Rx indirection table entries are in the range [0, (rss_count - 1)]. If
user reduces the rss count, the table entries may not be in the ccorrect
range. Need to reconfigure the table with new rss_count as a basis.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the current default values for Rx path i.e., 8 queues of 8Kb entries
each with 4Kb size, interface will consume 256Mb for Rx. The default values
causing the driver probe to fail when the system memory is low. Based on
the perforamnce results, rx-ring count value of 1Kb gives the comparable
performance with Rx coalesce timeout of 12 seconds. Updating the default
values.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the execution of loopback test, driver may receive the packets which
are not originated by this test, loopback implementation need to skip those
packets.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RSS configuration is not supported for 100G adapters.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes in kernel ethtool implementation requires the driver
callback for get_channels() has to populate the values for max tx/rx
coalesce fields.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit a681574c
("ipv4: disable BH in set_ping_group_range()") because we never
read ping_group_range in BH context (unlike local_port_range).

Then, since we already have a lock for ping_group_range, those
using ip_local_ports.lock for ping_group_range are clearly typos.

We might consider to share a same lock for both ping_group_range
and local_port_range w.r.t. space saving, but that should be for
net-next.

Fixes: a681574c ("ipv4: disable BH in set_ping_group_range()")
Fixes: ba6b918a ("ping: move ping_group_range out of CONFIG_SYSCTL")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Eric Salo <salo@google.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Do not rely on kexec_in_progress

These are the two patches following the discussing we had on kexec_in_progress.

Feel free to apply or discard them, thanks!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After discussing with Eric, it turns out that, while using
kexec_in_progress is a nice optimization, which prevents us from always
powering on the integrated PHY, let's just turn it on in the shutdown
path.

This removes a dependency on kexec_in_progress which, according to Eric
should not be used by modules

Fixes: 2399d614 ("net: dsa: bcm_sf2: Prevent GPHY shutdown for kexec'd kernels")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 97dcaa0f. Based on
the review discussion with Eric, we will come up with a different fix
for the bcm_sf2 driver which does not make it rely on the
kexec_in_progress value.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit bc51dddf ("netns: avoid disabling irq for
netns id") as it was found to cause problems with systems running
SELinux/audit, see the mailing list thread below:

 * http://marc.info/?t=147694653900002&r=1&w=2

Eventually we should be able to reintroduce this code once we have
rewritten the audit multicast code to queue messages much the same
way we do for unicast messages.  A tracking issue for this can be
found below:

 * https://github.com/linux-audit/audit-kernel/issues/23Reported-by: NStephen Smalley <sds@tycho.nsa.gov>
Reported-by: NElad Raz <e@eladraz.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NPaul Moore <paul@paul-moore.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Baozeng reported this deadlock case:

       CPU0                    CPU1
       ----                    ----
  lock([  165.136033] sk_lock-AF_INET6);
                               lock([  165.136033] rtnl_mutex);
                               lock([  165.136033] sk_lock-AF_INET6);
  lock([  165.136033] rtnl_mutex);

Similar to commit 87e9f031
("ipv4: fix a potential deadlock in mcast getsockopt() path")
this is due to we still have a case, ipv6_sock_mc_close(),
where we acquire sk_lock before rtnl_lock. Close this deadlock
with the similar solution, that is always acquire rtnl lock first.

Fixes: baf606d9 ("ipv4,ipv6: grab rtnl before locking the socket")
Reported-by: NBaozeng Ding <sploving1@gmail.com>
Tested-by: NBaozeng Ding <sploving1@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Fix compilation warning in xt_hashlimit on m68k 32-bits, from
   Geert Uytterhoeven.

2) Fix wrong timeout in set elements added from packet path via
   nft_dynset, from Anders K. Pedersen.

3) Remove obsolete nf_conntrack_events_retry_timeout sysctl
   documentation, from Nicolas Dichtel.

4) Ensure proper initialization of log flags via xt_LOG, from
   Liping Zhang.

5) Missing alias to autoload ipcomp, also from Liping Zhang.

6) Missing NFTA_HASH_OFFSET attribute validation, again from Liping.

