* Assign drive->quirk_list in ->quirkproc implementations:
  - hpt366.c::hpt3xx_quirkproc()
  - pdc202xx_new.c::pdcnew_quirkproc()
  - pdc202xx_old.c::pdc202xx_quirkproc()

* Make ->quirkproc void.

* Move calling ->quirkproc from do_identify() to probe_hwif().

* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.

* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
  no longer needed drive->present check from is_dev_seagate_sata().

* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
  as an argument.  Then convert ide_register_hw() to accept 'quirkproc'
  argument instead of 'fixup' one.

* Remove no longer needed ->fixup method.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Dump taskfile HOB registers in ide_tf_load() (if DEBUG is defined).

* Remove no longer needed DEBUG code from __ide_do_rw_disk().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Enable/disable UDMA in atiixp_set_dma_mode().

* Remove no longer needed atiixp_dma_host_{on,off}() and save_mdma_mode[].

* Bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename cris_dma_{on,off}() to cris_dma_host_{on,off}().

* Remove no longer needed ->dma_off_quietly
  (IDE core has the needed code now).

* Make cris_dma_host_on() void.

I left fixing ide-cris after "kill dma_on/dma_off_quietly() methods"
patch because:

* Currently this driver is broken: cris_dma_on() (returns 'int')
  is assigned to hwif->dma_host_on (returns 'void') so the driver
  won't build.

* ->ide_dma_on method was missing so the driver OOPS-es on attempt
  to enable DMA.

* drive->using_dma was never set/cleared so DMA wouldn't be used anyway.

Unfortunately it seems that ide-cris stays broken even after this patch:

* V10: <asm/arch-v10/ide.h> needs fixing
  - ide_init_default_hwifs() should be removed
    (IDE core no longer uses it)
  - same for ide_init_hwif_ports() and ide_default_{irq,io_base}()
    (they shouldn't be needed for ide-cris host driver)

* V32: I'm unable to find a place which defines ETRAX_ARCH_V32

but I'm leaving fixing this to CRIS gurus. :)

Cc: Mikael Starvik <starvik@axis.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make ide_dma_off_quietly() and __ide_dma_on() always available.

* Drop "__" prefix from __ide_dma_on().

* Check for presence of ->dma_host_on instead of ->ide_dma_on.

* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
  to use ide_dma_on() and ide_dma_off_quietly() instead.

* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
  from ide_hwif_t.

* Make ide_dma_on() void.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().

Since there is no PCI device there should be no functionality
changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().

Since there is no PCI device there should be no functionality
changes caused by this patch.

Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().

Tested on Altix by Jeremy.
Acked-by: NJeremy Higdon <jeremy@sgi.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix SWDMA/MWDMA masks in cy82c693_chipset.

* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
  check whether the DMA should be enabled even if ide_max_dma_mode()
  fails.

* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
  and remove no longer needed cy82c693_ide_dma_on().  Then set
  IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
  cy82c693_chipset.

* Bump driver version.

As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Mask device DMA masks by ATA_{S,M}WDMA2 in cy82c693_ide_dma_on().

* Remove clipping of DMA modes by id->tDMA in cy82c693_dma_enable():
  - id->tDMA may not be defined on newer devices
  - id->vendor6/id->tDMA word is in LE endianness
    (cy82c693 seems to be Alpha specific though)

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Set the correct hwif->dma_base for the second channel in
  ide_get_or_set_dma_base().

* Remove DMA enable code from cs5520_set_pio_mode(), this can
  be handled by the generic ->dma_host_on method now.

* Add VDMA check to ide_config_drive_speed().

* drive->using_dma was never enabled since cs5520 host driver's
  ->ide_dma_on method overrided the generic ->ide_dma_on (so
  __ide_dma_on() was never called, drive->using_dma was never set
  and VDMA was never used since it depends on drive->using_dma).

  Fix it by using ->dma_host_on method instead of ->ide_dma_on
  (also add matching ->dma_host_off method).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

IDE core guarantees that ->set_dma_mode will be called only
for DMA modes set in SWDMA/MWDMA/UDMA masks.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Program register 0x40 in sl82c105_resetproc().

* Remove no longer needed sl82c105_selectproc() and pci_set_drvdata() calls.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Program DMA timings in sl82c105_dma_start() (->dma_start method)
  before starting DMA transfer.

* Add sl82c105_dma_end() (->ide_dma_end method) to switch back to
  PIO timings when DMA transfer is complete.

* In sl82c105_set_pio_mode() program timings regardless of ->using_dma
  setting and in sl82c105_set_dma_mode() only cache the new timings.

* Remove no longer needed sl82c105_{ide_dma_on,off_quietly}().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

->ide_dma_on method is called only after successful ide_dma_check() call
(ide_dma_check()->ide_tune_dma() checks DMA blacklist) or if drive->using_dma
has been previously enabled for a given device (->ide_dma_on is the only place
which sets drive->using_dma to '1').

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* ->dma_off_quietly is always called before ide_set_dma()
  so the call can be moved inside ide_set_dma().

* ide_dma_check() doesn't touch hardware so ->dma_off_quietly
  call for 'rc == -1' case is redundant, remove it.

* '0' and '-1' are the only values returned by ide_dma_check()
  so remove dead code for other cases.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_set_dma() calls ->ide_dma_on method itself and returns zero
only if ->ide_dma_on call succeeded.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on pata_sc1200.c.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
  what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().

* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
  (aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
  serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
  methods in host drivers that don't (IDE core code guarantees that
  ->set_dma_mode will be called only for modes which are present
  in SWDMA/MWDMA/UDMA masks).

While at it:

* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
  hpt34x/hpt366/pdc202xx_old/serverworks host driver.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out UDMA programming code from sis_set_dma_mode() to per
  chipset family helpers: sis_{ata33,ata133}_program_udma_timings().

* Add sis_program_udma_timings() helper.

* Remove unneeded casts to 'unsigned long'.

* Minor cleanups.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move PIO programming code from pdcnew_set_mode() to pdcnew_set_pio_mode().

* Rename pdcnew_set_mode() to pdcnew_set_dma_mode().

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move the common code from ide_dump_{ata,atapi}_status() to
  ide_dump_status().

* ide_dump_{ata,atapi}_status() -> ide_dump_{ata,atapi}_error().

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Export ide_get_lba_addr().

* Convert idedisk_{read_native,set}_max_address() to use ide_get_lba_addr().

* Remove incorrect comment from idedisk_read_native_max_address()
  (noticed by Sergei).

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

power4:

drivers/ide/ide-lib.c: In function `ide_dump_sector':
drivers/ide/ide-lib.c:516: warning: long long unsigned int format, u64 arg (arg 2)

We don't know what type is used to implement u64 hence it must always be cast
when printed.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out code reading taskfile registers from ide_end_drive_cmd()
  to the new ide_tf_read() helper.

* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
  particular IDE taskfile register in ide_tf_read().

* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.

* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.

* Factor out code getting sector address from ide_dump_ata_status()
  to the new ide_dump_sector() function.

* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().

* Remove no longer needed ide_read_24().

The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix registers loading order in ide_dump_ata_status()/ide_read_24().

Load registers in this order:
* IDE_SECTOR_REG
* IDE_LCYL_REG
* IDE_HCYL_REG
* IDE_SELECT_REG

It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_DMA_PIO_FALLBACK taskfile flag to indicate the need
  to skip loading taskfile registers in do_rw_taskfile().

* Export do_rw_taskfile().

* Convert __ide_do_rw_disk() to use do_rw_taskfile().

* Unexport ide_tf_load().

* Unexport {pre_task_out,task_in}_intr() and make it static.

* Remove incorrect comment about do_rw_taskfile() from <linux/ide.h>.

There should be no functionality changes caused by this patch.

v2:
* Add missing blk_fs_request() check to task_dma_ok() (for VDMA).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_tf_set_cmd() helper for selecting/setting command and data phase
  (note: DMA data phases are there for completness, they are not required ATM).

* Set IDE_TFLAG_WRITE taskfile flag for write requests in __ide_do_rw_disk().

* Convert __ide_do_rw_disk() to use the new ide_tf_set_cmd() helper.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

s/WAIT_CMD/WAIT_WORSTCASE/ to make the timeout the same as in do_rw_taskfile()
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_CUSTOM_HANDLER taskfile flag and use it for internal requests
  which require custom handlers.  Check the flag in do_rw_taskfile() and set
  handler accordingly.

* Cleanup ide_init_{specify,restore,setmult}_cmd() and rename it to
  ide_tf_set_{specify,restore,setmult}_cmd().

* Make {set_geometry,recal,set_multmode}_intr() static.

* Remove no longer needed 'handler' field from ide_task_t.

v2:
* 'handler' in do_rw_taskfile() must be set to NULL initially.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use ->data_phase to set ->handler in do_rw_taskfile() instead of
  setting ->handler in callers of ide_raw_taskfile()/do_rw_taskfile().

* Unexport task_no_data_intr() and make it static.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use task->data_phase in do_rw_taskfile() to decide what to do.

* task->prehandler is only used by TASKFILE[_MULTI]_OUT so just
  use pre_task_out_intr() directly and remove no longer needed
  'prehandler' field from ide_task_t.

* Remove no longer needed ide_pre_handler_t type.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the earlier work by Tejun Heo.

task->data_phase == TASKFILE_MULTI_{IN,OUT} vs drive->mult_count == 0
check is needed also for ide_taskfile_ioctl() requests that don't have
IDE_TFLAG_FLAGGED taskfile flag set.

Cc: Tejun Heo <htejun@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix __ide_do_rw_disk() to use ->OUTBSYNC instead of ->OUTB
(needed for pmac and scc_pata host drivers).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Save PCI regs values for both IDE ports in one buffer, in order to eliminate
a needless and ugly loop across all hwifs, searching for our PCI device.

Partially based on the previous patch by Jeff Garzik.

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_IN_DATA taskfile flag to indicate the need of reading
  IDE_DATA_REG in ide_end_drive_cmd().

  Set the new flag in ide_taskfile_ioctl() if ->in_flags.b.data is set.

* Add IDE_TFLAG_FLAGGED_SET_IN_FLAGS taskfile flag to indicate the
  need of modifying ->in_flags in ide_taskfile_ioctl().

  Set the new flag in flagged_taskfile() and move the code modifying
  ->tf_in_flags to ide_taskfile_ioctl().

  While at it remove the bogus comment: ->tf_in_flags (except .b.data)
  have no effect on selection of registers to read.

* Remove no longer needed 'tf_in_flags' field from ide_task_t.

As the result we finally have the internals of HDIO_DRIVE_TASKFILE ioctl
separated from the core IDE code.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>