The skb_gro_* code fails to handle the case where a header starts
in the linear area but ends in the frags area.  Since the goal
of skb_gro_* is to optimise the case of completely non-linear
packets, we can simply bail out if we have anything in the linear
area.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

>From now on FW will be downloaded from the binary file using request_firmware.

There will be different files for every supported chip. Currently 57710 (e1) and
57711 (e1h).

File names have the following format: bnx2x-<chip version>-<FW version>.fw.
ihex versions of current FW files are submitted in the next patch.

Each binary file has a header in the following format:


struct bnx2x_fw_file_section {
	__be32 len;
	__be32 offset;
}

struct bnx2x_fw_file_hdr {
	struct bnx2x_fw_file_section init_ops;
	struct bnx2x_fw_file_section init_ops_offsets;
	struct bnx2x_fw_file_section init_data;
	struct bnx2x_fw_file_section tsem_int_table_data;
	struct bnx2x_fw_file_section tsem_pram_data;
	struct bnx2x_fw_file_section usem_int_table_data;
	struct bnx2x_fw_file_section usem_pram_data;
	struct bnx2x_fw_file_section csem_int_table_data;
	struct bnx2x_fw_file_section csem_pram_data;
	struct bnx2x_fw_file_section xsem_int_table_data;
	struct bnx2x_fw_file_section xsem_pram_data;
	struct bnx2x_fw_file_section fw_version;
}

Each bnx2x_fw_file_section contains the length and the offset of the appropriate
section in the binary file. Values are stored in the big endian format.

Data types of arrays:

init_data            __be32
init_ops_offsets     __be16
XXsem_pram_data         u8
XXsem_int_table_data    u8
init_ops             struct raw_op {
                          u8   op;
			__be24 offset;
                        __be32 data;
		     }
fw_version              u8

>From now boundaries of a specific initialization stage are stored in
init_ops_offsets array instead of being defined by separate macroes. The index 
in init_ops_offsets is calculated by BLOCK_OPS_IDX macro:

#define BLOCK_OPS_IDX(block, stage, end) \
       (2*(((block)*STAGE_IDX_MAX) + (stage)) + (end))

Security:

In addition to sanity check of array boundaries bnx2x will check a FW version.
Additional checks might be added in the future.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When creating a certain types of VPN, NetworkManager will first attempt
to find an available tun device by iterating through 'vpn%d' until it
finds one that isn't already busy. Then it'll set that to be persistent
and owned by the otherwise unprivileged user that the VPN dæmon itself
runs as.

There's a race condition here -- during the period where the vpn%d
device is created and we're waiting for the VPN dæmon to actually
connect and use it, if we try to create _another_ device we could end up
re-using the same one -- because trying to open it again doesn't get
-EBUSY as it would while it's _actually_ busy.

So solve this, we add an IFF_TUN_EXCL flag which causes tun_set_iff() to
fail if it would be opening an existing persistent tundevice -- so that
we can make sure we're getting an entirely _new_ device.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Values of dB between -0.99 and -0.01 will be output with the wrong
sign. This converts the negative value to positive and outputs it
with a "-" prefix.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac_to_intf() can return -1 when no device or function is found, but when
mac->dma_if is unsigned. The error wasn't noticed.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I initially implemented this protocol, I disregarded the use of netlink
attribute headers, thinking for my purposes they weren't needed.  I've come to
find out that, as I'm starting to work with sending down messages with
associated data (like config messages), the kernel code spits out warnings about
trailing data in a netlink skb that doesn't have an associated header on it.  As
such, I'm going to start including attribute headers in my netlink transaction,
and so for completeness, I should likely include them on messages bound from the
kernel to user space.  This patch adds that header to the kernel, and bumps the
protocol version accordingly
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82598 and 82599 do not support SFP 1G modules.  Instead of allowing the
driver to load, but never get link, rejecting the module and displaying
a useful message is more preferrable.  The framework for displaying the
failure message already exists, now we just need to detect and reject the
SFP modules.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The igb driver was switching between adapter->itr containing the EITR value
and the number of interrupts per second.  This resulted in high latencies
being seen after brining the interface down and then back up.  To resolve
the issue the itr value will now only contain the value that should be
programmed into EITR.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Acked-by: NRam Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If vpath is NULL then hldev is NULL also.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Acked-by: NRam Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pointed out by Sean E. Millichamp.

Quote from Documentation/networking/bonding.txt:
"Note that when a bonding interface has no active links, the
driver will immediately reuse the first link that goes up, even if the
updelay parameter has been specified (the updelay is ignored in this
case).  If there are slave interfaces waiting for the updelay timeout
to expire, the interface that first went into that state will be
immediately reused.  This reduces down time of the network if the
value of updelay has been overestimated, and since this occurs only in
cases with no connectivity, there is no additional penalty for
ignoring the updelay."

This patch actually changes the behaviour in this way.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

 drivers/net/bonding/bond_main.c |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch only changes the order of interfaces to use for checking slave link
status in bond_check_dev_link() to priorize ethtool interface. Should safe some
troubles as ethtool seems to be more supported.

Jirka
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

 drivers/net/bonding/bond_main.c |   26 ++++++++++++--------------
 1 files changed, 12 insertions(+), 14 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modules are not supposed to use any of the *_initcall*() hooks as
the entry point.  fsl_pq_mdio.c was using subsys_initcall_sync()
instead of module_init() to guarantee that the MDIO bus was initialized
before the Ethernet driver goes looking for the phy.  However, the recent
OF helpers rework happens to also make sure PHY connection is deferred to
.open time, so using an initcall is no longer necessary.

This patch replaces the initcall with a more traditional an accepted
module_init() call.

Tested on Freescale MPC8349emitxgp eval board.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet
device.  The ll_temac ipcore is typically used on Xilinx Virtex and
Spartan designs attached to either a PowerPC 4xx or Microblaze
processor.

