arch/powerpc/platforms/pseries/hotplug-memory.c uses
remove_section_mapping() but doesn't include sparsemem.h which defines
it.  This can cause compilation fails for some configs.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The new legacy_mem file in sysfs is causing problems with X on machines
that don't support legacy memory access. The way I initially implemented
it, we would fail with -ENXIO when trying to mmap it, thus exposing to
X that we do support the API but there is no legacy memory.

Unfortunately, X poor error handling is causing it to fail to start when
it gets this error.

This implements a workaround hack that instead maps anonymous memory
instead (using shmem if VM_SHARED is set, just like /dev/zero does).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

arch/powerpc/oprofile/cell/spu_profiler.c is missing a asm/time.h
include which is required for ppc_proc_freq.  This can cause compile
failures for some config combinations.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Impact: fix dynamic ftrace with large modules in PPC64

The math to calculate the offset into the TOC that is taken from reading
the trampoline is incorrect. The bottom half of the offset is a signed
extended short. The current code was using an OR to create the offset
when it should have been using an addition.
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently emulate_step() emulates mr. instructions without updating cr0
and this can be disastrous. Don't emulate mr.

This bug has been around for a while, but I am not sure if its a worthy
-stable candidate. I'll leave it to Ben do decide.
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Fixed v_mapped_by_tlbcam() and p_mapped_by_tlbcam() to use phys_addr_t
instead of unsigned long.  In 36-bit physical mode we really need these
functions to deal with phys_addr_t when trying to match a physical
address or when returning one.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

in_interrupt() requires #inclusion of linux/hardirq.h not asm/hardirq.h now.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Architectures other than mips and x86 are not using ticket spinlocks.
Therefore, the contention on the lock is meaningless, since there is
nobody known to be waiting on it (arguably /fairly/ unfair locks).

Dummy it out to return 0 on other architectures.
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is based upon a report from Chris Torek and his initial patch.
From Chris's report:

--------------------
This came up in testing kgdb, using the built-in tests -- turn
on CONFIG_KGDB_TESTS, then

    echo V1 > /sys/module/kgdbts/parameters/kgdbts

-- but it would affect using kgdb if you were debugging and looking
at bad pointers.
--------------------

When we get a copy_{from,to}_user() request and the %asi is set to
something other than ASI_AIUS (which is userspace) then we branch off
to a routine called memcpy_user_stub().  It just does a straight
memcpy since we are copying from kernel to kernel in this case.

The logic was that since source and destination are both kernel
pointers we don't need to have exception checks.

But for what probe_kernel_{read,write}() is trying to do, we have to
have the checks, otherwise things like kgdb bad kernel pointer
accesses don't do the right thing.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is an implementation of a suggestion made by Chris Torek:
--------------------
Something else I noticed in passing: the EX and EX_LD/EX_ST macros
scattered throughout the various .S files make a fair bit of .fixup
code, all of which does the same thing.  At the cost of one symbol
in copy_in_user.S, you could just have one common two-instruction
retl-and-mov-1 fixup that they all share.
--------------------

The following is with a defconfig build:

   text	   data	    bss	    dec	    hex	filename
3972767	 344024	 584449	4901240	 4ac978	vmlinux.orig
39688877	 344024	 584449	4897360	 4aba50	vmlinux
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of my past fixes to this code introduced a different new bug.
When using 32-bit "int $0x80" entry for a bogus syscall number,
the return value is not correctly set to -ENOSYS.  This only happens
when neither syscall-audit nor syscall tracing is enabled (i.e., never
seen if auditd ever started).  Test program:

	/* gcc -o int80-badsys -m32 -g int80-badsys.c
	   Run on x86-64 kernel.
	   Note to reproduce the bug you need auditd never to have started.  */

	#include <errno.h>
	#include <stdio.h>

	int
	main (void)
	{
	  long res;
	  asm ("int $0x80" : "=a" (res) : "0" (99999));
	  printf ("bad syscall returns %ld\n", res);
	  return res != -ENOSYS;
	}

The fix makes the int $0x80 path match the sysenter and syscall paths.
Reported-by: NDmitry V. Levin <ldv@altlinux.org>
Signed-off-by: NRoland McGrath <roland@redhat.com>

Simply add appropriate sdhci nodes.

Note that U-Boot should configure pin multiplexing for eSDHC prior
to Linux could use it. U-Boot should also fill-in the clock-frequency
property (eSDHC clock depends on board-specific SCCR[ESDHCCM] bits).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

- sdhc node renamed to sdhci ("sdhc" name is confusing since SDHC is
  used to name Secure Digital High Capacity cards, while SDHCI is an
  interface).

