Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 24 9月, 2013 4 次提交
    • F
      xhci: Fix race between ep halt and URB cancellation · 526867c3
      由 Florian Wolter 提交于 
      The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699Signed-off-by: NFlorian Wolter <wolly84@web.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      526867c3
    • S
      usb: Fix xHCI host issues on remote wakeup. · 8b3d4570
      由 Sarah Sharp 提交于 
      When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.

EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:

                        /* stop resume signaling */
                        temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
                        ehci_writel(ehci, temp, status_reg);
                        clear_bit(wIndex, &ehci->resuming_ports);
                        retval = ehci_handshake(ehci, status_reg,
                                        PORT_RESUME, 0, 2000 /* 2msec */);

Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core.  When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.

After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device.  The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7.  The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.

This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0.  ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.

I attempted to replicate this bug with Ubuntu 12.04, but could not.  I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with.  I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      8b3d4570
    • M
      xhci: Ensure a command structure points to the correct trb on the command ring · ec7e43e2
      由 Mathias Nyman 提交于 
      If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.

Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)

Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.

This should also solve some weird behavior happening in command cancellation cases.

This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
    http://marc.info/?l=linux-usb&m=136269803207465&w=2

This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c "xHCI: add aborting
command ring function"
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      ec7e43e2
    • M
      xhci: Fix oops happening after address device timeout · 284d2055
      由 Mathias Nyman 提交于 
      When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.

Don't handle command completion events on stopped cmd ring if ring is
empty.

This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c "xHCI: add aborting
command ring function"
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: NGiovanni <giovanni.nervi@yahoo.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      284d2055
  3. 18 9月, 2013 2 次提交
  5. 13 9月, 2013 1 次提交
  7. 31 8月, 2013 5 次提交
  9. 29 8月, 2013 1 次提交
    • S
      xhci: Fix warning introduced by disabling runtime PM. · e7ecf069
      由 Sarah Sharp 提交于 
      The 0day build server caught a new build warning that is triggered when
CONFIG_USB_DEFAULT_PERSIST is turned on:

tree:   git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci.git for-usb-next
head:   0730d52a
commit: c8476fb8 [1/3] usb: xhci: Disable runtime PM suspend for quirky controllers
config: i386-randconfig-r6-0826 (attached as .config)

All warnings:

   drivers/usb/host/xhci.c: In function 'xhci_free_dev':
>> drivers/usb/host/xhci.c:3560:17: warning: unused variable 'dev' [-Wunused-variable]
     struct device *dev = hcd->self.controller;
                    ^
   drivers/usb/host/xhci.c: In function 'xhci_alloc_dev':
>> drivers/usb/host/xhci.c:3648:17: warning: unused variable 'dev' [-Wunused-variable]
     struct device *dev = hcd->self.controller;
                    ^

vim +/dev +3560 drivers/usb/host/xhci.c

  3554   * disabled.  Free any HC data structures associated with that device.
  3555   */
  3556  void xhci_free_dev(struct usb_hcd *hcd, struct usb_device *udev)
  3557  {
  3558          struct xhci_hcd *xhci = hcd_to_xhci(hcd);
  3559          struct xhci_virt_device *virt_dev;
> 3560          struct device *dev = hcd->self.controller;
  3561          unsigned long flags;
  3562          u32 state;
  3563          int i, ret;
  3564
  3565  #ifndef CONFIG_USB_DEFAULT_PERSIST
  3566          /*
  3567           * We called pm_runtime_get_noresume when the device was attached.
  3568           * Decrement the counter here to allow controller to runtime suspend
  3569           * if no devices remain.
  3570           */
  3571          if (xhci->quirks & XHCI_RESET_ON_RESUME)
  3572                  pm_runtime_put_noidle(dev);
  3573  #endif
  3574
...
  3641  /*
  3642   * Returns 0 if the xHC ran out of device slots, the Enable Slot command
  3643   * timed out, or allocating memory failed.  Returns 1 on success.
  3644   */
  3645  int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev)
  3646  {
  3647          struct xhci_hcd *xhci = hcd_to_xhci(hcd);
> 3648          struct device *dev = hcd->self.controller;
  3649          unsigned long flags;
  3650          int timeleft;
  3651          int ret;

Fix this.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Shawn Nematbakhsh <shawnn@chromium.org>
      e7ecf069
  11. 28 8月, 2013 2 次提交
  13. 27 8月, 2013 4 次提交
  15. 24 8月, 2013 3 次提交
  17. 16 8月, 2013 1 次提交
    • S
      xhci-plat: Don't enable legacy PCI interrupts. · 52fb6125
      由 Sarah Sharp 提交于 
      The xHCI platform driver calls into usb_add_hcd to register the irq for
its platform device.  It does not want the xHCI generic driver to
register an interrupt for it at all.  The original code did that by
setting the XHCI_BROKEN_MSI quirk, which tells the xHCI driver to not
enable MSI or MSI-X for a PCI host.