7) Wrong integer type in the new nft_parse_u32_check() function,
   from Dan Carpenter.

8) Another wrong integer type declaration in nft_exthdr_init, also
   from Dan Carpenter.

9) Fix insufficient mode validation in nft_range.

10) Fix compilation warning in nft_range due to possible uninitialized
    value, from Arnd Bergmann.

11) Zero nf_hook_ops allocated via xt_hook_alloc() in x_tables to
    calm down kmemcheck, from Florian Westphal.

12) Schedule gc_worker() to run again if GC_MAX_EVICTS quota is reached,
    from Nicolas Dichtel.

13) Fix nf_queue() after conversion to single-linked hook list, related
    to incorrect bypass flag handling and incorrect hook point of
    reinjection.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bcm_sf2 driver uses kexec_in_progress to know whether it can power
down an integrated PHY during shutdown, and can be built as a module.
Other modules may be using this in the future, so export it.

Fixes: 2399d614 ("net: dsa: bcm_sf2: Prevent GPHY shutdown for kexec'd kernels")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 4ee3bd4a ("ipv4: disable BH when changing ip local port
range") Cong added BH protection in set_local_port_range() but missed
that same fix was needed in set_ping_group_range()

Fixes: b8f1a556 ("udp: Add function to make source port for UDP tunnels")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NEric Salo <salo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Baozeng Ding reported KASAN traces showing uses after free in
udp_lib_get_port() and other related UDP functions.

A CONFIG_DEBUG_PAGEALLOC=y kernel would eventually crash.

I could write a reproducer with two threads doing :

static int sock_fd;
static void *thr1(void *arg)
{
	for (;;) {
		connect(sock_fd, (const struct sockaddr *)arg,
			sizeof(struct sockaddr_in));
	}
}

static void *thr2(void *arg)
{
	struct sockaddr_in unspec;

	for (;;) {
		memset(&unspec, 0, sizeof(unspec));
	        connect(sock_fd, (const struct sockaddr *)&unspec,
			sizeof(unspec));
        }
}

Problem is that udp_disconnect() could run without holding socket lock,
and this was causing list corruptions.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NBaozeng Ding <sploving1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For a kernel that is being kexec'd we re-enable the integrated GPHY in
order for the subsequent MDIO bus scan to succeed and properly bind to
the bcm7xxx PHY driver. If we did not do that, the GPHY would be shut
down by the time the MDIO driver is probing the bus, and it would fail
to read the correct PHY OUI and therefore bind to an appropriate PHY
driver. Later on, this would cause DSA not to be able to successfully
attach to the PHY, and the interface would not be created at all.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 636c2628 ("net: skbuff: Remove errornous length
validation in skb_vlan_pop()") mentioned test case stopped working,
throwing a -12 (ENOMEM) return code. The issue however is not due to
636c2628, but rather due to a buggy test case that got uncovered
from the change in behaviour in 636c2628.

The data_size of that test case for the skb was set to 1. In the
bpf_fill_ld_abs_vlan_push_pop() handler bpf insns are generated that
loop with: reading skb data, pushing 68 tags, reading skb data,
popping 68 tags, reading skb data, etc, in order to force a skb
expansion and thus trigger that JITs recache skb->data. Problem is
that initial data_size is too small.

While before 636c2628, the test silently bailed out due to the
skb->len < VLAN_ETH_HLEN check with returning 0, and now throwing an
error from failing skb_ensure_writable(). Set at least minimum of
ETH_HLEN as an initial length so that on first push of data, equivalent
pop will succeed.

Fixes: 4d9c5c53 ("test_bpf: add bpf_skb_vlan_push/pop() tests")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, GRO can do unlimited recursion through the gro_receive
handlers.  This was fixed for tunneling protocols by limiting tunnel GRO
to one level with encap_mark, but both VLAN and TEB still have this
problem.  Thus, the kernel is vulnerable to a stack overflow, if we
receive a packet composed entirely of VLAN headers.

This patch adds a recursion counter to the GRO layer to prevent stack
overflow.  When a gro_receive function hits the recursion limit, GRO is
aborted for this skb and it is processed normally.  This recursion
counter is put in the GRO CB, but could be turned into a percpu counter
if we run out of space in the CB.

