Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 13 3月, 2009 13 次提交
  3. 10 3月, 2009 4 次提交
  5. 07 3月, 2009 5 次提交
  7. 02 3月, 2009 1 次提交
  9. 01 3月, 2009 2 次提交
  11. 28 2月, 2009 1 次提交
  13. 27 2月, 2009 1 次提交
  15. 26 2月, 2009 3 次提交
    • J
      block: reduce stack footprint of blk_recount_segments() · 1e428079
      由 Jens Axboe 提交于 
      blk_recalc_rq_segments() requires a request structure passed in, which
we don't have from blk_recount_segments(). So the latter allocates one on
the stack, using > 400 bytes of stack for that. This can cause us to spill
over one page of stack from ext4 at least:

 0)     4560     400   blk_recount_segments+0x43/0x62
 1)     4160      32   bio_phys_segments+0x1c/0x24
 2)     4128      32   blk_rq_bio_prep+0x2a/0xf9
 3)     4096      32   init_request_from_bio+0xf9/0xfe
 4)     4064     112   __make_request+0x33c/0x3f6
 5)     3952     144   generic_make_request+0x2d1/0x321
 6)     3808      64   submit_bio+0xb9/0xc3
 7)     3744      48   submit_bh+0xea/0x10e
 8)     3696     368   ext4_mb_init_cache+0x257/0xa6a [ext4]
 9)     3328     288   ext4_mb_regular_allocator+0x421/0xcd9 [ext4]
10)     3040     160   ext4_mb_new_blocks+0x211/0x4b4 [ext4]
11)     2880     336   ext4_ext_get_blocks+0xb61/0xd45 [ext4]
12)     2544      96   ext4_get_blocks_wrap+0xf2/0x200 [ext4]
13)     2448      80   ext4_da_get_block_write+0x6e/0x16b [ext4]
14)     2368     352   mpage_da_map_blocks+0x7e/0x4b3 [ext4]
15)     2016     352   ext4_da_writepages+0x2ce/0x43c [ext4]
16)     1664      32   do_writepages+0x2d/0x3c
17)     1632     144   __writeback_single_inode+0x162/0x2cd
18)     1488      96   generic_sync_sb_inodes+0x1e3/0x32b
19)     1392      16   sync_sb_inodes+0xe/0x10
20)     1376      48   writeback_inodes+0x69/0xb3
21)     1328     208   balance_dirty_pages_ratelimited_nr+0x187/0x2f9
22)     1120     224   generic_file_buffered_write+0x1d4/0x2c4
23)      896     176   __generic_file_aio_write_nolock+0x35f/0x393
24)      720      80   generic_file_aio_write+0x6c/0xc8
25)      640      80   ext4_file_write+0xa9/0x137 [ext4]
26)      560     320   do_sync_write+0xf0/0x137
27)      240      48   vfs_write+0xb3/0x13c
28)      192      64   sys_write+0x4c/0x74
29)      128     128   system_call_fastpath+0x16/0x1b

Split the segment counting out into a __blk_recalc_rq_segments() helper
to avoid allocating an onstack request just for checking the physical
segment count.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
      1e428079
    • P
      rcu: Teach RCU that idle task is not quiscent state at boot · a6826048
      由 Paul E. McKenney 提交于 
      This patch fixes a bug located by Vegard Nossum with the aid of
kmemcheck, updated based on review comments from Nick Piggin,
Ingo Molnar, and Andrew Morton.  And cleans up the variable-name
and function-name language.  ;-)

The boot CPU runs in the context of its idle thread during boot-up.
During this time, idle_cpu(0) will always return nonzero, which will
fool Classic and Hierarchical RCU into deciding that a large chunk of
the boot-up sequence is a big long quiescent state.  This in turn causes
RCU to prematurely end grace periods during this time.

This patch changes the rcutree.c and rcuclassic.c rcu_check_callbacks()
function to ignore the idle task as a quiescent state until the
system has started up the scheduler in rest_init(), introducing a
new non-API function rcu_idle_now_means_idle() to inform RCU of this
transition.  RCU maintains an internal rcu_idle_cpu_truthful variable
to track this state, which is then used by rcu_check_callback() to
determine if it should believe idle_cpu().

Because this patch has the effect of disallowing RCU grace periods
during long stretches of the boot-up sequence, this patch also introduces
Josh Triplett's UP-only optimization that makes synchronize_rcu() be a
no-op if num_online_cpus() returns 1.  This allows boot-time code that
calls synchronize_rcu() to proceed normally.  Note, however, that RCU
callbacks registered by call_rcu() will likely queue up until later in
the boot sequence.  Although rcuclassic and rcutree can also use this
same optimization after boot completes, rcupreempt must restrict its
use of this optimization to the portion of the boot sequence before the
scheduler starts up, given that an rcupreempt RCU read-side critical
section may be preeempted.