Unfortunately, if CONFIG_PCI is enabled, and CONFIG_USB_DW3 is enabled,
the xHCI generic driver will attempt to register a legacy PCI interrupt
for the xHCI platform device in xhci_try_enable_msi().  This will result
in a bogus irq being registered, since the underlying device is a
platform_device, not a pci_device, and thus the pci_device->irq pointer
will be bogus.

Add a new quirk, XHCI_PLAT, so that the xHCI generic driver can
distinguish between a PCI device that can't handle MSI or MSI-X, and a
platform device that should not have its interrupts touched at all.
This quirk may be useful in the future, in case other corner cases like
this arise.

This patch should be backported to kernels as old as 3.9, that
contain the commit 00eed9c8 "USB: xhci:
correctly enable interrupts".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NYu Y Wang <yu.y.wang@intel.com>
Tested-by: NYu Y Wang <yu.y.wang@intel.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
      52fb6125
  19. 15 8月, 2013 1 次提交
  21. 14 8月, 2013 14 次提交
    • X
      xhci: fix dma mask setup in xhci.c · c10cf118
      由 Xenia Ragiadakou 提交于 
      The function dma_set_mask() tests internally whether the dma_mask pointer
for the device is initialized and fails if the dma_mask pointer is NULL.
On pci platforms, the device dma_mask pointer is initialized, when pci
devices are enumerated, to point to the pci_dev->dma_mask which is 0xffffffff.
However, for non-pci platforms, the dma_mask pointer may not be initialized
and in that case dma_set_mask() will fail.

This patch initializes the dma_mask and the coherent_dma_mask to 32bits
in xhci_plat_probe(), before the call to usb_create_hcd() that sets the
"uses_dma" flag for the usb bus and the call to usb_add_hcd() that creates
coherent dma pools for the usb hcd.

Moreover, a call to dma_set_mask() does not set the device coherent_dma_mask.
Since the xhci-hcd driver calls dma_alloc_coherent() and dma_pool_alloc()
to allocate consistent DMA memory blocks, the coherent DMA address mask
has to be set explicitly.

This patch sets the coherent_dma_mask to 64bits in xhci_gen_setup() when
the xHC is capable for 64-bit DMA addressing.

If dma_set_mask() succeeds, for a given bitmask, it is guaranteed that
the given bitmask is also supported for consistent DMA mappings.

Other changes introduced in this patch are:

- The return value of dma_set_mask() is checked to ensure that the required
  dma bitmask conforms with the host system's addressing capabilities.

- The dma_mask setup code for the non-primary hcd was removed since both
  primary and non-primary hcd refer to the same generic device whose
  dma_mask and coherent_dma_mask are already set during the setup of
  the primary hcd.

- The code for reading the HCCPARAMS register to find out the addressing
  capabilities of xHC was removed since its value is already cached in
  xhci->hccparams.

- hcd->self.controller was replaced with the dev variable since it is
  already available.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      c10cf118
    • X
      xhci: trace debug statements related to ring expansion · 68ffb011
      由 Xenia Ragiadakou 提交于 
      This patch defines a new trace event, which is called xhci_dbg_ring_expansion
and belongs to the event class xhci_log_msg, and adds tracepoints that trace
the debug messages associated with the expansion of endpoint ring when there
is not enough space allocated to hold all pending TRBs.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      68ffb011
    • X
      xhci: trace debug messages related to driver initialization and unload · d195fcff
      由 Xenia Ragiadakou 提交于 
      This patch defines a new trace event, which is called xhci_dbg_init
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug statements in the functions used to start and stop the
xhci-hcd driver.

Also, it removes an unnecessary cast of variable val to unsigned int
in xhci_mem_init(), since val is already declared as unsigned int.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      d195fcff
    • X
      xhci: trace debug statements for urb cancellation · aa50b290
      由 Xenia Ragiadakou 提交于 
      This patch defines a new trace event, which is called xhci_dbg_cancel_urb
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug messages related to the removal of a cancelled URB from
the endpoint's transfer ring.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      aa50b290
    • X
      xhci: add xhci_cmd_completion trace event · 63a23b9a
      由 Xenia Ragiadakou 提交于 
      This patch creates a new event class, called xhci_log_event,
and defines the xhci_cmd_completion trace event used for
tracing the commands issued to xHC that generate a completion
event in the event ring.

This info can be used, later, to print, in a human readable
way, the completion status and flags as well as the command's
type and fields using the trace-cmd tool and the appropriate
plugin.