At the present moment, this driver only works with Virtex5 PowerPC
designs because it assumes DCR is used to access the DMA registers.
However, the low level access to DMA registers is abstracted and
it should be easy to adapt for the other implementations.

I'm posting this driver now as an RFC.  There are still some things that
need to be tightened up, but it does appear to be stable.

Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr.

Tested on Xilinx ML507 eval board with Base System Builder generated
FPGA design.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simplifies the driver by making use of more common code.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch modifies the bitbanged MDIO driver in the ep8248e platform
code to use the common of_mdio infrastructure.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simplifies the driver by making use of more common code.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simplifies the driver by making use of more common code.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NOlof Johansson <olof@lixom.net>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simplifies the driver by making use of more common code.

Tested on Freescale MPC8349emitxgp eval board
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simplifies the driver by making use of more common code.

Tested on Freescale MPC8349emitxgp eval board
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch reworks the MPC5200 Fast Ethernet Controller (FEC) driver to
use the of_mdio infrastructure for registering PHY devices from data out
openfirmware device tree, and eliminates the assumption that the PHY
for the FEC is always attached to the FEC's own MDIO bus.  With this
patch, the FEC can use a PHY attached to any MDIO bus if it is described
in the device tree.

Tested on Freescale Lite5200b eval board
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for parsing the device tree for PHY devices on an MDIO bus.
Currently many of the PowerPC ethernet drivers are open coding a solution
for reading data out of the device tree to find the correct PHY device.
This patch implements a set of common routines to:

a) let MDIO bus drivers register phy_devices described in the tree, and
b) let MAC drivers find the correct phy_device via the tree.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add phy_connect_direct() and phy_attach_direct() functions so that
drivers can use a pointer to the phy_device instead of trying to determine
the phy's bus_id string.

This patch is useful for OF device tree descriptions of phy devices where
the driver doesn't need or know what the bus_id value in order to get a
phy_device pointer.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes changes in preparation for supporting open firmware
device tree descriptions of MDIO busses.  Changes include:
- Cleanup handling of phy_map[] entries; they are already NULLed when
  registering and so don't need to be re-cleared, and it is good practice
  to clear them out when unregistering.
- Split phy_device registration out into a new function so that the
  OF helpers can do two stage registration (separate allocation and
  registration steps).
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

of_parse_phandle() is a helper function to read and parse a phandle
property and return a pointer to the resulting device_node.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IP MIB (RFC 4293) defines stats for InOctets, OutOctets, InMcastOctets and
OutMcastOctets:
http://tools.ietf.org/html/rfc4293
But it seems we don't track those in any way that easy to separate from other
protocols.  This patch adds those missing counters to the stats file. Tested
successfully by me

With help from Eric Dumazet.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove redundant set of skb->dev (now handled for ethernet
drivers by eth_type_trans()).
Signed-off-by: NJohn Dykstra <john.dykstra1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes an unused parameter (tb_stamp) from fib_table
structure in include/net/ip_fib.h.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	net/mac80211/pm.c

net/mac80211/tx.c: In function ‘ieee80211_tx_h_select_key’:
net/mac80211/tx.c:448: warning: ‘key’ may be used uninitialized in this function

drivers/net/wireless/ath/ath9k/rc.c: In function ‘ath_rc_rate_getidx’:
drivers/net/wireless/ath/ath9k/rc.c:815: warning: ‘nextindex’ may be used uninitialized in this function

drivers/net/wireless/hostap/hostap_plx.c: In function ‘prism2_plx_probe’:
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_index’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_offset’ may be used uninitialized in this function
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_c2h_data’:
drivers/net/wireless/libertas/if_spi.c:733: warning: format ‘%u’ expects type ‘unsigned int’, but argument 4 has type ‘long unsigned int’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix this build error caused by 362b76ed
"8390p: Get rid of init_module/cleanup_module"

drivers/net/8390p.c:94:19: error: invalid suffix "p_init_module" on integer constant
drivers/net/8390p.c:94: error: expected identifier or '(' before numeric constant
drivers/net/8390p.c:99:20: error: invalid suffix "p_cleanup_module" on integer constant
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Ursula Braun <ubraun@linux.vnet.ibm.com>

net/iucv/af_iucv.c in net-next-2.6 is almost correct. 4 lines should
still be deleted. These are the remaining changes:
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	net/iucv/af_iucv.c

The SO_MSGLIMIT socket option modifies the message limit for new
IUCV communication paths.

The message limit specifies the maximum number of outstanding messages
that are allowed for connections. This setting can be lowered by z/VM
when an IUCV connection is established.

Expects an integer value in the range of 1 to 65535.
The default value is 65535.

The message limit must be set before calling connect() or listen()
for sockets.

If sockets are already connected or in state listen, changing the message
limit is not supported.
For reading the message limit value, unconnected sockets return the limit
that has been set or the default limit. For connected sockets, the actual
message limit is returned. The actual message limit is assigned by z/VM
for each connection and it depends on IUCV MSGLIMIT authorizations
specified for the z/VM guest virtual machine.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the skb cannot be copied to user iovec, always return -EFAULT.
The skb is enqueued again, except MSG_PEEK flag is set, to allow user space
applications to correct its iovec pointer.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides the socket type SOCK_SEQPACKET in addition to
SOCK_STREAM.

AF_IUCV sockets of type SOCK_SEQPACKET supports an 1:1 mapping of
socket read or write operations to complete IUCV messages.
Socket data or IUCV message data is not fragmented as this is the
case for SOCK_STREAM sockets.

The intention is to help application developers who write
applications or device drivers using native IUCV interfaces
(Linux kernel or z/VM IUCV interfaces).
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>