A lot of EH codes are about to be added to libata.  Separate out
libata-eh.c.  ata_scsi_timed_out(), ata_scsi_error(),
ata_qc_timeout(), ata_eng_timeout(), ata_eh_qc_complete() and
ata_eh_qc_retry() are moved.  No code is changed by this patch.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

qcs might get retried because of unrelated failure.  e.g. NCQ command
failure causes the whole command set to be aborted.  Decrement
scmd->retries for such retrials to avoid unnecessarily failing
commands.  Note that scmd->retries will be incremented the first time.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add @cdb to ata_exec_internal().  It will be used by new EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

TF register might not be directly accessible depending on errors.
e.g. TF of failed NCQ command is in log page 10h.  Make reading TF
responsibility of error handlers.  For the current EH, simply push TF
reading into qc completion functions as they are practically part of
EH.  New EH will fill qc->tf with status registers before complting
qcs.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Current sense generation code does not generate sense error if status
register value doesn't indicate error condition.  However, LLDD's may
indicate errors which 't show up in status register.  Completing such
qc's without generating sense results in successful completion of
failed commands.

Invoke ata_to_sense_error() regardless of status register if
qc->err_mask is not zero such that ata_to_sense_error() generates
default sense error.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The current code passes pointer to ap around and repeatedly performs
ata_qc_from_tag() to access the ongoing qc.  This is unnatural and
makes EH synchronization cumbersome.  Make PIO codes deal with qc
instead of ap.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add a new qc flag ATA_QCFLAG_IO.  This flag gets set for normal IO
commands originating from SCSI midlayer.  This information will be
used by EH to determine transfer speed reconfiguration.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_dev_set_mode() is now responsible for managing ATA_DFLAG_PIO.
Clear it before setting it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_dev_configure() should not clear dynamic device flags determined
elsewhere.  Lower eight bits are reserved for feature flags, define
ATA_DFLAG_CFG_MASK and clear only those bits before configuring
device.  Without this patch, ATA_DFLAG_PIO gets turned off during
revalidation making PIO mode unuseable.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rename ATA_FLAG_PORT_DISABLED to ATA_FLAG_DISABLED for consistency.
(ATA_FLAG_* are always about ports).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* Reorder ATA_DFLAG_* such that feature flags determined by
  ata_dev_configure() are on lower bits.  Reserve lower eight bits
  for this purpose and allocate dynamic flags from bit 8.

* Reorder ATA_FLAG_* such that feature flags determined during driver
  initiailization are on bits 0:15, dynamic flags on 16:23 and LLDD
  specific flags on 24:31.

* Kill trailing white space and lower-case an one line comment for
  consistency.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Kill unused flag ATA_FLAG_IN_EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure ata_dev_revalidate() complains on failures and kill
revalidation failure message printed from ata_dev_set_mode().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Report device number on PIO failure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_bus_probe() now marks failed devices properly and leaves
meaningful transfer mode masks.  This patch makes ata_dev_xfermask()
consider disable devices when determining PIO mode to avoid violating
device selection timing.

While at it, move port-wide resttriction out of device iteration loop
and try to make the function look a bit prettier.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Improve ata_bus_probe() such that configuration failures are handled
better.  Each device is given ATA_PROBE_MAX_TRIES chances, but any
non-transient error (revalidation failure with -ENODEV, configuration
failure with -EINVAL...) disables the device directly.  Any IO error
results in SATA PHY speed down and ata_set_mode() failure lowers
transfer mode.  The last try always puts a device into PIO-0.

After each failure, the whole port is reset to make sure that the
controller and all the devices are in a known and stable state.  The
reset also applies SATA SPD configuration if necessary.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement ata_down_xfermask_limit().  This function manipulates
@dev->pio/mwdma/udma_mask such that the next lower transfer mode is
selected.  This will be used to improve ata_bus_probe() failure
handling and later by EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some devices react badly if resets are performed back-to-back.  Give
devices some time to breath and tell user that we're taking a nap.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_drive_probe_reset() use SATA SPD configuration.  Hardreset
will be force if speed renegotiation is necessary.  Also, if a
hardreset fails, PHY speed is stepped down and hardreset is retried
until the lowest speed is reached.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ap->sata_spd_limit contrains SATA PHY speed of the port.  It is
initialized to the configured value prior to probing thus preserving
BIOS configured value.  hardreset is responsible for applying SPD
limit and sata_std_hardreset() is updated to do that.  SATA SPD limit
will be used to enhance failure handling during probing and later by
EH.

This patch also normalizes some comments around affected code.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

For the time being we cannot use ata_dev_present() as it was renamed
to ata_dev_enabled() but we still need presence test.  Implement
negation of the test.  Conveniently, the negated result is needed in
more places.  This is suggested by Jeff Garzik.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't overwrite SPD setting during hard reset.  This change has the
(intended) side effect of honoring the BIOS configuration.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When ata_set_mode() fails on a device, make ata_set_mode() return
error code and pointer to the device instead of disabling it directly.
This gives more control to higher level driving logic.

This patch does not change the end result (configured transfer mode)
although it may make libata repeat mode configuration to the peer of a
failing device.  Later ata_bus_probe() rewrite will make full use of
this change.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge ata_host_set_pio() and ata_host_set_dma() into ata_set_mode()
and use function-level *dev to iterate over devices.  This eases
soon-to-follow ata_set_mode() interface change.

