Loading cursors to the LCD controller's SRAM can be corrupted when the
configured pixel clock is relatively slow.  This seems to be caused
when we write back-to-back to the SRAM registers.

There doesn't appear to be any status register we can read to check
when an access has completed.

Inserting a dummy read between the writes appears to fix the problem.

Cc: <stable@vger.kernel.org> # 3.13
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If we get a msg.reply of REPLY_DEFER, we also get an err of 0
so we fail reads with 0 < size and return -EPROTO instead of trying
again.

v2: same fix in i2c code.

Found writing MST support.
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch exports ptn3460_init function so that other modules
can call this function.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

This patch removes MODULE_DEVICE_TABLE definition to of_device_id
of DP and MIPI-DSI drivers.

Eyxnos drm should be built as single module so these definitions
should be removed.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

The patch adds MIPI-DSI based S6E8AA0 AMOLED LCD panel driver.
Driver uses mipi_dsi bus to communicate with panel and exposes drm_panel
interface.

v2
- added bus error handling,
- set maxmimum DSI packet size on init,
- removed unsupported brightness drm_panel callbacks,
- minor improvements

v3
- switched to gpiod framework,
- minor fixes in error handling
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds LD9040 parallel RGB panel driver with SPI control interface.
The driver uses drm_panel framework.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds driver for Exynos DSI master (DSIM). It is a platform driver
which is registered as exynos_drm_display sub-driver of exynos_drm framework
and implements DRM encoder/connector pair.
It is also MIPI-DSI host driver and provides DSI bus for panels.
It interacts with its panel(s) using drm_panel framework.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds explicit check if there is a connector with
connected status before fbdev initialization. It prevents creation
of default fbdev 1024x768 which is unusable on panels with bigger resolutions.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

MIPI DSI host node can contain child nodes which are not DSI devices.
Checking for existence of reg property can be used to distinguish such nodes.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The Dell XPS 8700 has a onboard Display port and HDMI port and no VGA port.
The call intel_crt_init freeze the machine, so skip such call.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73559
Signed-off-by: Giacomo Comes <comes at naic.edu>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This typo may lead to missed RPS interrupts and as a result a too
low or too high frequency for the current workload. The interrupt mask
will be set properly at a subsequent GPU idle event, but can get
corrupted again at the next RPS up/down event.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As per the inputs provided by hardware team  we still use DDR
Rates as 0,1=800, 2=1066, 3=1333.
With this change, Turbo freqs used on current machines matches.

This reverts commit f64a28a7.

commit f64a28a7
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Mon Nov 4 16:07:00 2013 -0800

     drm/i915/vlv: fixup DDR freq detection per Punit spec

v2: Add reference to previous commit which changed this. (Daniel)
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

During resume the intel hda audio driver depends on the i915 driver
reinitializing the audio power domain. Since the order of calling the
i915 resume handler wrt. that of the audio driver is not guaranteed,
move the power domain reinitialization step to the resume_early
handler. This is guaranteed to run before the resume handler of any
other driver.

The power domain initialization in turn requires us to enable the i915
pci device first, so move that part earlier too.

Accordingly disabling of the i915 pci device should happen after the
audio suspend handler ran. So move the disabling later from the i915
resume handler to the resume_late handler.

v2:
- move intel_uncore_sanitize/early_sanitize earlier too, so they don't
  get reordered wrt. intel_power_domains_init_hw()

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76152Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable and loud comments that this is just a hack.]
[danvet: Fix "Should it be static?" sparse warning reported by Wu
Fengguang's kbuilder.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use the more canonical and concise variant of the GPL v2 license text.
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The majority of the code in this driver is licensed under the GPL v2, so
relicense the rest under GPL v2 as well for consistency.
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Tegra V4L2 camera driver needs this function to do frame capture.
Signed-off-by: NBryan Wu <pengw@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This is trivial to support since all GEM objects are mapped into kernel
space anyway.
Signed-off-by: NThierry Reding <treding@nvidia.com>

This panel is used by Tegra Note 7 and supported by the simple-panel
driver.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This panel is used by the NVIDIA SHIELD and supported by the
simple-panel driver.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

