Fix several error paths in matchall:
 - Release reference to actions in case the hardware fails offloading
   (relevant to skip_sw only)
 - Fix error path in case tcf_exts initialization/validation fail

Fixes: bf3994d2 ("net/sched: introduce Match-all classifier")
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2017-01-03

This series contains updates to ixgbe and ixgbevf only.

Emil fixes ixgbe to use the NVM settings for FEC, so do not override the
settings.  Fixed the indirection table for x550, where newer devices can
support up to 64 RSS queues.  Extends the rtnl_lock() to protect the call
to netif_device_detach() and ixgbe_clear_interrupt_scheme() to avoid
against a double free WARN and/or a BUG in free_msi_irqs().  Fixed AER
error handling by making sure that the driver frees the IRQs in
ixgbe_io_error_detected() when responding to a PCIe AER error, and to
restore them when the interface recovers.

Tony updates the driver to report the driver version to the firmware using
the host interface command for x550 devices.  Fixed the PHY reset check
for x550em_ext_t PHY type.  Fixed bounds checking for x540 devices to
ensure the index is valid for the LED function.  Fixed the BaseT adapters
which support 100Mb capability and were not reporting the capability.

Ken Cox adds a missing check for the trusted bit before trying to set the
MACVLAN MAC address.

Yusuke Suzuki fixes an issue with 82599 and x540 devices where receive
timestamps were not working becase the bitwise operation for RX_HWSTAMP
falg was incorrect.

Don ensures that x553 KR/KX devices correctly advertise link speeds.
Adds the mailbox message to allow for VF promiscuous mode support.

Mark fixes two issues with EEPROM access, where the semaphore was not
being held until the entire response was read and the acquiring/releasing
of the semaphore is slow.  Cleaned up firmware version method and
functions which are no longer used.  Added new interfaces for firmware
commands to access some new PHYs.

v2: fixed tab indentation in patch 12 and mis-spelled words in patch 15
    based on feedback from Sergei Shtylyov and Rami Rosen.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch extends the xcast mailbox message to include support for
unicast promiscuous mode.  To allow a VF to enter this mode the PF
must be in promiscuous mode.

A later patch will add the support needed in the VF driver (ixgbevf)
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends the mailbox message to allow for VF promiscuous
mode support.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement support for devices that have firmware-controlled PHYs.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement new interface for firmware commands to access some PHYs.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware version method and functions are not used anywhere, so
remove them all.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are two problems with EEPROM access. One is that it needs to
hold the semaphore until the entire response is read or else the
response can be corrupted by other firmware accesses. The second
problem is that acquiring and releasing the semaphore is slow, so
it should be taken and released once when multiple EEPROM accesses
will be done.

Both of these issues can be solved by adding a new function,
ixgbe_hic_unlocked, to issue firmware commands that will assume
that the caller has acquired the needed semaphore.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch ensures that the advertised link speeds are configured
for X553 KR/KX backplane.  Without this patch the link remains at
1G when resuming from low power after being downshifted by LPLU.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Restore adapter->hw.hw_addr after handling an error, or a resume
operation to make sure we can access the registers.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rx timestamp does not work on 82599 and X540 because bitwise operation
of RX_HWTSTAMP flags is incorrect and ixgbe_ptp_rx_hwtstamp() is never
called. This patch fixes it to enable Rx timestamp on 82599 and X540.

Without this fix:
ptp4l[278.730]: selected /dev/ptp8 as PTP clock
ptp4l[278.733]: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l[278.733]: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l[278.834]: port 1: received SYNC without timestamp
ptp4l[278.835]: port 1: new foreign master 1c3947.fffe.60f9cc-1
ptp4l[279.834]: port 1: received SYNC without timestamp
ptp4l[280.834]: port 1: received SYNC without timestamp
ptp4l[281.834]: port 1: received SYNC without timestamp
ptp4l[282.834]: port 1: received SYNC without timestamp
ptp4l[282.835]: selected best master clock 1c3947.fffe.60f9cc
ptp4l[282.835]: port 1: LISTENING to UNCALIBRATED on RS_SLAVE
ptp4l[283.834]: port 1: received SYNC without timestamp

With this fix:
ptp4l[239.154]: selected /dev/ptp8 as PTP clock
ptp4l[239.157]: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l[239.157]: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l[240.989]: port 1: new foreign master 1c3947.fffe.60f9cc-1
ptp4l[244.989]: selected best master clock 1c3947.fffe.60f9cc
ptp4l[244.989]: port 1: LISTENING to UNCALIBRATED on RS_SLAVE
ptp4l[246.977]: master offset -899583339542096 s0 freq      +0 path delay     16222
ptp4l[247.977]: master offset -899583339617265 s1 freq  -75169 path delay     16177
ptp4l[248.977]: master offset       -130 s2 freq  -75299 path delay     16177
ptp4l[248.977]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[249.977]: master offset         -9 s2 freq  -75217 path delay     16177
ptp4l[250.977]: master offset         88 s2 freq  -75123 path delay     16132

Fixes: a9763f3c ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: NYusuke Suzuki <yus-suzuki@uf.jp.nec.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure that we free the IRQs in ixgbevf_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.

Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbevf_remove() after a failed recovery from
AER error because the interrupts were not freed.

Also moved the down and free functions into ixgbevf_close_suspend()
same as with ixgbe.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure that we free the IRQs in ixgbe_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.

Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbe_remove() after a failed recovery from
AER error because the interrupts were not freed.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are two methods for setting mac addresses in a Macvlan, that
differentiate themselves in the function macvlan_set_mac_Address.
If the macvlan mode is passthru, then we use the dev_set_mac_address
method, otherwise we use the dev_uc api via macvlan_sync_addresses.
The latter method (which would stem from using any non-passthru mode,
like bridge, or vepa), calls down into the driver in a path that terminates
in ixgbevf_set_uc_addr_vf, which sends a IXGBE_VF_SET_MACVLAN message,
which causes the pf to spawn the noted error message.  This occurs because
it appears that the guest is trying to delete the mac address of the macvlan
before adding another.

The other path in macvlan_set_mac_address uses dev_set_mac_address, which
calls into ixgbevf_set_mac which uses the IXGBE_VF_SET_MAC_ADDR to the
pf to set the macvlan mac address.

The discrepancy here is in the handlers.  The handler function for
IXGBE_VF_SET_MAC_ADDR (ixgbe_set_vf_mac_addr) has a check for
the vfinfo[].trusted bit to allow the operation if the vf is trusted.
In comparison, the IXGBE_VF_SET_MACVLAN message handler
(ixgbe_set_vf_macvlan_msg) has no such check of the trusted bit.
Signed-off-by: NKen Cox <jkc@redhat.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When an interface is part of a namespace it is possible that
ixgbevf_close() may be called while ixgbevf_suspend() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs()

To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and check for !netif_device_present()
to avoid entering close while in suspend.

Also added rtnl locks to ixgbevf_queue_reset_subtask().

CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When an interface is part of a namespace it is possible that
ixgbe_close() may be called while __ixgbe_shutdown() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs().

To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and ixgbe_clear_interrupt_scheme()
in __ixgbe_shutdown() and check for netif_device_present()
to avoid clearing the interrupts second time in ixgbe_close();

Also extend the rtnl lock in ixgbe_resume() to netif_device_attach().
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

BaseT adapters that are capable of supporting 100Mb are not reporting this
capability.  This patch corrects the reporting so that 100Mb is shown as
supported on those adapters.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A retry count of 10 is likely to run into problems on X550 devices that
have to detect and reset unresponsive CS4227 devices. So, reduce the I2C
retry count to 3 for X550 and above. This should avoid any possible
regressions in existing devices.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is an extension of commit 003287e0 ("ixgbevf: Correct parameter
sent to LED function"); add bounds checking to x540 functions to ensure the
index is valid.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The indirection table was reported incorrectly for X550 and newer
where we can support up to 64 RSS queues.

Reported-by Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The generic PHY reset check we had previously is not sufficient for the
ixgbe_phy_x550em_ext_t PHY type.  Check 1.CC02.0 instead - same as
ixgbe_init_ext_t_x550().
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some x550 devices require the driver version reported to its firmware; this
patch sends the driver version string to the firmware through the host
interface command for x550 devices.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

FEC is configured by the NVM and the driver should not be
overriding it.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jon Maloy says:

====================
tipc: improve interaction socket-link

We fix a very real starvation problem that may occur when a link
encounters send buffer congestion. At the same time we make the
interaction between the socket and link layer simpler and more
consistent.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The socket code currently handles link congestion by either blocking
and trying to send again when the congestion has abated, or just
returning to the user with -EAGAIN and let him re-try later.

This mechanism is prone to starvation, because the wakeup algorithm is
non-atomic. During the time the link issues a wakeup signal, until the
socket wakes up and re-attempts sending, other senders may have come
in between and occupied the free buffer space in the link. This in turn
may lead to a socket having to make many send attempts before it is
successful. In extremely loaded systems we have observed latency times
of several seconds before a low-priority socket is able to send out a
message.

In this commit, we simplify this mechanism and reduce the risk of the
described scenario happening. When a message is attempted sent via a
congested link, we now let it be added to the link's backlog queue
anyway, thus permitting an oversubscription of one message per source
socket. We still create a wakeup item and return an error code, hence
instructing the sender to block or stop sending. Only when enough space
has been freed up in the link's backlog queue do we issue a wakeup event
that allows the sender to continue with the next message, if any.

The fact that a socket now can consider a message sent even when the
link returns a congestion code means that the sending socket code can
be simplified. Also, since this is a good opportunity to get rid of the
obsolete 'mtu change' condition in the three socket send functions, we
now choose to refactor those functions completely.
Signed-off-by: NParthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During multicast reception we currently use a simple linked list with
push/pop semantics to store port numbers.