While at it, kill an unnecessary comment and normalize others.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_set_mode() return without doing anything if there is no
device on the port.  This is in preparation for ata_bus_probe()
changes.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch renames ata_dev_present() to ata_dev_enabled() and adds
ata_dev_disabled().  This is to discern the state where a device is
present but disabled from not-present state.  This disctinction is
necessary when configuring transfer mode because device selection
timing must not be violated even if a device fails to configure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make do_probe_reset() generic by pushing classification check into
ata_drive_probe_reset() and rename it to ata_do_reset().  This will be
used by EH reset.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Separate out ata_spd_string() from sata_print_link_status().  This
will be used by SATA spd configuration routines.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_bus_probe() uses unsigned int rc to receive negative errno and
returns the converted unsigned int value.  Convert temporary variables
to int and make ata_bus_probe() return negative errno on failure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_set_mode() return correct error value when ata_dev_set_mode()
fails.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* master.kernel.org:/home/rmk/linux-2.6-serial:
  [SERIAL] Allow 8250 PCI, PNP, GSC and HP300 support to be disabled

* master.kernel.org:/home/rmk/linux-2.6-mmc:
  [MMC] Pass -DDEBUG on compiler command line if MMC_DEBUG selected
  [MMC] Add OMAP MMC host driver

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 3424/2: ixp23xx: fix uncompress.h for recent CRLF decompressor change
  [ARM] 3434/1: pxa i2s amsl define
  [ARM] 3425/1: xsc3: need to include pgtable-hwdef.h
  [ARM] Allow un-muxed syscalls to be available for everyone
  [ARM] 3420/1: Missing clobber in example code
  [ARM] nommu: fixups for the exception vectors
  [ARM] nommu: add nommu specific Kconfig and MMUEXT variable in Makefile
  [ARM] nommu: start-up code
  [ARM] nommu: MPU support in boot/compressed/head.S

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Avoid "u64 foo : 32;" for gcc3 vs. gcc4 compatibility
  [IA64] Export cpu cache info by sysfs

* master.kernel.org:/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] Fix typo in earlier cifs_unlink change and protect one
  [CIFS] Incorrect signature sent on SMB Read
  [CIFS] Fix unlink oops when indirectly called in rename error path
  [CIFS] Fix two remaining coverity scan tool warnings.
  [CIFS] Set correct lock type on new posix unlock call
  [CIFS] Upate cifs change log
  [CIFS] Fix slow oplock break response when mounts to different
  [CIFS] Workaround various server bugs found in testing at connectathon
  [CIFS] Allow fallback for setting file size to Procom SMB server when
  [CIFS] Make POSIX CIFS Extensions SetFSInfo match exactly what we want
  [CIFS] Move noisy debug message (triggerred by some older servers) from
  [CIFS] Use correct pid on new cifs posix byte range lock call
  [CIFS] Add posix (advisory) byte range locking support to cifs client
  [CIFS] CIFS readdir perf optimizations part 1
  [CIFS] Free small buffers earlier so we exceed the cifs
  [CIFS] Fix large (ie over 64K for MaxCIFSBufSize) buffer case for wrapping
  [CIFS] Convert remaining places in fs/cifs from
  [CIFS] SessionSetup cleanup part 2
  [CIFS] fix compile error (typo) and warning in cifssmb.c
  [CIFS] Cleanup NTLMSSP session setup handling

extra path.

Since cifs_unlink can also be called from rename path and there
was one report of oops am making the extra check for null inode.
Signed-off-by: NSteve French <sfrench@us.ibm.com>

Fixes Samba bug 3621 and kernel.org bug 6147

For servers which require SMB/CIFS packet signing, we were sending the
wrong signature (all zeros) on SMB Read request.  The new cifs routine
to do signatures across an iovec was not complete - and SMB Read, unlike
the new SMBWrite2, did not fall back to the older routine (ie use
SendReceive vs. the more efficient SendReceive2 ie used the older
cifs_sign_smb vs. the disabled  cifs_sign_smb2) for calculating signatures.

This finishes up cifs_sign_smb2/cifs_calc_signature2 so that the callers
of SendReceive2 can get SMB/CIFS packet signatures.

Now that cifs_sign_smb2 is supported, we could start using it in
the write path but this smaller fix does not include the change
to use SMBWrite2 when signatures are required (which when enabled
will make more Writes more efficient and alloc less memory).
Currently Write2 is only used when signatures are not
required at the moment but after more testing we will enable
that as well).

Thanks to James Slepicka and Sam Flory for initial investigation.
Signed-off-by: NSteve French <sfrench@us.ibm.com>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET]: Allow skb headroom to be overridden
  [TCP]: Kill unused extern decl for tcp_v4_hash_connecting()
  [NET]: add SO_RCVBUF comment
  [NET]: Deinline some larger functions from netdevice.h
  [DCCP]: Use NULL for pointers, comfort sparse.
  [DECNET]: Fix refcount

Commit 70674f95:

  [PATCH] Optimize select/poll by putting small data sets on the stack

resulted in the poll stack being 4-byte aligned on 64-bit architectures,
causing misaligned accesses to elements in the array.

This patch fixes it by declaring the stack in terms of 'long' instead
of 'char'.

Force alignment of poll and select stacks to long to avoid unaligned
access on 64 bit architectures.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] libata: fix ata_xfer_tbl termination
  [PATCH] libata: make ata_qc_issue complete failed qcs
  [PATCH] libata: fix ata_qc_issue failure path
  [PATCH] ata_piix: fix ich6/m_map_db
  [libata] ahci: add ATI SB600 PCI IDs