In ixgbevf_get_ringparam we could run into a NULL pointer dereference
if the rings were not allocated when we attempted the call.  To prevent
that we can just access the tx/rx_ring_count values instead of attempting
to access the rings to get the count.

This change corrects a memory leak and memory corruption in
ixgbevf_set_ringparam.

The memory leak was due to us not freeing the resources from the ring
before overwriting them.  This change corrects the memory leak by making
certain to call ixgbe_free_tx/rx_resources on the rings prior to freeing
them.

The memory corruption was because we were replacing the rings but not
updating the q_vectors.  It addresses the memory corruption by leaving the
rings in place and instead just copying the contents of the new rings into
the existing rings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is a good bit of redundancy between the Tx checksum and segmentation
offloads.  In order to reduce some of this I am moving the code for
creating a context descriptor into a separate function.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds the netdev to the ring structure.  This allows for a
quicker transition from ring to netdev without having to go from ring to
adapter to netdev.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver is going back one step from its' previous location before
bumping tail. This is incorrect.  We should just be writing the value of
next_to_use into the tail register.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We have had an issue when using ixgbe+ixgbevf and 802.1 VLAN tagging.

When attaching a VLAN to a VF, frames with a 802.1q priority appeared
untagged on the VF hence not reaching the VLAN, where frames with
priority 0 where tagged as expected and seen by the VLAN device.

This seems due to the way ixgbevf is looking up the full tag
(prio+cfi+vlan) against the adapter active_vlans, as a condition to mark
the skb tagged.
Signed-off-by: NPascal Bouchareine <pascal@gandi.net>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Introduce ipv6_addr_hash() helper doing a XOR on all bits
of an IPv6 address, with an optimized x86_64 version.

Use it in flow dissector, as suggested by Andrew McGregor,
to reduce hash collision probabilities in fq_codel (and other
users of flow dissector)

Use it in ip6_tunnel.c and use more bit shuffling, as suggested
by David Laight, as existing hash was ignoring most of them.

Use it in sunrpc and use more bit shuffling, using hash_32().

Use it in net/ipv6/addrconf.c, using hash_32() as well.

As a cleanup, use it in net/ipv4/tcp_metrics.c
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NAndrew McGregor <andrewmcgr@gmail.com>
Cc: Dave Taht <dave.taht@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cloned patch of Eric Dumazet for bonding.

Some workloads greatly benefit of IFF_XMIT_DST_RELEASE capability
on output net device, avoiding dirtying dst refcount.

team currently disables IFF_XMIT_DST_RELEASE unconditionally.

If all ports have the IFF_XMIT_DST_RELEASE bit set, then
team dev can also have it in its priv_flags.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling runtime PM support for cpsw driver
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling runtime PM support for davinci mdio driver
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the netpoll function to support netconsole. Tested and works
fine on my "JMC250 PCI Express Gigabit Ethernet Controller" (PCI ID 0250).
Signed-off-by: NPeter Wu <lekensteyn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use correct allocation flags during copy of user space fragments
to the kernel. Also "improve" couple of for loops.
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add OF support for the davinci_emac driver.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: netdev@vger.kernel.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatoly Sivov <mm05@mail.ru>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usb_alloc_urb() return value needs to be checked to avoid
later NULL pointer access.
Reported by rucsoftsec@gmail.com via bugzilla.kernel.org #44601.
Signed-off-by: NKarsten Keil <kkeil@linux-pingi.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pnp_activate_dev() return value needs to be checked to make sure that
following calls calls to the PNP functions do work correctly.
Fix for report #44491 on bugzilla.kernel.org.
Signed-off-by: NKarsten Keil <kkeil@linux-pingi.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The condition is always true so WOL will never work.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers should pull only ethernet header from page frag
to skb->head.

Pulling 64 bytes is too much for TCP (without options) on IPv4.

