On the imx51_3ds board, eCSPI2 is connected to a SPI NOR flash,
now add iomux definitions for those used pins.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Tested it by booting a rootfs via NFS.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:

- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds I2C functionality to the Freescale MX51 Babbage HW.
The patch adds device structures, i2c board slave device defines,
IOMUX pin defines, and clocks.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.

This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch is part of enabling USB for Freescale MX51 Babbage HW. This
patch updates the iomux pins for USB, and gpio line for reset the
USB hub on the MX51 Babbage HW.

This patch applies to 2.6.34-rc6.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add basic clock support, cpu identification, I/O mapping, interrupt
controller, serial port and ethernet.
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>