Low EMI (Electro-Magnetic Interference) mode means lower slew
rate on the signals. The Nomadik GPIO controller supports
this so create an interface to enable it.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Pass the base offset to the Nomadik MTU timer in the init call
instead of keeping a global pointer to be assigned.
Acked-by: NAlessandro Rubini <rubini@unipv.it>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Allow logical channels to specify the physical channel they want to use.
This is needed to avoid two peripherals operating on the same physical
channel during some special use-cases. (like mmc and usb during a
usb mass storage case).
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NNarayanan G <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

This patch provides an option of having the lcla (link address)
in ESRAM instead of allocating it. The bool value (use_esram_lcla)
in the stedma40_platform_data if set to true, then the lcla
address would be taken from platform resources. Also, the
corresponding esram regulator is managed in the
suspend/resume functions.
Signed-off-by: NNarayanan G <narayanan.gopalakrishnan@stericsson.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves dma/drivers/* to use new enum

Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Zhang Wei <zw@zh-kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Yong Wang <yong.y.wang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Cc: Boojin Kim <boojin.kim@samsung.com>
Cc: Barry Song <Baohua.Song@csr.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

We make the reset function from the driver public, then
we also move of all register defines from the public header
file into driver, where they belong.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The GPIO clock is required for register access and interrupt detection.
When interrupt detection is not required on any of the pin in a block,
the block's clock can be disabled when the registers are not being
accessed.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
[Adjust for new IRQ chip core code, use only local functions]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Remove PIN_CFG_PULL in pincfg.h for plat-nomadik, PIN_CFG_INPUT
already takes care of this. Added support for SPI2.
Signed-off-by: NFredrik Svensson <fredrik.xk.svensson@stericsson.com>
Signed-off-by: NDaniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

After recent consolidations the Nomadik <plat/gpio.h> is entirely
superfluous, so get rid of it.
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.

Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead.  This means that by default, you get the trivial implementation
and only have to do something extra if you need to.  This should
encourage the use of the trivial default implementation.

As an additional bonus, several gpio.h header files become empty.
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Many of the gpio_to_irq implementations use the gpiolib version of this
function.  Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish.  Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Consolidate 24 trivial gpiolib implementions out of mach/gpio.h
into asm/gpio.h.  This is basically the include of asm-generic/gpio.h
and the definition of gpio_get_value, gpio_set_value, and gpio_cansleep
as described in Documentation/gpio.txt
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: NDavid Brown <davidb@codeaurora.org>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).

To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.

Hope people are OK with tiny include file.

Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: NAxel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NMartin Persson <martin.persson@stericsson.com>
[Split off from larger patch]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The I2C speed enumerators in the i2c-nomadik header file were in
the wrong order.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add option to have different i2c timeout delay for different i2c buses
specified in platform data. Default to the old value unless specified.
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Enable wakeups by default for any GPIO interrupts and in the suspend/resume
path narrow this down to only the the real wakeup interrupts. This approach is
based on the assumption that cpuidle ApSleep will be entered more often than
system suspend.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixup for genirq changes to struct irq_data on 2.6.38]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Setting pinmux alternative C for a GPIO pin is actually not
so easy since it ivolves setting value "1" in two registers,
and since the combined result will take effect for intermediate
values (01 or 10) this will cause glitches while you wrote one
register but have not yet written the other.

This patch implements a series of kludges including an optional
machine-specific callback to avoid glitches when changing pin
mux mode to alternative C.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When GPIOs wake up the system from sleep mode, the normal GPIO interrupt
handler does not hit and the normal interrupt status register does not
contain the status. Instead the secondary GPIO handler does, and the
interrupt status needs to be retrieved from the wakeup status saved by
the suspend/resume code.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
[Added constant 32-pin assignment in platform data]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The dmaengine framework has the API for this now.
Acked-by: NPer Forlin <per.forlin@stericsson.com>
Acked-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

DB8500v2's DMA40 (revision 3) allows setting event lines as high priority and
real time.
Acked-by: NPer Forlin <per.forlin@stericsson.com>
Acked-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The maximum transfer size of the stedma40 is (64k-1) x data-width.
If the transfer size of one element exceeds this limit
the job is split up and sent as linked transfer.
Signed-off-by: NPer Forlin <per.forlin@linaro.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

In the nomadik GPIO pin configuration, allow the sleep mode direction
and pull configurations to differ from the ones for the normal state.
PIN_SLPM_PULL_*, PIN_SLPM_INPUT, PIN_SLPM_OUTPUT* macros are provided
for this.

Since the hardware does not allow seperate configurations for sleep mode
and normal mode, this is implemented by having software remux the
configurations as necessary.
Reviewed-by: NSrinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

Signed-off-by: NZimny Lech <napohybelskurwysynom2010@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It has been replaced with separate fields.
Acked-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

A bool will suffice.  The default is little endian.
Acked-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

This does not seem to be implemented.
Acked-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Defaults are "basic mode" for physical channels, and "logical source
logical destination" for logical channels.
Acked-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

And keep it logical by default.
Acked-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

And keep it low priority by default.
Acked-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Add support for the keypad controller in the Scroll Key Encoder (SKE)
module on the Nomadik family and the DB8500 SoC.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

All platform data has to be made conditional on CONFIG_STEDMA40
or we can provide a simple dummy filter functions as to avoid
cluttering the code with other #ifdef:s.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Remove obsolete pre_transfer hook in stedma40_chan_cfg. The
intent of this hook is merely to handle burst size
compensation for ux500 variant MMCI. Remove obsolete stedma40_set_psize
since it is only called from pre_transfer. DMAEngine device_control
replaces the functionality of stedma40_set_psize.
Signed-off-by: NPer Forlin <per.forlin@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The half-channel struct was undocumented.
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The reqrite of the LCLA code rendered this variable unused.
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

This patch includes non functional code clean up changes,
file header updates and a few magic numbers got defined.
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>