We now see a need for a more generic list for storing values of type
u32. We therefore make some modifications to this list, while replacing
the prefix 'tipc_plist_' with 'u32_'. We also add a couple of new
functions which will come to use in the next commits.
Acked-by: NParthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions tipc_wait_for_sndpkt() and tipc_wait_for_sndmsg() are very
similar. The latter function is also called from two locations, and
there will be more in the coming commits, which will all need to test on
different conditions.

Instead of making yet another duplicates of the function, we now
introduce a new macro tipc_wait_for_cond() where the wakeup condition
can be stated as an argument to the call. This macro replaces all
current and future uses of the two functions, which can now be
eliminated.
Acked-by: NParthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
TPACKET_V3 TX_RING support

This patch series allows an application to use a single PF_PACKET
descriptor and leverage the best implementations of TX_RING
and RX_RING that exist today.

Patch 1 adds the kernel/Documentation changes for TX_RING
support and patch2 adds the associated test case in selftests.

Changes since v2: additional sanity checks for setsockopt
input for TX_RING/TPACKET_V3. Refactored psock_tpacket.c
test code to avoid code duplication from V2.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a test case and sample code for (TPACKET_V3, PACKET_TX_RING)
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although TPACKET_V3 Rx has some benefits over TPACKET_V2 Rx, *_v3
does not currently have TX_RING support. As a result an application
that wants the best perf for Tx and Rx (e.g. to handle request/response
transacations) ends up needing 2 sockets, one with *_v2 for Tx and
another with *_v3 for Rx.

This patch enables TPACKET_V2 compatible Tx features in TPACKET_V3
so that an application can use a single descriptor to get the benefits
of _v3 RX_RING and _v2 TX_RING. An application may do a block-send by
first filling up multiple frames in the Tx ring and then triggering a
transmit. This patch only support fixed size Tx frames for TPACKET_V3,
and requires that tp_next_offset must be zero.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While working with ipmr, we noticed that it is impossible to determine
if an entry is actually unresolved or its IIF interface has disappeared
(e.g. virtual interface got deleted). These entries look almost
identical to user-space when dumping or receiving notifications. So in
order to recognize them add a new RTNH_F_UNRESOLVED flag which is set when
sending an unresolved cache entry to user-space.
Suggested-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices, such as the mv88e6097 do have ADDR[0] external and so it
is possible to configure the device to use SMI address 0x1. Remove the
restriction, as there are boards using this address.
Signed-off-by: NVolodymyr Bendiuga <volodymyr.bendiuga@westermo.se>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for_4.11/net-next/rds_v3' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux

Santosh Shilimkar says:

====================
net: RDS updates

v2->v3:
- Re-based against latest net-next head.
- Dropped a user visible change after discussing with David Miller.
  It needs some more work to fully support old/new tools matrix.
- Addressed Dave's comment about bool usage in patch
  "RDS: IB: track and log active side..."

v1->v2:
Re-aligned indentation in patch 'RDS: mark few internal functions..."

Series consist of:
 - RDMA transport fixes for map failure, listen sequence, handler panic and
   composite message notification.
 - Couple of sparse fixes.
 - Message logging improvements for bind failure, use once mr semantics
   and connection remote address, active end point.
 - Performance improvement for RDMA transport by reducing the post send
   pressure on the queue and spreading the CQ vectors.
 - Useful statistics for socket send/recv usage and receive cache usage.
 - Additional RDS CMSG used by application to track the RDS message
   stages for certain type of traffic to find out latency spots.
   Can be enabled/disabled per socket.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Socket option to tap receive path latency in various stages
in nano seconds. It can be enabled on selective sockets using
using SO_RDS_MSG_RXPATH_LATENCY socket option. RDS will return
the data to application with RDS_CMSG_RXPATH_LATENCY in defined
format. Scope is left to add more trace points for future
without need of change in the interface.
Reviewed-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>

RDS support max message size as 1M but the code doesn't check this
in all cases. Patch fixes it for RDMA & non-RDMA and RDS MR size
and its enforced irrespective of underlying transport.
Signed-off-by: NAvinash Repaka <avinash.repaka@oracle.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>

Tracks the receive side memory added to scokets and removed from sockets.
Signed-off-by: NVenkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>

Shutdown code reaping loop takes care of emptying the
CQ's before they being destroyed. And once tasklets are
killed, the hanlders are not expected to run.

But because of core tasklet code issues, tasklet handler could
still run even after tasklet_kill,
RDS IB shutdown code already reaps the CQs before freeing
cq/qp resources so as such the handlers have nothing left
to do post shutdown.

On other hand any handler running after teardown and trying
to access already freed qp/cq resources causes issues
Patch fixes this race by  makes sure that handlers returns
without any action post teardown.
Reviewed-by: NWengang <wen.gang.wang@oracle.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>