Also, a tracepoint is added in handle_cmd_completion().
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      63a23b9a
    • X
      xhci: add xhci_address_ctx trace event · 1d27fabe
      由 Xenia Ragiadakou 提交于 
      This patch defines a new event class, called xhci_log_ctx,
that records in the ring buffer the context data, the
context type (input or output), the context dma and virtual
addresses, the context endpoint entries, the slot ID and
whether the xHC uses 64 byte context data structures.

This information can be used, later, to parse and display
the context data fields with the appropriate plugin using
the trace-cmd tool.

Also, this patch defines a trace event, called xhci_address_ctx,
to trace the contexts related to the Address Device command and
adds the associated tracepoints in xhci_address_device().
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      1d27fabe
    • X
      xhci: add trace for debug messages related to endpoint reset · a0254324
      由 Xenia Ragiadakou 提交于 
      This patch defines a new trace event, which is called xhci_dbg_reset_ep
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with resetting an endpoint after
the reception of a STALL packet.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      a0254324
    • X
      xhci: add trace for debug messages related to quirks · 4bdfe4c3
      由 Xenia Ragiadakou 提交于 
      This patch defines a new trace event, which is called xhci_dbg_quirks
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with xHCs' quirks.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      4bdfe4c3
    • X
      xhci: add trace for debug messages related to changing contexts · 3a7fa5be
      由 Xenia Ragiadakou 提交于 
      This patch defines a new trace event, which is called xhci_dbg_context_change
and belongs in the event class xhci_log_msg, and adds tracepoints for tracing
the debug messages related to context updates performed with Configure Endpoint
and Evaluate Context commands.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      3a7fa5be
    • X
      xhci: add traces for debug messages in xhci_address_device() · 84a99f6f
      由 Xenia Ragiadakou 提交于 
      This patch declares an event class for trace events that
trace messages with variadic arguments, called xhci_log_msg,
and defines a trace event for tracing the debug messages in
xhci_address_device() function, called xhci_dbg_address.

In order to implement this type of trace events, a wrapper function,
called xhci_dbg_trace(), was created that records the format string
and variadic arguments into a va_format structure which is passed as
argument to the tracepoints of the class xhci_log_msg.

All the xhci_dbg() calls in xhci_address_device() are replaced
with calls to xhci_dbg_trace(). The functionality of xhci_dbg()
log messages was not removed though, but it is placed inside
xhci_dbg_trace().

This trace event aims to give the ability to the user or the
developper to isolate and trace the debug messages generated
when an Address Device Command is issued to xHC.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      84a99f6f
    • X
      xhci: remove CONFIG_USB_XHCI_HCD_DEBUGGING and unused code · b2497509
      由 Xenia Ragiadakou 提交于 
      CONFIG_USB_XHCI_HCD_DEBUGGING option is used to enable
verbose debugging output for the xHCI host controller
driver.

In the current version of the xhci-hcd driver, this
option must be turned on, in order for the debugging
log messages to be displayed, and users may need to
recompile the linux kernel to obtain debugging
information that will help them track down problems.

This patch removes the above debug option to enable
debugging log messages at all times.
The aim of this is to rely on the debugfs and the
dynamic debugging feature for fine-grained management
of debugging messages and to not force users to set
the debug config option and compile the linux kernel
in order to have access in that information.

This patch, also, removes the XHCI_DEBUG symbol and the
functions dma_to_stream_ring(), xhci_test_radix_tree()
and xhci_event_ring_work() that are not useful anymore.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      b2497509
    • X
      xhci: replace printk(KERN_DEBUG ...) · 5c1127d3
      由 Xenia Ragiadakou 提交于 
      This patch replaces the calls to printk(KERN_DEBUG ...)
with either calls to xhci_dbg() or calls to pr_debug(),
depending on whether the xhci_hcd structure is available
at callsite, so that the correspoding debugging messages
are not enabled by default when CONFIG_DYNAMIC_DEBUG option
is set but rather can be enabled dynamically taking advantage
of the dynamic debugging feature.

Also, it adds a newline at the end of debugging messages in
case there is not, so that messages don't appear broken
when printed.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      5c1127d3
    • X
      xhci: replace xhci_info() with xhci_dbg() · 38a532a6
      由 Xenia Ragiadakou 提交于 
      This patch replaces the calls to xhci_info() with calls to
xhci_dbg() and removes the unused xhci_info() definition
from xhci-hcd.

By replacing the xhci_info() with xhci_dbg(), the calls to
dev_info() are replaced with calls to dev_dbg() so that
their output can be dynamically controlled via the dynamic
debugging mechanism.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      38a532a6
    • A
      usb: Add Device Tree support to XHCI Platform driver · 1fe6c452
      由 Al Cooper 提交于 
      Add Device Tree match table to xhci-plat.c. Add DT bindings document.
Signed-off-by: NAl Cooper <alcooperx@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      1fe6c452
  23. 13 8月, 2013 2 次提交