Conflicts:
	drivers/acpi/pci_irq.c

Note that this merge disables
e1d3a908
pci, acpi: reroute PCI interrupt to legacy boot interrupt equivalent
Signed-off-by: NLen Brown <len.brown@intel.com>

Conflicts:
	include/acpi/acpixf.h
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

also, delete sleep/ and delete ACPI_CFLAGS from Makefile
Signed-off-by: NLen Brown <len.brown@intel.com>

when CONFIG_RTC_DRV_CMOS=m
and thus !defined(HAVE_ACPI_LEGACY_ALARM)

drivers/acpi/proc.c:85: warning: ‘cmos_bcd_read’ declared ‘static’ but
never defined
Signed-off-by: NLen Brown <len.brown@intel.com>

On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
   a. 32/64X address mismatch
   b. The 32/64X FACS address mismatch

   In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.

http://bugzilla.kernel.org/show_bug.cgi?id=8246Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

The Cx Register address obtained from the _CST object is used as the MWAIT
hints if the register type is FFixedHW. And it is used to check whether
the Cx type is supported or not.

On some boxes the following Cx state package is obtained from _CST object:
    >{
                ResourceTemplate ()
                {
                    Register (FFixedHW,
                        0x01,               // Bit Width
                        0x02,               // Bit Offset
                        0x0000000000889759, // Address
                        0x03,               // Access Size
                        )
                },

                0x03,
                0xF5,
                0x015E }

   In such case we should use the bit[7:4] of Cx address to check whether
the Cx type is supported or not.

mask the MWAIT hint to avoid array address overflow
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Acked-by: NVenki Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

GBLS and GBLL only differ in the clearing of the GHKS flag, so there is no need
to have two backlight level readouts. Also, per Peter Gruber, the need for the
BLNF check has disappeared.
As a result, cleanups can be made in the code. This has been tested on the both
the S6410 and the S6420 platforms and causes no functionality regressions, on
the console without X or within X. One module parameter to disable the hotkeys
is dropped, as we only ever took one codepath anyway.
Signed-off-by: NTony Vroon <tony@linx.net>
Tested-by: NPeter Gruber <nokos@gmx.net>
Tested-By: NStephen Gildea <stepheng+linux@gildea.com>
Acked-by: NJonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: NLen Brown <len.brown@intel.com>

The FUNC interface in the Fujitsu-Siemens DSDT was unused until now. It exposes
state information that is now reported in additional platform files (whether the
radios are killed by the hardware switch or operational, whether the machine is
docked and whether the lid is open).
Support for the backlight class is now extended with the ability to power the
backlight on & off. Optional support for the LED class allows the keyboard
headlamps found on the U810 netbook and the Fujitsu logo illumination on the
P8010 notebook to be turned on & off.

This was fed through checkpatch.pl and tested on the S6420, P8010 & U810 platforms.
Signed-off-by: NStephen Gildea <stepheng+linux@gildea.com>
Tested-by: NStephen Gildea <stepheng+linux@gildea.com>
Tested-by: NJulian Brown <jules@panic.cs-bristol.org.uk>
Signed-off-by: NTony Vroon <tony@linx.net>
Tested-by: NPeter Gruber <nokos@gmx.net>
Acked-by: NJonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: NLen Brown <len.brown@intel.com>

ACPI_USE_LOCAL_CACHE will never be defined by the Linux kernel,
and thus utcache.c will always be dead code.
Signed-off-by: NLen Brown <len.brown@intel.com>

