Bits [18:16] of GEN6_GT_THREAD_STATUS_REG have always had the same
meaning since SNB. So treating them as something special for HSW doesn't
make sense to me.

Also the bits *seem* to work exactly the same way on IVB, HSW GT2 and
HSW GT3. At least intel_reg_read gives the identical results on all
platforms with and without forcewake.

Also the HSW PM guide rev 0.99 (ww05 2013) doesn't say anything about
those bits. It just says to poll for bits [2:0]. As does the more recent
BDW PM guide.

So just drop the HSW special case and treat all platforms the same way.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When reading out a DDI config that uses a PLL that is not part of the
shared_dpll scheme (DPLL0), it's totally normal to end up in the
default: case of that switch.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to "Cherryview_GFXclocks_y14w36d1.xlsx" the GPU frequency
divider should be 10 in when the CZ clock is 400 MHz. Change the code
to agree so that we report the correct frequencies.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The divider used in the GPU frequency calculations is compatible between
vlv and chv. vlv just wants doubled values compared to chv.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Always print the final PCBR register value on both vlv and chv, and
also tell us whether the BIOS was a good citizen or not.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Our freq<->opcode conversions assume that GPLL is always used.
Apparently that should be the case always, but let's scream if we
ever encounter something different.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Even with the rps debug messages signficantly recuced  by
 commit 67956867
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Tue Sep 2 15:12:17 2014 +0300

    drm/i915: Don't spam dmesg with rps messages on vlv/chv

we still get an inordinate amount of spam from this. Just kill the debug
print. If someone wants to observe it they can just use the tracepoint.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On chv the pipe-a power well is the new disp2d well, and it kills pretty
much everything in the display block. So we need to do the the same
dance that vlv does wrt. display irqs and hpd when the power well goes
up or down.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Replace the misinformed notes about CHV snoop behaviour with something
that's hopefully closer to reality.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Throw away the hand rolled display irq setup code on chv, and instead
just call vlv_display_irq_postinstall() and vlv_display_irq_uninstall().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pull the vlv display irq uninstall code into a separate function, for
eventual sharing with chv.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Running the driver without execlists and hence PPGTT (either aliasing or
full) isn't a supported configuration on gen9+.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_ddi.c:955:41: sparse: constant 8400000000 is so big it is long
intel_ddi.c:955:53: sparse: constant 9000000000 is so big it is long
intel_ddi.c:955:65: sparse: constant 9600000000 is so big it is long
intel_ddi.c:1028:23: sparse: constant 9600000000 is so big it is long
intel_ddi.c:1031:23: sparse: constant 9000000000 is so big it is long
intel_ddi.c:1034:23: sparse: constant 8400000000 is so big it is long
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Given the history, there's some chance we'll keep the same WM code for a
bit (previously, we were able to reuse the same WM code from ILK to BDW,
so that sounds like a fair assumption).
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Write and reads following the block changed use engine specific use counters
and unless that is matched here force wake use counting goes bad. Same
force wake is attempted to be taken twice which leads to at least time outs.

NOTE: Depending on feedback from hardware designers it may not be necessary
to grab force wakes on Gen9 here. But for Gen8 it is needed due to a race
between RC6 and ELSP writes.

v2: Added blitter force wake engine and made more future proof.
    Added commit note.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ville found out that the DATA1 register exists since SNB with some
scarce apparitions in the specs throughout the times. In his own words:

  Also according to Bspec the mailbox data1 register already existed
  since snb.  The hsw cdclk change sequence also mentions that it should
  be set to 0, but eg. the bdw IPS sequence doesn't mention it. I guess
  in theory some pcode command might cause it to be clobbered, so I'm
  thinking we should just explicitly set it to 0 for all platforms in
  the pcode read/write functions
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The LRC increased in size on gen9. Make sure we return the right
size in get_lr_context_size()

v2. Corrected the size, should be 22 pages. I unintentionally mailed out
a test patch w/ size equaling 23 pages.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NMichael H. Nguyen <michael.h.nguyen@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use the new AUX port irq bits where needed.

v2: Rebase on top of upstream changes
v3: Rebase on top of Oscar change to write IIR as soon as possible (Damien)
v4: Rebase on top of the for_each_pipe() change adding dev_priv as first
    argument (Damien)
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This moved around on SKL, so we need to make sure we read/write the
correct regs.

v2: fixup WIN_POS offsets (Paulo)
    zero out WIN_POS reg at disable time (Paulo)
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuougseek.org>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A few bits have changed in MI_DISPLAY_FLIP to accomodate the new planes.
DE_RRMR seems to have kept its plane flip bits backward compatible.

v2: Rebase on top of nightly
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Remove code that is now part of intel_crtc_page_flip()
    Don't use BUG() in default:
    Use intel_crtc->unpin_work->gtt_offset
    (Paulo)
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The eDP WA to stop link train based on port type is for HSW/BDW, not
required for SKL+.
Suggested by Satheesh

v2: Simplified the check befoe stop_link_train. Suggested by Satheesh.

