Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 05 1月, 2011 14 次提交
  3. 30 12月, 2010 1 次提交
  5. 24 12月, 2010 1 次提交
  7. 23 12月, 2010 2 次提交
  9. 22 12月, 2010 1 次提交
  11. 21 12月, 2010 1 次提交
  13. 18 12月, 2010 9 次提交
  15. 16 12月, 2010 6 次提交
  17. 15 12月, 2010 2 次提交
    • A
      ext4: fix typo which broke '..' detection in ext4_find_entry() · 6d5c3aa8
      由 Aaro Koskinen 提交于 
      There should be a check for the NUL character instead of '0'.

Fortunately the only thing that cares about this is NFS serving, which
is why we didn't notice this in the merge window testing.
Reported-by: NPhil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
      6d5c3aa8
    • T
      ext4: Turn off multiple page-io submission by default · 1449032b
      由 Theodore Ts'o 提交于 
      Jon Nelson has found a test case which causes postgresql to fail with
the error:

psql:t.sql:4: ERROR: invalid page header in block 38269 of relation base/16384/16581

Under memory pressure, it looks like part of a file can end up getting
replaced by zero's.  Until we can figure out the cause, we'll roll
back the change and use block_write_full_page() instead of
ext4_bio_write_page().  The new, more efficient writing function can
be used via the mount option mblk_io_submit, so we can test and fix
the new page I/O code.

To reproduce the problem, install postgres 8.4 or 9.0, and pin enough
memory such that the system just at the end of triggering writeback
before running the following sql script:

begin;
create temporary table foo as select x as a, ARRAY[x] as b FROM
generate_series(1, 10000000 ) AS x;
create index foo_a_idx on foo (a);
create index foo_b_idx on foo USING GIN (b);
rollback;

If the temporary table is created on a hard drive partition which is
encrypted using dm_crypt, then under memory pressure, approximately
30-40% of the time, pgsql will issue the above failure.

This patch should fix this problem, and the problem will come back if
the file system is mounted with the mblk_io_submit mount option.
Reported-by: NJon Nelson <jnelson@jamponi.net>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
      1449032b
  19. 14 12月, 2010 3 次提交
    • C
      Btrfs: prevent RAID level downgrades when space is low · 83a50de9
      由 Chris Mason 提交于 
      The extent allocator has code that allows us to fill
allocations from any available block group, even if it doesn't
match the raid level we've requested.

This was put in because adding a new drive to a filesystem
made with the default mkfs options actually upgrades the metadata from
single spindle dup to full RAID1.

But, the code also allows us to allocate from a raid0 chunk when we
really want a raid1 or raid10 chunk.  This can cause big trouble because
mkfs creates a small (4MB) raid0 chunk for data and metadata which then
goes unused for raid1/raid10 installs.

The allocator will happily wander in and allocate from that chunk when
things get tight, which is not correct.

The fix here is to make sure that we provide duplication when the
caller has asked for it.  It does all the dups to be any raid level,
which preserves the dup->raid1 upgrade abilities.
Signed-off-by: NChris Mason <chris.mason@oracle.com>
      83a50de9
    • C
      Btrfs: account for missing devices in RAID allocation profiles · cd02dca5
      由 Chris Mason 提交于 
      When we mount in RAID degraded mode without adding a new device to
replace the failed one, we can end up using the wrong RAID flags for
allocations.

This results in strange combinations of block groups (raid1 in a raid10
filesystem) and corruptions when we try to allocate blocks from single
spindle chunks on drives that are actually missing.

The first device has two small 4MB chunks in it that mkfs creates and
these are usually unused in a raid1 or raid10 setup.  But, in -o degraded,
the allocator will fall back to these because the mask of desired raid groups
isn't correct.

The fix here is to count the missing devices as we build up the list
of devices in the system.  This count is used when picking the
raid level to make sure we continue using the same levels that were
in place before we lost a drive.
Signed-off-by: NChris Mason <chris.mason@oracle.com>
      cd02dca5
    • C
      Btrfs: EIO when we fail to read tree roots · 68433b73
      由 Chris Mason 提交于 
      If we just get a plain IO error when we read tree roots, the code
wasn't properly sending that error up the chain.  This allowed mounts to
continue when they should failed, and allowed operations
on partially setup root structs.  The end result was usually oopsen
on spinlocks that hadn't been spun up correctly.
Signed-off-by: NChris Mason <chris.mason@oracle.com>
      68433b73