In order to differentiate between the different video modes (burst vs.
non-burst, sync pulses vs. sync events) supported by peripherals, pass
the flags that specify this mode in the panel description to the DSI
peripheral device when probed.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The enable GPIO for panels may be provided by GPIO expanders on slow
busses (such as I2C), and therefore toggling the GPIO may sleep. Since
these accesses don't happen in interrupt context, use the *_cansleep()
variants of the GPIO API.
Signed-off-by: NThierry Reding <treding@nvidia.com>

regulator_disable() is already performed by panel_simple_disable(),
which is called by panel_simple_remove().
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Use the new GPIO descriptor interface to handle the panel's enable GPIO.
This considerably simplifies the code.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
[treding@nvidia.com: rework to improve readability]
Signed-off-by: NThierry Reding <treding@nvidia.com>

The LP129QE LCD has an LED backlight and a display resolution of
2560x1700 pixels.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NBrian Paul <brianp@vmware.com>

Use the %pad printk specifier to print dma_addr_t variables. This fixes
warnings on platforms where dma_addr_t has a different size than int or
size_t.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The GEM CMA helpers uses a custom mmap implementation based on
remap_pfn_range(). While this works when the buffer DMA and physical
addresses are identical, it fails to take IOMMU into account and tries
to mmap the buffer to userspace using the DMA virtual address instead of
the physical address. This results in mapping random physical pages when
the device is behind an IOMMU.

Use the DMA mapping dma_mmap_writecombine() function instead.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

entry->size is the size of the node, not the size of the hole after it.
So the code would actually find the hole which can satisfy the
constraints and which is preceded by the smallest node, not the smallest
hole satisfying the constraints.
Reported-by: N"Huang, FrankR" <FrankR.Huang@amd.com>
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Currently drm_pick_cmdline_mode() doesn't care about the interlace
when the given mode line has no "i" suffix.  That is, when there are
multiple entries for the same resolution, an interlace mode might be
picked up just depending on the assigned order, and there is no way to
exclude it.

This patch changes the logic for the mode selection, to prefer the
noninterlace mode unless the interlace mode is explicitly given.
When no matching mode is found, it still tries the interlace mode as
fallback.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This decreases eviction by up to 20%, by improving the fragmentation
quality. No harm in normal cases that fit VRAM fully (PTS gaming suite).

In some cases, even the VRAM-fitting cases improved slightly (openarena, urban terror).

512kb was measured as the most optimal threshold for 3d workloads common to radeon.
Other drivers may need different thresholds according to their workloads.

v2: Nicer formatting
Signed-off-by: NLauri Kasanen <cand@gmx.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Clients like i915 need to segregate cache domains within the GTT which
can lead to small amounts of fragmentation. By allocating the uncached
buffers from the bottom and the cacheable buffers from the top, we can
reduce the amount of wasted space and also optimize allocation of the
mappable portion of the GTT to only those buffers that require CPU
access through the GTT.

For other drivers, allocating small bos from one end and large ones
from the other helps improve the quality of fragmentation.

Based on drm_mm work by Chris Wilson.

v3: Changed to use a TTM placement flag
v2: Updated kerneldoc

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Christian König <deathsimple@vodafone.de>
Signed-off-by: NLauri Kasanen <cand@gmx.com>
Signed-off-by: NDavid Airlie <airlied@redhat.com>

The rcar_du_encoder_init() function can fail and return an error code.
Don't ignore it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org

Need to swap on BE.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org

This needs to be done to update some of the fields in
the connector structure used by the audio code.

Noticed by several users on irc.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org

This completely reworks how the PLL parameters are generated and
should result in better matching dot clock frequencies.

Probably needs quite a bit of testing.

bugs: https://bugs.freedesktop.org/show_bug.cgi?id=76564

v2: more cleanup and comments.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

For runtime pm we'd never suspend with the modesetting hw turned on,
so don't try and resume the modesetting hw, as that path will take
locks that the interface that is causing us to wake up might also
take.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Same fix as for nouveau, when we fail with EINVAL, subsequent
gets fail hard, causing the device not to open.
Signed-off-by: NDave Airlie <airlied@redhat.com>

If the IB test fails we don't want to reset the card over
and over again, just accept that it isn't working.

Bug: https://bugs.freedesktop.org/show_bug.cgi?id=76501Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org