v3: stop_link_train need not be called from intel_enable_ddi for gen >= 9
Suggested-by: NSatheeshakrishna M <satheeshakrishna.m@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NSatheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Cc: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: rebase on top of the hw state flattening.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch implements SKL DPLL programming that includes:
        - DPLL allocation
        - wide range PLL calculation and programming
        - DP link rate programming
        - DDI to DPLL mapping

v2: Incorporated following changes
        - Added vfunc for function required outside
        - Fixed multiple comments in WRPLL calculation

v3: - Fix the DCO computation
    - Move the initialization up to not clobber the computed values
    - Use the correct macro for DP link rate programming.
    - Use wait_for() to wait for the PLL locked bit

v4: Rebase on top of nigthly (Damien)

v5: A few code cleanups in the WRPLL computation (Damien)
    - Use uint32_t when possible
    - Use abs_diff() in the WRPLL computation
    - Make the 64bits divisions use div64_u64()
    - Fix typo in dco_central_feq_deviation (freq)
    - Replace the chain of breaks with a goto

v6: Port of the patch to work on top of the shared DPLLs (Damien)
v7: Don't try to handle eDP in ddi_pll_select() (Damien)
v8: Modified as per review comments from Paulo (Satheesh)
v9: Rebase on top of Ander's clock computation staging work for atomic (Damien)
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Skylake deprecates the usage of PORT_CLK_SEL and we are advised to use
the new DPLL_CRTL2 for the DDI->PLL mapping.

v2: Modified as per review comments
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NSatheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On skylake, DPLL 1, 2 and 3 can be used for DP and HDMI. The shared dpll
framework allows us to share those DPLLs among DDIs when possible.

The most tricky part is to provide a DPLL state that can be easily
compared. DPLL_CRTL1 is shared by all the DPLLs, 6 bits each. The
per-dpll crtl1 field of the hw state is then normalized to be the same
value if 2 DPLLs do indeed have identical values for those 6 bits.

v2: Port the code to the shared DPLL infrastructure (Damien)

v3: Rebase on top of Ander's clock computation staging work for atomic (Damien)

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v2)
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Modify the implementation to query DPLL attached to a SKL port.

v2: Rebase on top of the run-time PM on DPMS series (Damien)

v3: Modified as per review comments from Paulo
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NSatheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Fixup compilation due to the removal of the intel_ddi_dpll_id enum.
And add a fixme about the abuse of pipe_config here.

v3: Rebase on top of the hsw_ddi_clock_get() rename (Damien)

v4: Modified as per review comments from Paulo
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Determine programmed cd clock for SKL.

v2: Fix the LCPLL1 enable warning logic

v3: Rebase over the hsw pll rework.

v4: Rebase on top of the per-platform split (Damien)

v5: Modified as per review comments from Paulo
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NSatheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Adding structure/enum for SKL clocking implementation.

v2: Addressed Damien's comment
	- Removed internal structure from this header file

v3: Stove this into the generic intel_dpll_id enum and give them the established
DPLL_ID_ prefixes. (Daniel)

v4: - We'll only try to share DPLL1/2/3, leaving DPLL0 to eDP
    - Use SKL in the skylake shared DPLL names
    - Re-add the skl_dpll enum
    (Damien)

v5: Remove SKL_DPLL_NONE (Daniel)

v6: Modified as per review comments from Paulo
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v4,v5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v3)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch defines the necessary SKL registers for implementing the
new clocking mechanism.

v2: Addressed review comments by Damien
	- Added code comment
	- Introduced enum for WRPLL values

v3: Rebase on top of nightly (minor conflict in i915_reg.h)

v4: Use 0x, not 0X (Ville)

v5: Modified as per review comments from Paulo
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3,v4)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some machines may have a broken VBT or no VBT at all, but we still want
to use SSC there.  So check for it and keep it enabled if we see it
already on.  Based on an earlier fix from Kristian.

v2: honor modparam if set too (Daniel)
    read out at init time and store for panel_use_ssc() use (Jesse)
v3: trust BIOS configuration over VBT like we do for DP (Jani)
Reported-by: NKristian Høgsberg <hoegsberg@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This has been invalidated in

commit 24f3a8cf
Author: Akash Goel <akash.goel@intel.com>
Date:   Tue Jun 17 10:59:42 2014 +0530

    drm/i915: Added write-enable pte bit supportt

But despite that it's in the diff context no one noticed :(

Cc: Akash Goel <akash.goel@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Use the same conditions, group by features, add comments.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is not used within the driver, and merely saving/restoring these
registers isn't going to do any good anyway. In fact, it's possible it's
actively harmful. Any code enabling the feature should handle this
completely in the regular platform specific enable/disable backlight
functions.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

AFAICT i9xx_pfit_disable() on the GMCH display crtc disable path in
i9xx_crtc_disable() will always disable the panel fitter by writing 0 to
PFIT_CONTROL. The register save will always save/restore 0. Also we
completely recompue both in intel_gmch_panel_fitting so there's no way
we depend upon leftover bits.

Move the PFIT_CONTROL and PFIT_PGM_RATIOS save/restore to UMS
code. While at it, save/restore them both under the same conditions.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Make it a bit clearer that we nowhere depend upon these
bits.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The block was added for spin_lock_irqsave flags, but since the locking
was converted to spin_lock_irq variant, the block is no longer needed.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since RSTDBYCTL is only saved on non-KMS path in within i915_save_state,
move the restore in i915_restore_state for symmetry.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Don't save the panel power sequencer register on vlv/chv for two simple
reasons. First, these are the wrong registers to save to begin
with. Second, they are not restored anyway.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>