At the end of section 10.1 of AHCI spec (rev 1.3), it states

Software shall not set PxCMD.ST to 1 until it is determined that
a functoinal device is present on the port as determined by
PxTFD.STS.BSY=0, PxTFD.STS.DRQ=0 and PxSSTS.DET=3h

Even though most AHCI host controller works without this check,
specific controller will fail under this condition.
Signed-off-by: NJian Peng <jipeng2005@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The "struct ata_timing" must contain 10 members, but ".dmack_hold" member was
forgotten for "initial_timing" initialisation. This patch fixes such a problem.
Signed-off-by: NIgor Plyatov <plyatov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The AT91SAM9 microcontrollers with master clock higher then 105 MHz
and PIO0, have overflow of the NCS_RD_PULSE value in the MSB. This
lead to "NCS_RD_PULSE" pulse longer then "NRD_CYCLE" pulse and driver
does not detect ATA device.
Signed-off-by: NIgor Plyatov <plyatov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The previously submitted patch was word-wrapped.

This patch adds the AHCI-mode SATA DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The previously submitted patch was word-wrapped.

This patch adds the IDE-mode SATA DeviceIDs for the Intel Panther
Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

 Commit 4a5610a0 fixed an issue with
 the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user
 reported a similar issue with his DVR-216D that the NOSETXFER horkage
 worked around for him as well.

 This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER.

 The issue was reported at:
 https://bugzilla.novell.com/show_bug.cgi?id=679143Reported-by: NVolodymyr Kyrychenko <vladimir.kirichenko@gmail.com>
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.

Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Acked-by: NTejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

NVIDIA mcp65 familiy of controllers cause command timeouts when DIPM
is used.  Implement ATA_FLAG_NO_DIPM and apply it.

This problem was reported by Stefan Bader in the following thread.

 http://thread.gmane.org/gmane.linux.ide/48841

stable: applicable to 2.6.37 and 38.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NStefan Bader <stefan.bader@canonical.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds an sysfs attribute 'em_message_supported' to the
ahci host device which prints out the supported enclosure management
message types.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Use gpio_request_array() / gpio_free_array(), this makes the code
cleaner and less error prone.

This patch also properly frees GPIOs in case ata_host_activate() call fails.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

In FSL sata v2 block, the snoop bit of PRDT Word3 description
information is at bit28 instead of bit22.

This patch adds FSL sata v2 probe and resolve this difference.
Signed-off-by: NLei Xu <B33228@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1b4b:91a3 seems to be another PCI ID for marvell ahci.  Add it.
Reported and tested in the following thread.

 http://thread.gmane.org/gmane.linux.kernel/1068354Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NBorislav Petkov <bp@alien8.de>
Reported-by: NAlessandro Tagliapietra <tagliapietra.alessandro@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

RX_WATER_MARK sets the number of locations in Rx FIFO that can be used before
the transport layer instructs the link layer to transmit HOLDS. Note that it
can take some time for the HOLDs to get to the other end, and that in the
interim there must be enough room in the FIFO to absorb all data that could
arrive.

Update the new recommended value to 16.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When a single device error is detected, the device under the error
is indicated by the error bit set in the DER. There is a one to one
mapping between register bit and devices on Port multiplier(PMP)
i.e. bit 0 represents PMP device 0 and bit 1 represents PMP device
1 etc.

Current implementation treats Device error register value as device
number not set of bits representing multiple device on PMP. It is
changed to consider bit level.

No need to check for each set bit as all command is going to be
aborted.
Signed-off-by: NAshish Kalra <B00888@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

As per SAT-3 the WWN ID should be included in the VPD page 0x83
(device identification) emulation.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Some DMA controllers (eg: drivers/dma/dw_dmac*) allow platform specific
configuration for dma transfers. User drivers need to set chan->private field
of channel with pointer to configuration data. This patch takes dma_priv data
from platform data and passes it to chan->private_data, in order to pass
platform specific configuration to DMAC controller.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Commit 40d69ba0
("pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)")
used pr_<level>.

Add #define pr_fmt and remove DRV_NAME.
Increment driver version numbers.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The Arasan CompactFlash Device Controller has three basic modes of
operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card
ATA using true IDE modes.