Thanks to Vladimír Beneš <vbenes@redhat.com> for the initial bug report.

Fixes: CVE-2016-7039
Fixes: 9b174d88 ("net: Add Transparent Ethernet Bridging GRO support.")
Fixes: 66e5133f ("vlan: Add GRO support for non hardware accelerated vlan")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Reviewed-by: NJiri Benc <jbenc@redhat.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check for an underflow of tmp_prefered_lft is always false
because tmp_prefered_lft is unsigned. The intention of the check
was to guard against racing with an update of the
temp_prefered_lft sysctl, potentially resulting in an underflow.

As suggested by David Miller, the best way to prevent the race is
by reading the sysctl variable using READ_ONCE.
Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Reported-by: NJulia Lawall <julia.lawall@lip6.fr>
Fixes: 76506a98 ("IPv6: fix DESYNC_FACTOR")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nf_queue handling is broken since e3b37f11 ("netfilter: replace
list_head with single linked list") for two reasons:

1) If the bypass flag is set on, there are no userspace listeners and
   we still have more hook entries to iterate over, then jump to the
   next hook. Otherwise accept the packet. On nf_reinject() path, the
   okfn() needs to be invoked.

2) We should not re-enter the same hook on packet reinjection. If the
   packet is accepted, we have to skip the current hook from where the
   packet was enqueued, otherwise the packets gets enqueued over and
   over again.

This restores the previous list_for_each_entry_continue() behaviour
happening from nf_iterate() that was dealing with these two cases.
This patch introduces a new nf_queue() wrapper function so this fix
becomes simpler.

Fixes: e3b37f11 ("netfilter: replace list_head with single linked list")
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

When the maximum evictions number is reached, do not wait 5 seconds before
the next run.

CC: Florian Westphal <fw@strlen.de>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

It makes sense to display the descriptors even if
DES0 is zero. This helps for example in case of it
is needed to dump rx write-back descriptors to get
timestamp status.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gavin Shan says:

====================
net/ncsi: More bug fixes

This series fixes 2 issues that were found during NCSI's availability
testing on BCM5718 and improves HNCDSC AEN handler:

   * PATCH[1] refactors the code so that minimal code change is put
     to PATCH[2].
   * PATCH[2] fixes the NCSI channel's stale link state before doing
     failover.
   * PATCH[3] chooses the hot channel, which was ever chosen as active
     channel, when the available channels are all in link-down state.
   * PATCH[4] improves Host Network Controller Driver Status Change
     (HNCDSC) AEN handler

Changelog
=========
v2:
   * Merged PATCH[v1 1/2] to PATCH[v2 1].
   * Avoid if/else statements in ncsi_suspend_channel() as Joel suggested.
   * Added comments to explain why we need retrieve last link states in
     ncsi_suspend_channel().
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This improves AEN handler for Host Network Controller Driver Status
Change (HNCDSC):

   * The channel's lock should be hold when accessing its state.
   * Do failover when host driver isn't ready.
   * Configure channel when host driver becomes ready.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. C0 is in link-up state while C1 is in link-down
state. C0 is chosen as active channel until unplugging and plugging
C0's cable:  On unplugging C0's cable, LSC (Link State Change) AEN
packet received on C0 to report link-down event. After that, C1 is
chosen as active channel. LSC AEN for link-up event is lost on C0
when plugging C0's cable back. We lose the network even C0 is usable.

This resolves the issue by recording the (hot) channel that was ever
chosen as active one. The hot channel is chosen to be active one
if none of available channels in link-up state. With this, C0 is still
the active one after unplugging C0's cable. LSC AEN packet received
on C0 when plugging its cable back.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. Both of them are connected to different LANs,
means they are in link-up state and C0 is chosen as the active one
until resetting BCM5718 happens as below.

Resetting BCM5718 results in LSC (Link State Change) AEN packet
received on C0, meaning LSC AEN is missed on C1. When LSC AEN packet
received on C0 to report link-down, it fails over to C1 because C1
is in link-up state as software can see. However, C1 is in link-down
state in hardware. It means the link state is out of synchronization
between hardware and software, resulting in inappropriate channel (C1)
selected as active one.

