A couple of scsi drivers define a BIT() macro, duplicating the one in
bitops.h.

Cc: Jing Huang <huangj@brocade.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update bfa driver API and data structure to support BOFM (IBM BladeCenter
Open Fabric Manager).
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When the FCoE Linkup event is sent to the host, the link_state
(struct bfa_pport_link_s) structure is copied to the RME buf to be sent to
the host. But the size of this structure(164 bytes) is larger than the
reserved RME buffer size(128 byes). The following changes reduce the size
of the structure to be less than RME buffer size(128 bytes):
- Remove the trunk and loop info from link_state structure, because both trunk
  and loop are not supported.
- Combine qos_vc_attr and fcf into an union.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add new bfa functionality to support dynamic queue selection (IO redirection).
IO redirection can only be enabled when QoS is disabled.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

BFA UF module did not hold lock when seding uf post buffer message to firmware
causing CPE-Q corruption. Fix is to check present of FCS and if FCS present
hold lock while posting UF buffers.

Handle PRLO with sending acc to it and relogin with rport. Discard fcxp
before any state change.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Clear PSS memory reset that is set as part of power-on-reset (pci reset).
Complete PMM memory reset before BISTR start. Clear EDRAM BISTR start bit
after fixed delay. BISTR DONE bit status is not getting set. Use a fixed
1ms delay for BISTR now. Expose PMM IT memory definitions to host.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Update related data structures to support firmeare configuration.
Add AEN events related to firmware configuation.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add a max retry limit for PRLI retries. Max retry limit (5) is same as used
in rport PLOGI. Once the retries are exhausted, invoke rport offline so that
existing logic of rport re-discovery can kick-in. Also fixed a bug in rport.c
where one less retry was happening.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Use standards defined 2 * RA_TOV as a timeout for ELS Request retries.
And standards defined 3 * RA_TOV as a timeout for FC-CT Request retries.
Also, added a check to send RPSC2 to a Brocade Fabric only.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Added time stamp for fcport stats reset
- Added new fileds to the statistics data structures.
- Typo removal and minor cleanup.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch fixes the APIs to obtain ioc attributes
- fix API to obtain wwpn, wwnn, and mac.
- add API to get mfg wwpn, wwnn, and mac.
- fix API to obtain wwn of boot target.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch enables creating PBC vport.
During fcs init, fcs will read PBC vport using bfa iocfc API and invoke fcb
callback to add the pbc vport entries into a list. The pbc vport list will be
traversed in the subsequent pci probe process and vport will be created using
fc transport provided vport create function.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The patch includes the driver side changes to enable basic PBC (PreBoot
Configuration) feature.
- Data structure changes and new definitions for PBC.
- APIs to access PBC info.
- Remove unused code.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch enables support of new mezzanine cards for HP and IBM blade server.

- Add new pciids for HP and IBM mezzanine card.
- Add a new firmware image for HP mezzanine card, which is running in
  FC only mode. Rename firmware image to reflect the difference. Change the
  firmware download code accordingly for the above changes.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

[Ss]ytem => [Ss]ystem
udpate => update
paramters => parameters
orginal => original
Signed-off-by: NThomas Weber <swirl@gmx.li>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

MS module did not invoke fdmi offline in all cases,
call fdmi offline when ms module receives a port offline,
so that fdmi offline is from one place in the ms module.

Make changes to handle 10G speed in the conversion routine.

Replaced the usage of bfa_adapter_attr_s struct with specific API's.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Modified the portstats get/clear logic for port physical/FCoE/QoS stats.
Added more stats to FC
Fixed some issues with FCoE stats collection.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfa_ioc_attr_s is a big structure and some times could cause
stack overflow if defined locally, so add specific APIs that
are needed to replace the use of ioc_attr local var.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Rename pport structures to fcport in BFA FCS, to resolve confusion
about the port structures in the firmware, and make sure the SG page
is setup correctly.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Replace enum types with int and rearrange the fields to fix some
alignment issue.

Local var ioc_attr is causing the stack to overflow, so removed the
usage of the local ioc_attr var and now invoking an API to return the
ioc_type.

Fix some AEN issues.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Made FCS authentication related changes to state machines and header
files.

Made changes in FCS state machines to handle the case when secret
string is NULL.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Changed PCI VPD to incorporate specific OEM vendors.

Added FCoE specific interrupt latency and delay params.

Added some variables needed by FIP 2.0.

Added some new logging and tracing definitions.

Added reserved members to make the structures (IOC, IOCFC) 64bit aligned.

Changed the module identifiers, as some files were moved.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Copy fpma MAC when requested by user space application.  Added FPMA
mac address to the lport attributes structure.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Clear LL_HALT and PSS_ERR bit in the interrupt status register on an IOC crash.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add support for faster IOC recovery after failure.

Split bfa_ioc.c into three files:
  bfa_ioc.c:    Common code shared between crossbow and catapult ASIC's.

  bfa_ioc_cb.c: Code specific to the crossbow, reg mapping and
                interrupt related routines.

  bfa_ioc_ct.c: Code specific to the catapult, reg mapping and
                interrupt related routines.

Fix to make sure IOC reinitialize's properly on enable request -
update the ioc_fwstate reg with BFI_IOC_FAIL on ioc disable mbox cmd
timeout.

Makefile changes to support the 2 newly added files bfa_ioc_cb.c and
bfa_ioc_ct.c.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Brocade CNA currently supports only 190 vports (instead of 191),
since there are only 192 unicast cam entries reserved for FCoE.

Brocade CNA has a total of 256 unicast cam entries (192 FCoE + 64 LL)

192 cam entries = 1 burned in mac + 1 baseport FPMA mac + 190 vport
FPMA macs.

Made changes to the code to support only 190 vports.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Split bfa_fcs_init() into bfa_fcs_attach() and bfa_fcs_init().

Removed empty function definitions in FCS modules

Modified driver to call bfa_fcs_attach() and bfa_fcs_init() as needed.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

 Added a FCS function to be called during driver init, to set the FDMI
 Driver parameter.

fdmi.c: Created a disabled state when fdmi is disabled.

bfad.c:
  * Added fdmi_enable driver parameter.
  * Added support to call bfa_fcs_set_fdmi_param() to initialize fcs
    fdmi setting.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfa_intr.c:  Enable new halt interrupt in BFA.
bfi_ctreg.h: Expose new halt interrupt bit definition to host.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Clear virtual links was not propagated upwards to bfa from fw.
This resulted in HBA and switch being in an inconsistent state.

So defined a new LPS event for clear virtual link on a vport,
and also now clear virtual link on a baseport, is sent as a
link down event from the fw.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: NAdam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch fixes checkpatch errors/warnings in bfad files.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add new driver for Brocade Hardware
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>