The SPI driver does a couple of card cleanup steps in the wrong order on
module removal.  If IEEE PS is enabled, this results in the card being
left in IEEE PS mode and subsequent failures to reload the module.  The
problem is that the surpriseremoved flag is set before calling
lbs_remove_card, but that function needs to issue a command to exit IEEE
PS mode (the flag blocks the command path).  In addition, lbs_stop_card
should be called first because it clears out any pending commands.

Tested on a GSPI device with V9 firmware by confirming that we can
reload the module with or without IEEE PS enabled.

Also fix a warning from the wrong uint format in a printk.

V2: use z modifier, thanks Sebastian.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Libertas currently maintains a copy of the WPA unicast and group keys
when using WPA or WPA2.  This copy is checked when deciding whether or
not to return to sleep in IEEE PS mode but the actual copying back to
priv was omitted, which breaks IEEE PS mode with WPA/WPA2 when one
issues commands that require temporarily keeping the device awake.

This patch introduces the omitted copy-back of the keys so that IEEE PS
functions correctly in WPA/WPA2 mode.  Thanks to Dan Williams for
clearing up the issue.

V2: fix typo.  Also, this has been tested on GSPI and SDIO with V9 firmware.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Power save support depends on the firmware capabilities rather than the
card's hardware interface.  Use the FW_CAPINFO_PS bit in the firmware
capabilities mask throughout the driver in place of the redundant
ps_supported flag and don't make decisions about PS support in the
interface drivers (with the exception of a special case in the USB
driver).

V2: put the USB special case in the right place.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.

And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.

debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/

Fix inconsistency of directory name to mount debugfs filesystem.

* From Steven Rostedt
  - find_debugfs() and tracing_files() in this patch.
Signed-off-by: NGeunSik Lim <geunsik.lim@samsung.com>
Acked-by     : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by  : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by  : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch eplaces the shared FIRMWARE_NAME_MAX definition with a libertas
local one.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

|BUG: spinlock recursion on CPU#0, lbs_spi_thread/1030
| lock: dee9a1bc, .magic: dead4ead, .owner: lbs_spi_thread/1030, .owner_cpu: 0
|Call Trace:
|[deec3eb0] [c0007220] show_stack+0x4c/0x15c (unreliable)
|[deec3ef0] [c0187720] spin_bug+0x9c/0xb0
|[deec3f10] [c0187890] _raw_spin_lock+0x54/0x148
|[deec3f40] [c02d260c] _spin_lock_irqsave+0x2c/0x44
|[deec3f60] [e8671800] lbs_queue_event+0x7c/0x130 [libertas]
|[deec3f80] [e8725f04] lbs_spi_thread+0x538/0x58c [libertas_spi]
|[deec3fe0] [c004f270] kthread+0x4c/0x88
|[deec3ff0] [c000f33c] kernel_thread+0x4c/0x68

if_spi_e2h() is grabbing ->driver_lock just while calling
lbs_queue_event() which is grabbing the same lock.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The card firmware does not set the Command Download Ready interrupt bit
when IEEE PS mode is enabled, preventing the driver from sending
commands (such as the command to exit IEEE PS mode) since there is no
indication that the card is ready to accept commands.

This patch works around the problem by using the the TX Download Ready
bit in place of the Command Download Ready Bit while in IEEE PS mode.
TX Download Ready is set in IEEE PS mode.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the dependency on GPIO framework and lets the SPI host
driver handle the chip select. The SPI host driver is required to keep
the CS active for the entire message unless cs_change says otherwise.
This patch collects the two/three single SPI transfers into a message.
Also the delay in read path in case use_dummy_writes are not used is
moved into the SPI host driver.
Tested-by: NMike Rapoport <mike@compulab.co.il>
Tested-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is to incorporate Dan Williams' comments for commit:
"libertas: implement function init/shutdown commands for SD8688"

1. remove fn_init_required and fn_shutdown_required variables from
lbs_private structure. If required, __lbs_cmd() will be called
directly to send function init/shutdown command for SD8688 in
if_sdio_probe() or if_sdio_remove() callback.

2. add global variable "user_rmmod" to distinguish between the module
removal case and the card removal case. This flag will be checked in
if_sdio_remove() against SD8688 card to determine whether or not the
function shutdown command needs to be sent.

3. remove "card" from if_sdio_model structure as it cannot store
card pointers for multiple cards. Besides, it's no longer needed
to store the "card" pointer with changes #1 & #2 above.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Oddly enough, the firmware's JOIN/START commands don't appear to have
any facility for setting custom IEs, thus the started adhoc network
doesn't advertise its WPA capability in the beacon.  Whee!
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And fix up setting authentication suite for v9+ firmware too.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Easier to read and more conformant with kernel style.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the parameters for association/join/start commands aren't
used (like the FH and CF IEs for IBSS, and the FH IE for BSS), so
get rid of their unions to reduce indirection.  Also clean up
structure names for kernel style.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The comment (which I remove) says that the translation is done SPI routines.
IMHO this can't work because the SPI driver does not know whether the incomming
bytes are part of the registers/bytes which need to be flipped or part of
packet data which has to remain untouched.
While adding le helpers I also removed spu_write_u32() which has no users.
Tested-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The scratch pad register is used to store firmware status after
firmware is downloaded and initialized. After firmware status is
verified OK, the same register is used to store RX packet length.
Hence the firmware status code is no longer valid afterwards.

