Encapsulate part of ata_scsi_queuecmd so that it can be
reused by future SAS patches.
Signed-off-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Mostly, trim trailing whitespace.

Also:
* export ata_dev_pair
* move ata_dev_classify export closer to ata_dev_pair export

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

At the moment libata doesn't pass pm_message_t down ata_device_suspend.
This causes drives to be powered down when we just want a freeze,
causing unnecessary wear and tear. This patch gets pm_message_t passed
down so that it can be used to determine whether to power down the
drive.
Signed-off-by: NNigel Cunningham <nigel@suspend2.net>

 drivers/scsi/libata-core.c |    5 +++--
 drivers/scsi/libata-scsi.c |    4 ++--
 drivers/scsi/scsi_sysfs.c  |    2 +-
 include/linux/libata.h     |    4 ++--
 include/scsi/scsi_host.h   |    2 +-
 5 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_set_mode() responsible for determining whether to take port
or device offline on failure.  ata_dev_set_xfermode() and
ata_dev_set_mode() indicate error to the caller instead of disabling
port directly on failure.  Also, for consistency, ata_dev_present()
check is done in ata_set_mode() instead of ata_dev_set_mode().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We may or may not disable a device after ata_dev_configure() fails.
Kill 'not supported, ignoring' message in ata_dev_configure() and use
ata_dev_disable() in ata_bus_probe().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch implements ata_dev_disable() which prints a warning message
and takes @dev offline.  Currently, this is done by explicitly
incrementing dev->class with case-by-case warning messages.  Giving
user clear indication when libata gives up will be more important as
libata will be doing more retries.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

libata core is being changed to disallow port/device disable on lower
layers.  However, some LLDDs (sata_mv) directly disable port on
command failure.  This patch makes ata_exec_internal() check whether a
port got disabled after an internal command.  If it is, AC_ERR_SYSTEM
is added to err_mask and the port gets re-enabled.

As internal command failure results in device disable for drivers
which don't implement newer reset/EH callbacks, this change results in
no behavior change for single device per port controllers.  For
slave-possible LLDDs which disable port on command failure, (1) such
drivers don't exist currently, (2) issuing command to the other device
of once-disabled port shouldn't result in catastrophe even if such
driver exists.  So, this should be enough as a temporary measure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Now that each ata_device has xfer masks, per-dev limits can be made
per-dev instead of per-port.  Make per-dev limits per-dev.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add per-dev pio/mwdma/udma_mask.  All transfer mode limits used to be
applied to ap->*_mask which unnecessarily restricted other devices
sharing the port.  This change will also benefit later EH speed down
and hotplug.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement ata_unpack_xfermask().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

No code changes, just moving code between files.

sata_uli was storing PCI config addresses in a variable intended for
port addresses, a variable soon to become void __iomem *.

Update the driver to store the SCR address, found in PCI config space,
in the driver-private data area.

eliminate a bunch of
	if (mmio)
		writel()
	else
		outl()

code with the pci_iomap() and io{read,write}{8,16,32}() interface.

* libata will soon move to iomap, so we should use
  pci_iomap() and pci_iounmap().
* Use kzalloc() where appropriate.

If the debug driver is built-in, link it in last, so that any real
drivers will probe first, rather than having the debug driver pick the
first scsi slots..
Signed-off-by: NDouglas Gilbert <dougg@torque.net>
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NJames Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Now that libata is smart enought to handle both soft and hard resets,
add softreset method.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As libata now can do PIO, don't ignore PIO-only devices.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sg increments the refcount of constituent pages in its higher order memory
allocations when they are about to be mapped by userspace.  This is done so
the subsequent get_page/put_page when doing the mapping and unmapping does not
free the page.

Move over to the preferred way, that is, using compound pages instead.  This
fixes a whole class of possible obscure bugs where a get_user_pages on a
constituent page may outlast the user mappings or even the driver.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure.  However, that is not what happens.  The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap().  Cache_reap()
is run every few seconds independently of memory pressure.

Could we remove the whole thing?  Its only used by three slabs anyways and
I cannot find a reason for having this option.

There is an additional problem with SLAB_NO_REAP.  If set then the recovery
of objects from alien caches is switched off.  Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk.  (Strangely __cache_shrink does not
check for SLAB_NO_REAP)

Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Also, bump sata_vsc version.

Also, cleanup interrupt mask content and note in Kconfig that this
driver supports the Intel 31244.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Alan noted: "bmdma may be zero but the bmdma_irq_clear function gets
called even in this case during pure PIO operation. Check we have a
bmdma before we use it."

I fixed this by adding a check for zero.  While was I there, I fixed the
non-standard indentation of the small function's code.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The first performs the simplex clearing relevant to some chipsets that
report simplex by default but can in fact do more if poked. The second
is used to strip DMA modes from a PCI control with no BAR4 allocation.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch addresses a number of weird behaviours observed
for the sata_mv driver, by fixing an "off by one" bug in processing
of the EDMA response queue.

Basically, sata_mv was looking in the wrong place for
command results, and this produced a lot of unpredictable behaviour.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Encapsulate some of ata_scsi_slave_config so that parts
can be reused in future SAS patches.
Signed-off-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add some dummy noop functions for use by libata clients
that do not need to do anything. Future SAS patches will
utilize these functions.
Signed-off-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove the ATA_PROT_PIO_MULT protocol.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add ata_port_flush_task() to ata_exec_internal().
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Original patch (and description) by Douglas Gilbert, with minor fixes
and API updates from me.

Changelog:
  - make existing libata VPD device identification page (0x83)
    supply the ATA serial number in the libata "vendor
    specific" designator (from Chris Paulson-Ellis)
  - add a "t10 vendor id based" designator as defined in
    SAT rev 08 (section 10.3.4.2.3) that supplies ATA
    model and serial numbers
  - make the libata VPD page 0x83 more extensible (for
    adding more designators in the future).
  - rename EVPD to VPD in various places. Enable Vital
    Product Data (EVPD) is a bit in the INQUIRY cdb.
Signed-off-by: NJeff Garzik <jeff@garzik.org>