it is referenced only #ifdef ACPI_DISASSEMBLER,
which is never set by the kernel.
Signed-off-by: NLen Brown <len.brown@intel.com>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (57 commits)
  jbd2: Fix oops in jbd2_journal_init_inode() on corrupted fs
  ext4: Remove "extents" mount option
  block: Add Kconfig help which notes that ext4 needs CONFIG_LBD
  ext4: Make printk's consistently prefixed with "EXT4-fs: "
  ext4: Add sanity checks for the superblock before mounting the filesystem
  ext4: Add mount option to set kjournald's I/O priority
  jbd2: Submit writes to the journal using WRITE_SYNC
  jbd2: Add pid and journal device name to the "kjournald2 starting" message
  ext4: Add markers for better debuggability
  ext4: Remove code to create the journal inode
  ext4: provide function to release metadata pages under memory pressure
  ext3: provide function to release metadata pages under memory pressure
  add releasepage hooks to block devices which can be used by file systems
  ext4: Fix s_dirty_blocks_counter if block allocation failed with nodelalloc
  ext4: Init the complete page while building buddy cache
  ext4: Don't allow new groups to be added during block allocation
  ext4: mark the blocks/inode bitmap beyond end of group as used
  ext4: Use new buffer_head flag to check uninit group bitmaps initialization
  ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
  ext4: code cleanup
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
  [SCSI] qla2xxx: Update version number to 8.03.00-k1.
  [SCSI] qla2xxx: Add ISP81XX support.
  [SCSI] qla2xxx: Use proper request/response queues with MQ instantiations.
  [SCSI] qla2xxx: Correct MQ-chain information retrieval during a firmware dump.
  [SCSI] qla2xxx: Collapse EFT/FCE copy procedures during a firmware dump.
  [SCSI] qla2xxx: Don't pollute kernel logs with ZIO/RIO status messages.
  [SCSI] qla2xxx: Don't fallback to interrupt-polling during re-initialization with MSI-X enabled.
  [SCSI] qla2xxx: Remove support for reading/writing HW-event-log.
  [SCSI] cxgb3i: add missing include
  [SCSI] scsi_lib: fix DID_RESET status problems
  [SCSI] fc transport: restore missing dev_loss_tmo callback to LLDD
  [SCSI] aha152x_cs: Fix regression that keeps driver from using shared interrupts
  [SCSI] sd: Correctly handle 6-byte commands with DIX
  [SCSI] sd: DIF: Fix tagging on platforms with signed char
  [SCSI] sd: DIF: Show app tag on error
  [SCSI] Fix error handling for DIF/DIX
  [SCSI] scsi_lib: don't decrement busy counters when inserting commands
  [SCSI] libsas: fix test for negative unsigned and typos
  [SCSI] a2091, gvp11: kill warn_unused_result warnings
  [SCSI] fusion: Move a dereference below a NULL test
  ...

Fixed up trivial conflict due to moving the async part of sd_probe
around in the async probes vs using dev_set_name() in naming.

* 'bkl-removal' of git://git.lwn.net/linux-2.6:
  RTC: Remove the BKL.

* 'docs-next' of git://git.lwn.net/linux-2.6:
  Fix a typo in the development process document.
  Document handling of bad memory
  Document RCU and unloadable modules

Remove calls to the BKL since concurrent access is protected
by the spin lock rtc_lock.
Signed-off-by: NDavid John <davidjon@xenontk.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NJonathan Corbet <corbet@lwn.net>

Reported-by: NAníbal Monsalve Salazar <anibal@debian.org>
Signed-off-by: NJonathan Corbet <corbet@lwn.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: fix kernel-doc warnings
  regulator: catch some registration errors
  regulator: Add basic DocBook manual
  regulator: Fix some kerneldoc rendering issues
  regulator: Add missing kerneldoc
  regulator: Clean up kerneldoc warnings
  regulator: Remove extraneous kerneldoc annotations
  regulator: init/link earlier
  regulator: move set_machine_constraints after regulator device initialization
  regulator: da903x: make da903x_is_enabled return 0 or 1
  regulator: da903x: add '\n' to error messages
  regulator: sysfs attribute reduction (v2)
  regulator: code shrink (v2)
  regulator: improved mode error checks
  regulator: enable/disable refcounting
  regulator: struct device - replace bus_id with dev_name(), dev_set_name()

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (84 commits)
  wimax: fix kernel-doc for debufs_dentry member of struct wimax_dev
  net: convert pegasus driver to net_device_ops
  bnx2x: Prevent eeprom set when driver is down
  net: switch kaweth driver to netdevops
  pcnet32: round off carrier watch timer
  i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
  wimax: testing for rfkill support should also test for CONFIG_RFKILL_MODULE
  wimax: fix kconfig interactions with rfkill and input layers
  wimax: fix '#ifndef CONFIG_BUG' layout to avoid warning
  r6040: bump release number to 0.20
  r6040: warn about MAC address being unset
  r6040: check PHY status when bringing interface up
  r6040: make printks consistent with DRV_NAME
  gianfar: Fixup use of BUS_ID_SIZE
  mlx4_en: Returning real Max in get_ringparam
  mlx4_en: Consider inline packets on completion
  netdev: bfin_mac: enable bfin_mac net dev driver for BF51x
  qeth: convert to net_device_ops
  vlan: add neigh_setup
  dm9601: warn on invalid mac address
  ...

* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
  [ARM] fix pxa930_trkball build errors
  [ARM] fix netx
  [ARM] fix pnx4008
  [ARM] fix pxa
  [ARM] remove missed CLPS7500 defconfig
  [ARM] clps711x: fix warning in edb7211-mm.c
  [ARM] clps711x: fix warning in fortunet
  [ARM] fix AT91, davinci, h720x, ks8695, msm, mx2, mx3, netx, omap1, omap2, pxa, s3c
  [ARM] Fix realview build
  [ARM] 5357/1: Kirkwood: add missing ge01 tclk initialization
  [ARM] 5358/1: AT2440EVB: Use new include path of mci.h
  [ARM] 5361/1: mv78xx0: fix compilation error
  [ARM] 5360/1: Orion: fix compilation error
  [ARM] 5359/1: Kirkwood: fix compilation error
  [ARM] S3C64XX: Fix EINT group macro definition
  [ARM] Ensure CONFIG_SERIAL_SAMSUNG_UARTS is always set.
  [ARM] S3C24XX: Add gpio_to_irq implementation
  [ARM] S3C24XX: Add gpio_to_irq() facility
  [ARM] footbridge: dc21285.c warning fixes
  [ARM] footbridge: add isa_init_irq() to common header
  ...

* 'for-linus' of git://neil.brown.name/md:
  md: don't retry recovery of raid1 that fails due to error on source drive.
  md: Allow md devices to be created by name.
  md: make devices disappear when they are no longer needed.
  md: centralise all freeing of an 'mddev' in 'md_free'
  md: move allocation of ->queue from mddev_find to md_probe
  md: need another print_sb for mdp_superblock_1
  md: use list_for_each_entry macro directly
  md: raid0: make hash_spacing and preshift sector-based.
  md: raid0: Represent the size of strip zones in sectors.
  md: raid0 create_strip_zones(): Add KERN_INFO/KERN_ERR to printk's.
  md: raid0 create_strip_zones(): Make two local variables sector-based.
  md: raid0: Represent zone->zone_offset in sectors.
  md: raid0: Represent device offset in sectors.
  md: raid0_make_request(): Replace local variable block by sector.
  md: raid0_make_request(): Remove local variable chunk_size.
  md: raid0_make_request(): Replace chunksize_bits by chunksect_bits.
  md: use sysfs_notify_dirent to notify changes to md/sync_action.
  md: fix bitmap-on-external-file bug.

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: clean up the SFF code for coding style
  libata: Add 32bit PIO support
  [libata] ahci: Withdraw IGN_SERR_INTERNAL for SB800 SATA
  pata_hpt366: reimplement mode programming
  [libata] pata_hpt3x3: correct _freeze() function declaration
  libata: Add special ata_pio_need_iordy() handling for Compact Flash.
  pata_platform: __pata_platform_remove() shouldn't be in discard section
  sata_sil24: remove unused sil24_port_multiplier
  [libata] ahci: Add SATA GEN3 related messages
  ata_piix: save, use saved and restore IOCFG
  pata_ali: Fix and workaround for FIFO DMA bug
  pata_ali: force initialise a few bits
  pata_hpt3x3: Workarounds for chipset

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There is an issue in ATI SB600/SB700 SATA that PxSERR.E should not be
set on some conditions, which will lead to many SATA ODD error messages.
commit 55a61604 is the workaround.
Since SB800 fixed this HW issue, IGN_SERR_INTERNAL should be withdrawn
for SB800.
Signed-off-by: NShane Huang <shane.huang@amd.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

If a raid1 has only one working drive and it has a sector which
gives an error on read, then an attempt to recover onto a spare will
fail, but as the single remaining drive is not removed from the
array, the recovery will be immediately re-attempted, resulting
in an infinite recovery loop.