Currently driver supports only True IDE mode.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds ata_sff_queue_work() & ata_sff_queue_delayed_work() routine in
libata-sff.c file. This routine can be used by ata drivers to use ata_sff_wq.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds an updated SATA RAID DeviceID for the Intel Patsburg PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Recognize Marvell 88SE9125 PCIe SATA 6.0 Gb/s controller.
Signed-off-by: NPer Jessen <per@computer.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 6b7ae954 (libata: reimplement link power
management) removed the check of ATA_FLAG_LPM but neglected to remove the flag
itself.  Do it now...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c306 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efd (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 0d5ff566 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

These flags are marked as obsolete and the checks for them have been removed
by commit 29444088 (libata-sff: kill unused
ata_bus_reset()), so I think it's time to finally get rid of them...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The driver makes use of the two options (CONFIG_SATA_DWC_[V]DEBUG) to enable
the debug output but they both are absent in drivers/ata/Kconfig...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The driver erroneously uses ata_get_cmd_descript() not only for printing out
the ATA commands but also the protocol and DMA direction enums. Add functions
for properly printing those out...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The caller expects this function to return the DMA channel number on success,
while it returns 0...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix the following compilation errors/warnings:

drivers/ata/sata_dwc_460ex.c:43:1: warning: "DRV_NAME" redefined
In file included from drivers/ata/sata_dwc_460ex.c:38:
drivers/ata/libata.h:31:1: warning: this is the location of the previous
definition
drivers/ata/sata_dwc_460ex.c:44:1: warning: "DRV_VERSION" redefined
drivers/ata/libata.h:32:1: warning: this is the location of the previous
definition
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_exec_command_by_tag':
drivers/ata/sata_dwc_460ex.c:1356: warning: passing argument 1 of
`ata_get_cmd_descript' makes integer from pointer without a cast
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue':
drivers/ata/sata_dwc_460ex.c:1476: warning: `err' is used uninitialized in this
function
drivers/ata/sata_dwc_460ex.c:1465: note: `err' was declared here
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue':
drivers/ata/sata_dwc_460ex.c:1493: warning: passing argument 1 of
`ata_get_cmd_descript' makes integer from pointer without a cast
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_prep':
drivers/ata/sata_dwc_460ex.c:1537: error: `tag' undeclared (first use in this
function)
drivers/ata/sata_dwc_460ex.c:1537: error: (Each undeclared identifier is
reported only once
drivers/ata/sata_dwc_460ex.c:1537: error: for each function it appears in.)

NB: error only happens if DEBUG_NCQ macro is defined...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Somehow the driver was committed with a bare number for the PIO mask, instead
of ATA_PIO4...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Right at the moment, the libata error handler is incredibly
monolithic.  This makes it impossible to use from composite drivers
like libsas and ipr which have to handle error themselves in the first
instance.

The essence of the change is to split the monolithic error handler
into two components: one which handles a queue of ata commands for
processing and the other which handles the back end of readying a
port.  This allows the upper error handler fine grained control in
calling libsas functions (and making sure they only get called for ATA
commands whose lower errors have been fixed up).
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The SCSI host eh_cmd_q should be protected by the host lock (not the
port lock).  This probably doesn't matter that much at the moment,
since we try to serialise the add and eh pieces, but it might matter
in future for more convenient error handling.  Plus this switches
libata to the standard eh pattern where you lock, remove from the cmd
queue to a local list and unlock and then operate on the local list.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For historical reasons, libsas uses the scsi host lock as the ata port
lock, and libata always uses the ata host.  For the old eh, this was
largely irrelevant since the two locks were never mixed inside the
code.  However, the new eh has a case where it nests acquisition of
the host lock inside the port lock (this does look rather deadlock
prone).  Obviously this would be an instant deadlock if the port lock
were the host lock, so switch the libsas paths to use the ata host
lock as well.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths.  This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ata_eh_analyze_serror() suppresses hotplug notifications if LPM is
being used because LPM generates spurious hotplug events.  It compared
whether link->lpm_policy was different from ATA_LPM_MAX_POWER to
determine whether LPM is enabled; however, this is incorrect as for
drivers which don't implement LPM, lpm_policy is always
ATA_LPM_UNKNOWN.  This disabled hotplug detection for all drivers
which don't implement LPM.

Fix it by comparing whether lpm_policy is greater than
ATA_LPM_MAX_POWER.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Final step to eliminate of_platform_bus_type.  They're all just
platform drivers now.

v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>