disable_periodic()
Signed-off-by: NDimitry Epshtein <dima@marvell.com>
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a new host controller driver method, reset_device(), that the USB core
will use to notify the host of a successful device reset.  The call may
fail due to out-of-memory errors; attempt the port reset sequence again if
that happens.  Update hub_port_init() to allow resetting a configured
device.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a USB device is reset, the xHCI hardware must know, in order to match
the device state and disable all endpoints except control endpoint 0.
Issue a Reset Device command after a USB device is successfully reset.
Wait on the command to finish, and then cache or free the disabled
endpoint rings.

There are four different USB device states that the xHCI hardware tracks:
 - disabled/enabled - device connection has just been detected,
 - default - the device has been reset and has an address of 0,
 - addressed - the device has a non-zero address but no configuration has
   been set,
 - configured - a set configuration succeeded.

The USB core may issue a port reset when a device is in any state, but the
Reset Device command will fail for a 0.96 xHC if the device is not in the
addressed or configured state.  Don't consider this failure as an error,
but don't free any endpoint rings if this command fails.

A storage driver may request that the USB device be reset during error
handling, so use GPF_NOIO instead of GPF_KERNEL while allocating memory
for the Reset Device command.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add the hub emulation code to allow ports on an xHCI root hub to be
disabled.  Add the code to clear the port enabled/disabled bit, and clear
the port enabled/disabled change bit.  Like EHCI, the port cannot be
enabled by setting the port enabled/disabled bit.  Instead, a port is
enabled by the host controller after a reset.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Refactor the code to clear the port change bits in the port status
register.  All port status change bits are write one to clear.

Remove a redundant port status read that was supposed to unblock any
posted writes.  We read the port after the write to get the updated status
for debugging, so the port read after that is unnecessary.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All commands that can be issued to the xHCI hardware can come back with
vendor-specific "informational" completion codes.  These are to be treated
like a successful completion code.  Refactor out the code to test for the
range of these codes and print debugging messages.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The xhci_command structure is the basic structure for issuing commands to
the xHCI hardware.  It contains a struct completion (so that the issuing
function can wait on the command), command status, and a input context
that is used to pass information to the hardware.  Not all commands need
the input context, so make it optional to allocate.  Allow
xhci_free_container_ctx() to be passed a NULL input context, to make
freeing the xhci_command structure simple.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Refactor out the code to cache or free endpoint rings from recently
dropped or disabled endpoints.  This code will be used by a new function
to reset a device and disable all endpoints except control endpoint 0.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If we fail to queue an evaluate context command or a configure endpoint
command to the command ring in xhci_configure_endpoint(), we need to
remove the xhci_command structure from the device's command list before
returning.  If the command is left on the command list, it will sit there
indefinitely, blocking commands submitted after this fails.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On various mxc boards, the intial ULPI reads resulted in a timeout
which prevented the transceiver to be identified and thus the ehci
device to be probed.

Initializing the hardware lines connected to the transceiver (through
pdata->init call) before actually enabling clocks and configuring
registers in the devices fixes this problem.
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>