This resolves the issue by sending separate GLS (Get Link Status)
commands to all channels in the package before trying to do failover.
The last link states of all channels in the package are retrieved.
With it, C0 (not C1) is selected as active one as expected.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several if/else statements in the state machine implemented
by switch/case in ncsi_suspend_channel() to avoid duplicated code. It
makes the code a bit hard to be understood.

This drops if/else statements in ncsi_suspend_channel() to improve the
code readability as Joel Stanley suggested. Also, it becomes easy to
add more states in the state machine without affecting current code.
No logical changes introduced by this.
Suggested-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

stats_update callback is called by NIC drivers doing hardware
offloading of the mirred action. Lastuse is passed as argument
to specify when the stats was actually last updated and is not
always the current time.

Fixes: 9798e6fe ('net: act_mirred: allow statistic updates from offloaded actions')
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SwitchX2 firmware does not implement reset done yet. Moreover, when
busy-polled for ready magic, that slows down firmware and reset takes
longer than the defined timeout, causing initialization to fail.
So restore the previous behaviour and just sleep in this case.

Fixes: 233fa44b ("mlxsw: pci: Implement reset done check")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When creating an ethernet port fails, we must move the port to disable,
otherwise putting the port in switch partition 0 (ETH) or 1 (IB) will
always fails.

Fixes: 31557f0f ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: NElad Raz <eladr@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function return value is not checked anywhere. Also, the warning
causes huge slowdown when removing large number of FIB entries which
were not offloaded, because of ordering issue. Ido's preparing
a patchset to fix the ordering issue, but that is definitelly not
net tree material.

Fixes: b45f64d1 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By a mistake, there is tree index 0 passed to RALTB. Should be
MLXSW_SP_LPM_TREE_MIN.

Fixes: b45f64d1 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Reported-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit commit 7086605a ("stmmac: fix error check when init ptp")
breaks the procedure added by the
commit efee95f4 ("ptp_clock: future-proofing drivers against PTP
subsystem becoming optional")

So this patch tries to re-import the logic added by the latest
commit above: it makes sense to have the stmmac_ptp_register
as void function and, inside the main, the stmmac_init_ptp can fails
in case of the capability cannot be supported by the HW.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Nicolas Pitre <nico@linaro.org>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Markus Trippelsdorf reports:

WARNING: kmemcheck: Caught 64-bit read from uninitialized memory (ffff88001e605480)
4055601e0088ffff000000000000000090686d81ffffffff0000000000000000
 u u u u u u u u u u u u u u u u i i i i i i i i u u u u u u u u
 ^
|RIP: 0010:[<ffffffff8166e561>]  [<ffffffff8166e561>] nf_register_net_hook+0x51/0x160
[..]
 [<ffffffff8166e561>] nf_register_net_hook+0x51/0x160
 [<ffffffff8166eaaf>] nf_register_net_hooks+0x3f/0xa0
 [<ffffffff816d6715>] ipt_register_table+0xe5/0x110
[..]

This warning is harmless; we copy 'uninitialized' data from the hook ops
but it will not be used.
Long term the structures keeping run-time data should be disentangled
from those only containing config-time data (such as where in the list
to insert a hook), but thats -next material.
Reported-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Suggested-by: NAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Acked-by: NAaron Conole <aconole@bytheb.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Since commit b2fb4f54 ("tcp: uninline tcp_prequeue()") we no longer
access sysctl_tcp_low_latency from a module.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The offload flag is a status flag and should not be used by
FIB semantics for comparison.