- Get rid of "fsl,esdhc" compatible entry, it's replaced by the
  "fsl,<chip>-esdhc" scheme;

- Get rid of `model' property.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Taking sizeof the result of sizeof is quite strange and does not seem to be
what is wanted here.

This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression E;
@@

- sizeof (
  sizeof (E)
- )

@@
type T;
@@

- sizeof (
  sizeof (T)
- )
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is a simple change to correct problems when using set_irq_type
on platforms using CPM2.  This code corrects the problem on most platform
but may have issues on 8272 derived platforms for some interrupts.

On 8272 PC2 & 3 are missing and PC 23 & 29 are added, which this patch
does not address.
Signed-off-by: NPaul Bilke <paul@conspiracy.net>
Reviewed-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).

This patch fixes following failure during bootup:

mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

commit b31a1d8b ("gianfar: Convert
gianfar to an of_platform_driver") introduced a child node for
the ethernet@25000 controller, but no address and size cells
specifiers were added, and that makes dtc unhappy:

DTC: dts->dtb  on file "arch/powerpc/boot/dts/mpc8313erdb.dts"
Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

I noticed this doing some randconfig testing (.config below).  I have
CONFIG_PM but no CONFIG_SUSPEND.  Bug is against mainline.

arch/powerpc/sysdev/built-in.o: In function `ipic_suspend':
ipic.c:(.text+0x6b34): undefined reference to `fsl_deep_sleep'
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2

Looks like #ifdef CONFIG_PM in arch/powerpc/sysdev/ipic.c should be
CONFIG_SUSPEND.  d49747bd introduced
this.

Fix build when we have CONFIG_PM but no CONFIG_SUSPEND.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

They can't be used for profiling and NMI watchdog currently
since they lack the counter overflow interrupt.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent kprobes from catching spurious faults which will cause infinite
recursive page-fault and memory corruption by stack overflow.
Signed-off-by: NMasami Hiramatsu <mhiramat@redhat.com>
Cc: <stable@kernel.org>		[2.6.28.x]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Do usual do {} while (0) dance, otherwise

fs/gfs2/util.c:99: error: expected expression before 'else'
drivers/scsi/lpfc/lpfc_sli.c:363: error: expected expression before 'else'
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

At this time, the PowerNow! driver for K8 uses an experimentally
derived formula to calculate transition latency.  The value it
provides is orders of magnitude too large on modern systems.
This patch replaces the formula with ACPI _PSS latency values
for more accuracy and better performance.

I've tested it on two 2nd generation Opteron systems, a 3rd
generation Operton system, and a Turion X2 without seeing any
stability problems.
Signed-off-by: NMark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NDave Jones <davej@redhat.com>

This patch makes the ROM reading code return an error to user space if
the size of the ROM read is equal to 0.

The patch also emits a warnings if the contents of the ROM are invalid,
and documents the effects of the "enable" file on ROM reading.
Signed-off-by: NTimothy S. Nelson <wayland@wayland.id.au>
Acked-by: NAlex Villacis-Lasso <a_villacis@palosanto.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The removed version with the loop registers saved on the stack was
originally intended to workaround the missing toolchain support for
LoopReg Clobbers.

Since our toolchain now supports these there is no point in keeping this
workaround. And since we don't touch LoopRegs anymore we're no longer
subject for ANOMALY_05000312.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Avoid possible overflow during 32*32->32 multiplies.
Reported-by: NMarco Reppenhagen <marco.reppenhagen@auerswald.de>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

use a do...while loop rather than a for loop to get slightly better
optimization and to avoid gcc "may be used uninitialized" warnings ...
we know that the [id]cplb_nr_bounds variables will never be 0, so this
is OK
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Enable null pointer checking for ICPLBs. The code was there but for
some reason I had commented it out at some stage during development.

Should restrict this to 1K since atomic ops start there.
Signed-off-by: NBernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Blackfin arch: add platform device bfin_mii-bus and KSZ8893M switch driver platform resources to board files
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

 - unable to single step over emuexcpt instruction
 - gdbproxy goes into infinite loop when doing gdb does "next" over
   "emuexcpt"

Don't decrement PC after software breakpoint.
Signed-off-by: NJie Zhang <jie.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NBryan Wu <cooloney@kernel.org>

bss_l2 section is garbage when the data in this section is used by
_bfin_relocate_l1_mem, so move the zero out function ahead.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

base SIC_IWR# programming on whether the MMR exists
rather than having to maintain another list of processors
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>