be2net driver is currently not showing correct phy details in certain cases.
This patch fixes it.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Patch adds support to enable PCI SRIOV in the driver and changes to handle initialization of PCI virtual functions.
- Function handler to change mac addresses for VF from its corresponding PF.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an MCC cmd is issued (via a netdev/ethtool op)
while the device is not open, the MCC CQ gets processed but the EQ
is not processed (as isr is not registered.) This can cause the EQ
to become full. So, while the device is not open, CQ must not be re-armed
to prevent EQ entries.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now flashing both BE2 and BE3 devices is supported.

From: Naresh G <nareshg@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix in be2net for newer generation of BladeEngine ASIC.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch implements a firmware command to fetch the eeprom data.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIC controller has to be set to an appropriate mode before doing a loopback
test. Test will fail otherwise.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch adds support for ethtool selftest.

From: Suresh R <sureshr@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for WOL using Magic Packet after suspend is done.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These cmds are issued to the fw in probe/resume and remove/suspend
paths to help fw execute some initialization and cleanup code.

This change needed the be_hw_up() code to be refactored as be_get_config().
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To send upto 64 addresses in the multicast-set cmd, the non-embeeded cmd format
that provides for a bigger buffer is used instead of an embedded format.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Please apply patch to update redboot section while firmware update. Code
checks if section needs to be updated before actually doing it.
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update ethtool get_settings function to:
- get current link speed settings from controller
- get port transceiver type from controller
- fill appropriate values for supported, phy_address
Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vtp bit in RX completion descriptor could be wrongly set in
some skews of BladEngine.  Ignore this  bit if vtm is not set.
Resending because the previous patch was against net-next tree.
This patch is against the net-2.6 tree.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All cmds issued to BE after the creation of mccq must now use the mcc-q
(and not mbox) to avoid a hw issue that results in mbox poll timeout.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to support flashing of the be2 network adapter using the
request_firmware() & ethtool infrastructure. The trigger to flash the device
will come from ethtool utility. The driver will invoke request_firmware()
to start the flash process. The file containing the flash image is expected
to be available in /lib/firmware/
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a bug fix to avoid system going into a bad state when
driver is loaded in context of kdump kernel. The patch fixes the issue
by performing a soft reset of pci function at probe time.
Signed-off-by: Nsarveshwarb <sarveshwarb@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be_mbox_db_ring() has been changed to be_mbox_notify() (to be consistent with
be_mcc_notify()) and struct be_mcc_cq_entry changed to be_mcc_compl
to be consistent with rx/tx_compl.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently only the be_ctrl_info struct ptr (instead of adapter) is
 passed to all the routines in be_cmds.c. Instead pass be_adapter
ptr to allow access to all its fields. Merge the contents of struct be_ctrl_info
into be_adapter. The resulting code is simpler.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rcv and process ansync link status notifications from BE instead of polling
 for link status in the be_worker thread.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup multicast_set method to avoid an extra copy of mc_list
 and unwanted promiscuos sets to BE.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currenlty all cmds use the blocking MCC mbox to post cmds. An mbox cmd is protected
via a spin_lock(cmd_lock) and not spin_lock_bh() as it is undesirable
to disable BHs while a blocking mbox cmd is in progress (and take long to finish.)
This can lockup a cmd in progress in process context. Instead cmds that may be
called in BH context must use the MCC queue to post cmds. The cmd completions
are rcvd in a separate completion queue and the events are placed in the tx-event
queue.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>