So detect this situation and don't retry recovery once an error
on the lone remaining drive is detected.

Allow recovery to be retried once every time a spare is added
in case the problem wasn't actually a media error.
Signed-off-by: NNeilBrown <neilb@suse.de>

Using sequential numbers to identify md devices is somewhat artificial.
Using names can be a lot more user-friendly.

Also, creating md devices by opening the device special file is a bit
awkward.

So this patch provides a new option for creating and naming devices.

Writing a name such as "md_home" to
    /sys/modules/md_mod/parameters/new_array
will cause an array with that name to be created.  It will appear in
/sys/block/ /proc/partitions and /proc/mdstat as 'md_home'.
It will have an arbitrary minor number allocated.

md devices that a created by an open are destroyed on the last
close when the device is inactive.
For named md devices, they will not be destroyed until the array
is explicitly stopped, either with the STOP_ARRAY ioctl or by
writing 'clear' to /sys/block/md_XXXX/md/array_state.

The name of the array must start 'md_' to avoid conflict with
other devices.
Signed-off-by: NNeilBrown <neilb@suse.de>

Currently md devices, once created, never disappear until the module
is unloaded.  This is essentially because the gendisk holds a
reference to the mddev, and the mddev holds a reference to the
gendisk, this a circular reference.

If we drop the reference from mddev to gendisk, then we need to ensure
that the mddev is destroyed when the gendisk is destroyed.  However it
is not possible to hook into the gendisk destruction process to enable
this.

So we drop the reference from the gendisk to the mddev and destroy the
gendisk when the mddev gets destroyed.  However this has a
complication.
Between the call
   __blkdev_get->get_gendisk->kobj_lookup->md_probe
and the call
   __blkdev_get->md_open

there is no obvious way to hold a reference on the mddev any more, so
unless something is done, it will disappear and gendisk will be
destroyed prematurely.

Also, once we decide to destroy the mddev, there will be an unlockable
moment before the gendisk is unlinked (blk_unregister_region) during
which a new reference to the gendisk can be created.  We need to
ensure that this reference can not be used.  i.e. the ->open must
fail.

So:
 1/  in md_probe we set a flag in the mddev (hold_active) which
     indicates that the array should be treated as active, even
     though there are no references, and no appearance of activity.
     This is cleared by md_release when the device is closed if it
     is no longer needed.
     This ensures that the gendisk will survive between md_probe and
     md_open.

 2/  In md_open we check if the mddev we expect to open matches
     the gendisk that we did open.
     If there is a mismatch we return -ERESTARTSYS and modify
     __blkdev_get to retry from the top in that case.
     In the -ERESTARTSYS sys case we make sure to wait until
     the old gendisk (that we succeeded in opening) is really gone so
     we loop at most once.

Some udev configurations will always open an md device when it first
appears.   If we allow an md device that was just created by an open
to disappear on an immediate close, then this can race with such udev
configurations and result in an infinite loop the device being opened
and closed, then re-open due to the 'ADD' even from the first open,
and then close and so on.
So we make sure an md device, once created by an open, remains active
at least until some md 'ioctl' has been made on it.  This means that
all normal usage of md devices will allow them to disappear promptly
when not needed, but the worst that an incorrect usage will do it
cause an inactive md device to be left in existence (it can easily be
removed).

As an array can be stopped by writing to a sysfs attribute
  echo clear > /sys/block/mdXXX/md/array_state
we need to use scheduled work for deleting the gendisk and other
kobjects.  This allows us to wait for any pending gendisk deletion to
complete by simply calling flush_scheduled_work().
Signed-off-by: NNeilBrown <neilb@suse.de>

md_free is the .release handler for the md kobj_type.
So it makes sense to release all the objects referenced by
the mddev in there, rather than just prior to calling kobject_put
for what we think is the last time.
Signed-off-by: NNeilBrown <neilb@suse.de>

It is more balanced to just do simple initialisation in mddev_find,
which allocates and links a new md device, and leave all the
more sophisticated allocation to md_probe (which calls mddev_find).
md_probe already allocated the gendisk.  It should allocate the
queue too.
Signed-off-by: NNeilBrown <neilb@suse.de>