However, it makes sense to pull all the frame if it fits the
128 bytes bloc allocated for skb->head, to free one page per
small incoming frame.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: NYan-Pai Chen <yanpai.chen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New VTI tunnel kernel module, Kconfig and Makefile changes.
Signed-off-by: NSaurabh Mohan <saurabh.mohan@vyatta.com>
Reviewed-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Incorporated David and Steffen's comments.
Add hook for rx-path xfmr4_mode_tunnel for VTI tunnel module.
Signed-off-by: NSaurabh Mohan <saurabh.mohan@vyatta.com>
Reviewed-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return -ENOTSUPP if the initialization fails because the
device is configured for a mode that is not supported by the driver.
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Followup of commit 0c24604b (tcp: implement RFC 5961 4.2)

As reported by Vijay Subramanian, we should send a challenge ACK
instead of a dup ack if a SYN flag is set on a packet received out of
window.

This permits the ratelimiting to work as intended, and to increase
correct SNMP counters.
Suggested-by: NVijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NVijay Subramanian <subramanian.vijay@gmail.com>
Cc: Kiran Kumar Kella <kkiran@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some workloads greatly benefit of IFF_XMIT_DST_RELEASE capability
on output net device, avoiding dirtying dst refcount.

bonding currently disables IFF_XMIT_DST_RELEASE unconditionally.

If all slaves have the IFF_XMIT_DST_RELEASE bit set, then
bonding master can also have it in its priv_flags
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usbnet API use the device ID table to store a pointer to
a minidriver. Setting a generic pointer for dynamic device
IDs will in most cases make them work as expected.  usbnet
will otherwise treat the dynamic IDs as blacklisted. That is
rarely useful.

There is no standard class describing devices supported by
this driver, and most vendors don't even provide enough
information to allow vendor specific wildcard matching. The
result is that most of the supported devices must be
explicitly listed in the device table.  Allowing dynamic IDs
to work both simplifies testing and verification of new
devices, and provides a way for end users to use a device
before the ID is added to the driver.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 64 bit stats to Broadcom b44 ethernet driver.
Signed-off-by: NKevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ability of driver to transmit packets depends on logical state
of the link. Ignore physical link status.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lancer FW has added new capability checks for VFs.
Driver should only use those capabilities which are allowed for VFs.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jerr Kirsher says:

====================
This series contains updates to ixgbe & ixgbevf.
 ...
Alexander Duyck (6):
  ixgbe: Ping the VFs on link status change to trigger link change
  ixgbe: Handle failures in the ixgbe_setup_rx/tx_resources calls
  ixgbe: Move configuration of set_real_num_rx/tx_queues into open
  ixgbe: Update the logic for ixgbe_cache_ring_dcb and DCB RSS
    configuration
  ixgbe: Cleanup logic for MRQC and MTQC configuration
  ixgbevf: Update descriptor macros to accept pointers and drop _ADV
    suffix
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Francois Romieu says:

====================
Francois Romieu (1):
      r8169: verbose error message.

Hayes Wang (1):
      r8169: remove rtl_ocpdr_cond.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
1. Fix potential badness when running a self-test with SR-IOV enabled.
2. Fix calculation of some interface statistics that could run backward.
3. Miscellaneous cleanup.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should provide to inet6_csk_route_socket a struct flowi6 pointer,
so that net6_csk_xmit() works correctly instead of sending garbage.

Also add some consts
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NYuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change updates the descriptor macros to accept pointers, updates the
name to drop the _ADV suffix, and include the IXGBEVF name in the macro.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to make the code much more readable for MTQC and MRQC
configuration.

The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
         DCB
         En       Dis
VMDq En  VMDQ/DCB VMDq/RSS
     Dis DCB/RSS  RSS

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.

In this patch I basically did 3 things.  I updated the logic for getting
the first register index.  I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register.  Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues.  By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls.  Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go.  This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.

This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

It is not needed for mac_ocp_{write / read}. Actually bit 31 of OCPDR
does not change and r8168_mac_ocp_read always returns ~0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Tested-by: NFrancois Romieu <romieu@fr.zoreil.com>

free_nh_exceptions() should use rcu_dereference_protected(..., 1)
since its called after one RCU grace period.

Also add some const-ification in recent code.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to mask it with (FNHE_HASH_SIZE - 1).
Signed-off-by: NDavid S. Miller <davem@davemloft.net>