SD8688 firmware introduces a new register for firmware status
which will never be overwritten.

Also add scratch_reg variable to if_sdio_card structure and
initialize it based on the model of the card during probe.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SD8688 is a WLAN/Bluetooth combo chip and both functions are supported
in a single firmware image. FUNC_INIT and FUNC_SHUTDOWN commands are
implemented to utilize the multiple function feature.

When SD8688 card is inserted, the firmware image should be downloaded
only once through either WLAN function (Libertas driver) or Bluetooth
function (Bluetooth driver).

This patch adds function init/shutdown for SD8688 WLAN function only.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Usually, the 16-bit rx length is read from scratch pad registers
with two CMD52 transactions:
SD8385: 	IF_SDIO_SCRATCH_OLD (0x80fe/0x80ff)
SD8686/SD8688:	IF_SDIO_SCRATCH     (0x34/0x35)

Alternatively, SD8688 firmware offers an enhanced method for driver
to read an 8-bit rx length (in units) with a single CMD52:
IF_SDIO_RX_UNIT 0x43 is read one time after firmware is ready.
IF_SDIO_RX_LEN  0x42 is read every time when rx interrupt is received.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

replace direct usages of SDIO model numbers with defined macros.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The GPSI interface driver does not re-enable the Card Event Interrupt, which
causes problems after a card event (for example: link-loss) comes in.  This
can lead, for example, to the card failing to re-associate.  This patch
ensures that we re-enable the Card Event Interrupt when we handle card events.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_c2h_data’:
drivers/net/wireless/libertas/if_spi.c:733: warning: format ‘%u’ expects type ‘unsigned int’, but argument 4 has type ‘long unsigned int’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A detection function was added for identifying CF8381.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/libertas/rx.c: In function ‘lbs_process_rxed_packet’:
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 4 has type ‘__le32’
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 5 has type ‘unsigned int’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

libertas: add support for Marvell SD8688 chip

Use RxPD->pkt_ptr to locate eth803 header in the packet
received since SD8688/v10 firmware allows a gap between
RxPD and eth803 header.

Set SDIO block size to 256 for CMD53.
The maximum block size for SD8688 WLAN function is set
to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size
results upto 2K bytes data (4 blocks) being transferred
and causes buffer overflow in firmware.

Both changes above are backward compatible with earlier
firmware versions for SD8385/SD8686.

The SDIO_DEVICE_IDs for SD8688 chip are added in
include/linux/mmc/sdio_ids.h
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the libertas main thread contends with the spi driver thread
in the TX path.  To improve throughput, ensure that the driver thread
has higher scheduling priority than the libertas main thread.  Do this
by making the libertas spi driver thread a low priority real time
thread.

We measured an average throughput improvement of 13%.
Signed-off-by: NAnna Neal <anna@cozybit.com>
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CMD_MESH_CONFIG command ID and a couple of structure members in TxPD,
RxPD have been changed in firmware version 10.x.y.z and newer.
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't lead memory when receive errors
Signed-off-by: NPhilip Rakity <prakity@yahoo.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix misspelling of firmware.
Signed-off-by: NNick Andrew <nick@nick-andrew.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The libertas SDIO interface scheduled the packet worker, resulting in
unwanted latency for every data packet or command sent to the firmware.
Fix a bug on the SDIO probe error path too.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The problem: "iwconfig ethX power on" returns error

The cause: "ps_supported" flag was never set for SD8385/8686

The fix: check firmware capabilities returned by GET_HW_SPEC command.
Set "ps_supported" to 1 if FW_CAPINFO_PS bit is on. This fix applies
to SDIO interface only.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mesh and radiotap interfaces need to use the same private data as
the main wifi interface.  If the main wifi interface uses netdev_priv(),
but the other interfaces ->ml_priv, there's no way to figure out where
the private data actually is in the WEXT handlers and netdevice
callbacks.  So make everything use ->ml_priv.

Fixes botched netdev_priv() conversion introduced by "netdevice
libertas: Fix directly reference of netdev->priv", though admittedly
libertas' use of ->priv was somewhat "special".
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Tested-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

pos[4] can't be both 0x43 and 0x04, 2nd should be pos[5]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In certain cases it is required to perform board specific actions
before activating libertas G-SPI interface. These actions may include
power up of the chip, GPIOs setup, proper pin-strapping and SPI
controller config.
This patch adds ability to call board specific setup/teardown methods
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

if_cs_poll_while_fw_download() returned the number of iterations
remaining on success, which in turn got returned as the value from
if_cs_prog_real() and if_cs_prog_helper().  But since if_cs_probe()
interprets non-zero return values from firmware load functions as an
error, this sometimes caused spurious firmware load failures.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Tested-by: NRyan Mallon <ryan@bluewatersys.com>
Acked-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add initial support for libertas devices using a GSPI interface.  This has
been tested with the 8686.

GSPI is intended to be used on embedded systems. Board-specific parameters are
required (see libertas_spi.h).

Thanks to everyone who took a look at the earlier versions of the patch.
Signed-off-by: NColin McCabe <colin@cozybit.com>
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>