Fixes: 37ed9493 ("rtnetlink: add RTNH_F_EXTERNAL flag for fib offload")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We recently got the following warning after setting up a vlan device on
top of an offloaded bridge and executing 'bridge link':

WARNING: CPU: 0 PID: 18566 at drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:81 mlxsw_sp_port_orig_get.part.9+0x55/0x70 [mlxsw_spectrum]
[...]
 CPU: 0 PID: 18566 Comm: bridge Not tainted 4.8.0-rc7 #1
 Hardware name: Mellanox Technologies Ltd. Mellanox switch/Mellanox switch, BIOS 4.6.5 05/21/2015
  0000000000000286 00000000e64ab94f ffff880406e6f8f0 ffffffff8135eaa3
  0000000000000000 0000000000000000 ffff880406e6f930 ffffffff8108c43b
  0000005106e6f988 ffff8803df398840 ffff880403c60108 ffff880406e6f990
 Call Trace:
  [<ffffffff8135eaa3>] dump_stack+0x63/0x90
  [<ffffffff8108c43b>] __warn+0xcb/0xf0
  [<ffffffff8108c56d>] warn_slowpath_null+0x1d/0x20
  [<ffffffffa01420d5>] mlxsw_sp_port_orig_get.part.9+0x55/0x70 [mlxsw_spectrum]
  [<ffffffffa0142195>] mlxsw_sp_port_attr_get+0xa5/0xb0 [mlxsw_spectrum]
  [<ffffffff816f151f>] switchdev_port_attr_get+0x4f/0x140
  [<ffffffff816f15d0>] switchdev_port_attr_get+0x100/0x140
  [<ffffffff816f15d0>] switchdev_port_attr_get+0x100/0x140
  [<ffffffff816f1d6b>] switchdev_port_bridge_getlink+0x5b/0xc0
  [<ffffffff816f2680>] ? switchdev_port_fdb_dump+0x90/0x90
  [<ffffffff815f5427>] rtnl_bridge_getlink+0xe7/0x190
  [<ffffffff8161a1b2>] netlink_dump+0x122/0x290
  [<ffffffff8161b0df>] __netlink_dump_start+0x15f/0x190
  [<ffffffff815f5340>] ? rtnl_bridge_dellink+0x230/0x230
  [<ffffffff815fab46>] rtnetlink_rcv_msg+0x1a6/0x220
  [<ffffffff81208118>] ? __kmalloc_node_track_caller+0x208/0x2c0
  [<ffffffff815f5340>] ? rtnl_bridge_dellink+0x230/0x230
  [<ffffffff815fa9a0>] ? rtnl_newlink+0x890/0x890
  [<ffffffff8161cf54>] netlink_rcv_skb+0xa4/0xc0
  [<ffffffff815f56f8>] rtnetlink_rcv+0x28/0x30
  [<ffffffff8161c92c>] netlink_unicast+0x18c/0x240
  [<ffffffff8161ccdb>] netlink_sendmsg+0x2fb/0x3a0
  [<ffffffff815c5a48>] sock_sendmsg+0x38/0x50
  [<ffffffff815c6031>] SYSC_sendto+0x101/0x190
  [<ffffffff815c7111>] ? __sys_recvmsg+0x51/0x90
  [<ffffffff815c6b6e>] SyS_sendto+0xe/0x10
  [<ffffffff817017f2>] entry_SYSCALL_64_fastpath+0x1a/0xa4

The problem is that the 8021q module propagates the call to
ndo_bridge_getlink() via switchdev ops, but the switch driver doesn't
recognize the netdev, as it's not offloaded.

While we can ignore calls being made to non-bridge ports inside the
driver, a better fix would be to push this check up to the switchdev
layer.

Note that these ndos can be called for non-bridged netdev, but this only
happens in certain PF drivers which don't call the corresponding
switchdev functions anyway.

Fixes: 99f44bb3 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NTamir Winetroub <tamirw@mellanox.com>
Tested-by: NTamir Winetroub <tamirw@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tamir reported the following trace when processing ARP requests received
via a vlan device on top of a VLAN-aware bridge:

 NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [swapper/1:0]
[...]
 CPU: 1 PID: 0 Comm: swapper/1 Tainted: G        W       4.8.0-rc7 #1
 Hardware name: Mellanox Technologies Ltd. "MSN2100-CB2F"/"SA001017", BIOS 5.6.5 06/07/2016
 task: ffff88017edfea40 task.stack: ffff88017ee10000
 RIP: 0010:[<ffffffff815dcc73>]  [<ffffffff815dcc73>] netdev_all_lower_get_next_rcu+0x33/0x60
[...]
 Call Trace:
  <IRQ>
  [<ffffffffa015de0a>] mlxsw_sp_port_lower_dev_hold+0x5a/0xa0 [mlxsw_spectrum]
  [<ffffffffa016f1b0>] mlxsw_sp_router_netevent_event+0x80/0x150 [mlxsw_spectrum]
  [<ffffffff810ad07a>] notifier_call_chain+0x4a/0x70
  [<ffffffff810ad13a>] atomic_notifier_call_chain+0x1a/0x20
  [<ffffffff815ee77b>] call_netevent_notifiers+0x1b/0x20
  [<ffffffff815f2eb6>] neigh_update+0x306/0x740
  [<ffffffff815f38ce>] neigh_event_ns+0x4e/0xb0
  [<ffffffff8165ea3f>] arp_process+0x66f/0x700
  [<ffffffff8170214c>] ? common_interrupt+0x8c/0x8c
  [<ffffffff8165ec29>] arp_rcv+0x139/0x1d0
  [<ffffffff816e505a>] ? vlan_do_receive+0xda/0x320
  [<ffffffff815e3794>] __netif_receive_skb_core+0x524/0xab0
  [<ffffffff815e6830>] ? dev_queue_xmit+0x10/0x20
  [<ffffffffa06d612d>] ? br_forward_finish+0x3d/0xc0 [bridge]
  [<ffffffffa06e5796>] ? br_handle_vlan+0xf6/0x1b0 [bridge]
  [<ffffffff815e3d38>] __netif_receive_skb+0x18/0x60
  [<ffffffff815e3dc0>] netif_receive_skb_internal+0x40/0xb0
  [<ffffffff815e3e4c>] netif_receive_skb+0x1c/0x70
  [<ffffffffa06d7856>] br_pass_frame_up+0xc6/0x160 [bridge]
  [<ffffffffa06d63d7>] ? deliver_clone+0x37/0x50 [bridge]
  [<ffffffffa06d656c>] ? br_flood+0xcc/0x160 [bridge]
  [<ffffffffa06d7b14>] br_handle_frame_finish+0x224/0x4f0 [bridge]
  [<ffffffffa06d7f94>] br_handle_frame+0x174/0x300 [bridge]
  [<ffffffff815e3599>] __netif_receive_skb_core+0x329/0xab0
  [<ffffffff81374815>] ? find_next_bit+0x15/0x20
  [<ffffffff8135e802>] ? cpumask_next_and+0x32/0x50
  [<ffffffff810c9968>] ? load_balance+0x178/0x9b0
  [<ffffffff815e3d38>] __netif_receive_skb+0x18/0x60
  [<ffffffff815e3dc0>] netif_receive_skb_internal+0x40/0xb0
  [<ffffffff815e3e4c>] netif_receive_skb+0x1c/0x70
  [<ffffffffa01544a1>] mlxsw_sp_rx_listener_func+0x61/0xb0 [mlxsw_spectrum]
  [<ffffffffa005c9f7>] mlxsw_core_skb_receive+0x187/0x200 [mlxsw_core]
  [<ffffffffa007332a>] mlxsw_pci_cq_tasklet+0x63a/0x9b0 [mlxsw_pci]
  [<ffffffff81091986>] tasklet_action+0xf6/0x110
  [<ffffffff81704556>] __do_softirq+0xf6/0x280
  [<ffffffff8109213f>] irq_exit+0xdf/0xf0
  [<ffffffff817042b4>] do_IRQ+0x54/0xd0
  [<ffffffff8170214c>] common_interrupt+0x8c/0x8c

The problem is that netdev_all_lower_get_next_rcu() never advances the
iterator, thereby causing the loop over the lower adjacency list to run
forever.

Fix this by advancing the iterator and avoid the infinite loop.

Fixes: 7ce856aa ("mlxsw: spectrum: Add couple of lower device helper functions")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NTamir Winetroub <tamirw@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes a panic when calling eth_get_headlen(). Noticed on i40e driver.

Fixes: d5709f7a ("flow_dissector: For stripped vlan, get vlan info from skb->vlan_tci")
Signed-off-by: NEric Garver <e@erig.me>
Reviewed-by: NJakub Sitnicki <jkbs@redhat.com>
Acked-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>