In addition, this patch takes Nick Piggin's suggestion to make the
system_state global variable be __read_mostly.

Changes since v4:

o	Changes the name of the introduced function and variable to
	be less emotional.  ;-)

Changes since v3:

o	WARN_ON(nr_context_switches() > 0) to verify that RCU
	switches out of boot-time mode before the first context
	switch, as suggested by Nick Piggin.

Changes since v2:

o	Created rcu_blocking_is_gp() internal-to-RCU API that
	determines whether a call to synchronize_rcu() is itself
	a grace period.

o	The definition of rcu_blocking_is_gp() for rcuclassic and
	rcutree checks to see if but a single CPU is online.

o	The definition of rcu_blocking_is_gp() for rcupreempt
	checks to see both if but a single CPU is online and if
	the system is still in early boot.

	This allows rcupreempt to again work correctly if running
	on a single CPU after booting is complete.

o	Added check to rcupreempt's synchronize_sched() for there
	being but one online CPU.

Tested all three variants both SMP and !SMP, booted fine, passed a short
rcutorture test on both x86 and Power.
Located-by: NVegard Nossum <vegard.nossum@gmail.com>
Tested-by: NVegard Nossum <vegard.nossum@gmail.com>
Tested-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
      a6826048
    • B
      ide: fix refcounting in device drivers · 8fed4368
      由 Bartlomiej Zolnierkiewicz 提交于 
      During host driver module removal del_gendisk() results in a final
put on drive->gendev and freeing the drive by drive_release_dev().

Convert device drivers from using struct kref to use struct device
so device driver's object holds reference on ->gendev and prevents
drive from prematurely going away.

Also fix ->remove methods to not erroneously drop reference on a
host driver by using only put_device() instead of ide*_put().
Reported-by: NStanislaw Gruszka <stf_xl@wp.pl>
Tested-by: NStanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      8fed4368
  17. 25 2月, 2009 4 次提交
  19. 23 2月, 2009 1 次提交
  21. 22 2月, 2009 1 次提交
  23. 21 2月, 2009 3 次提交
    • M
      8250: fix boot hang with serial console when using with Serial Over Lan port · b6adea33
      由 Mauro Carvalho Chehab 提交于 
      Intel 8257x Ethernet boards have a feature called Serial Over Lan.

This feature works by emulating a serial port, and it is detected by
kernel as a normal 8250 port.  However, this emulation is not perfect, as
also noticed on changeset 7500b1f6.

Before this patch, the kernel were trying to check if the serial TX is
capable of work using IRQ's.

This were done with a code similar this:

        serial_outp(up, UART_IER, UART_IER_THRI);
        lsr = serial_in(up, UART_LSR);
        iir = serial_in(up, UART_IIR);
        serial_outp(up, UART_IER, 0);

        if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
		up->bugs |= UART_BUG_TXEN;

This works fine for other 8250 ports, but, on 8250-emulated SoL port, the
chip is a little lazy to down UART_IIR_NO_INT at UART_IIR register.

Due to that, UART_BUG_TXEN is sometimes enabled.  However, as TX IRQ keeps
working, and the TX polling is now enabled, the driver miss-interprets the
IRQ received later, hanging up the machine until a key is pressed at the
serial console.

This is the 6 version of this patch.  Previous versions were trying to
introduce a large enough delay between serial_outp and serial_in(up,
UART_IIR), but not taking forever.  However, the needed delay couldn't be
safely determined.

At the experimental tests, a delay of 1us solves most of the cases, but
still hangs sometimes.  Increasing the delay to 5us was better, but still
doesn't solve.  A very high delay of 50 ms seemed to work every time.

However, poking around with delays and pray for it to be enough doesn't
seem to be a good approach, even for a quirk.

So, instead of playing with random large arbitrary delays, let's just
disable UART_BUG_TXEN for all SoL ports.

[akpm@linux-foundation.org: fix warnings]
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      b6adea33
    • M
      spi_bitbang: add more lowlevel function documentation · 01b24fee
      由 Michael Buesch 提交于 
      This adds more documentation of the lowlevel API to avoid future bugs.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      01b24fee
    • J
      slab: introduce kzfree() · 3ef0e5ba
      由 Johannes Weiner 提交于 
      kzfree() is a wrapper for kfree() that additionally zeroes the underlying
memory before releasing it to the slab allocator.

Currently there is code which memset()s the memory region of an object
before releasing it back to the slab allocator to make sure
security-sensitive data are really zeroed out after use.

These callsites can then just use kzfree() which saves some code, makes
users greppable and allows for a stupid destructor that isn't necessarily
aware of the actual object size.
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Reviewed-by: NPekka Enberg <penberg@cs.helsinki.fi>
Cc: Matt Mackall <mpm@selenic.com>
Acked-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      3ef0e5ba
  25. 20 2月, 2009 1 次提交