The HDMI modes needs more CMA memory to be reserved at boot-time.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Now that 3adbf342 "iio: adc: add a driver for the SAR ADC found in
Amlogic Meson SoCs" has added support for the ADC, let's enable it
on Odroid C2.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add EE and AO domains pins for the spdif output to the gxl device tree.
Acked-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add EE and AO domains pins for the i2s output clocks and data the gxl
device tree
Acked-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add EE and AO domains pins for the spdif output to the gxbb device tree.
Acked-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add EE and AO domains pins for the i2s output clocks and data to the gxbb
device tree.
Acked-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The ODroid-C2 on-board USB Hub needs to to have it's reset signal set to
high level in order to be enumerated by the USB Host Controller.

But this management must be part of the currently in-development Generic
Power Sequence patch that will allow a USB Controller driver to start and stop
a power sequence associated to the USB Bus.

In the meantime, a simple USB Hog will work to enable the USB Hub.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The same Mali-450 MP3 GPU is present in the GXBB and GXL SoCs.

The node is simply added in the meson-gxbb.dtsi file.

For GXL, since a lot is shared with the GXM that has a Mali-T820 IP, this
patch adds a new meson-gxl-mali.dtsi and is included in the SoC specific
dtsi files.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
[khilman: s/MALI/Mali in changelog]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add pinctrl pins nodes following the additions of missing pins in the pinctrl
driver.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Prepend the compatible strings with a GX generic name in nodes compatible with
the GXBB HW and keep the same scheme as other nodes.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Since we know the GXBB and GXL/GXM share more hardware, we can safely move
the remaining peripheral nodes present in the GXBB dtsi to the common GX dtsi.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The Khadas VIM series consists of two boards which are almost
identical:
They are both using the same GXL S905X SoC, 100Mbit/s ethernet
(through the SoC-internal PHY), 2GB DDR3 memory, a micro-SD card slot,
onboard eMMC, Broadcom based SDIO WIFI, 2x USB A and 1x USB Type-C (the
latter with OTG support). The red LED is driven by PWM_AO_B (which
allows dimming), while the blue LED is managed by the firmware.
The differences are:
- the VIM Pro has a 16GB eMMC module, while the VIM only has 8GB
- the VIM Pro uses an AP6255 a/b/g/n/ac WIFI module, while the VIM comes
  with an AP6212 b/g/n SDIO WIFI module
 (the Vim uses an 8GB eMMC module, while

The boards are based on Amlogic's GXL S905X P212 reference design, which
is why most of the functionality (all MMC controllers and power
sequences, IR remote input, the main UART, ADC and ethernet) is simply
inherited from meson-gxl-s905x-p212.dtsi.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Khadas is a new sub-brand of "Shenzhen Wesion Technology Co., Ltd.".
They are developing Amlogic and Rockchip based "DIY boxes" (single board
computers): http://khadas.com/
They are best know for their latest product: the Khadas VIM (an Amlogic
GXL S905X based SBC).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This adds the new DT nodes for the missing PWM pins in the EE and AO
domain.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The wrong GPIO line was provided here.

Fixes: ef8d2ffe ("ARM64: dts: meson-gxbb: add MMC support")
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This patch describes the GPIO lines usage on the Odroid-C2 board.

This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This patch adds support for the P230 and Q200 ADC laddered button and
GPIO button.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The Amlogic P212 reference design is used by other devices as well, such
as (for example) the Khadas VIM boards. Thus this patch adds and moves
all common entries from meson-gxl-s905x-p212.dts to a new, separate
meson-gxl-s905x-p212.dtsi (which can be re-used on boards such as the
Khadas VIM).
Support for all boards based on the P212 reference design includes:
- enabling IR support
- enabling the SAR ADC (SARADC_CH1 is connected to a resistor which
  indicates the hardware revision, a similar design is found on the
  Khadas VIM boards)
- all MMC controllers (which means that SDIO wifi, the SD card and the
  eMMC are now supported)
- pwm_ef as dependency for the SDIO wifi modules
- uart_A which is connected to the bluetooth module (the bluetooth
  module itself is not enabled yet due to missing devicetree bindings
  for the Broadcom serial bluetooth devices)
- uart_AO is moved to the .dtsi (as all known devices use it as their
  boot-console)

Specific to the P212 board:
- this also enables the CVBS connector (which is not available on the
  Khadas VIM boards for example)
- Realtek based SDIO wifi (instead of Broadcom which most other devices
  use)
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Tested-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This patch adds support for the HwaCom AmazeTV set-top-box. The
hardware configuration is really similar to the other GXL boards but
for this hardware we need to limit the max-frequency of the eMMC to
have it working.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Hwacom Systems Inc. is a broadband system integrator and supplier of
mobile, fixed and IP networks related services as well as
multimedia application. Website: http://www.hwacom.com/Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Acked-by: NRob Herring <robh@kernel.org>
[khilman: change shortlog prefix to dt-bindings]
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

The ethmac node has to be configured for each board due to different
pinctrl nodes for RGMII/RMII. Thus the phy-mode should be specified at
the same place (= in the board .dts), making it easier to read the board
.dts file (because the phy-mode is stated explicitly, without requiring
developers to read all "parent" .dtsi as well).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This adds the amlogic,tx-delay-ns property with the old (hardcoded)
default value of 2ns to all boards which are using an RGMII ethernet
PHY.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Amlogic's own .dts specifies that the P201 board uses a RMII PHY (with
the reset GPIO being GPIOZ_14).
However our P201 board .dts simply inherits the phy-mode setting from
from meson-gx.dtsi where it defaults to RGMII mode.
Remove all ethernet settings from meson-gxbb-p20x.dtsi as it only
specifies the RGMII pins which are only valid for the P200 board.
Instead we add the ethmac node to the meson-gxbb-p201.dts and configure
the pinctrl property and the phy-mode for an RMII PHY.

An MDIO node (which would also specify the PHY) is not added since we
don't know which PHY is being used (and thus which PHY address would
have to be used).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This resets the ethernet PHY during boot to get the PHY into a "clean"
state. While here also explicitly specify the phy-mode instead of
relying on the default-value from meson-gx.dtsi.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Pull networking fixes from David Miller:

 1) Fix double-free in batman-adv, from Sven Eckelmann.

 2) Fix packet stats for fast-RX path, from Joannes Berg.

 3) Netfilter's ip_route_me_harder() doesn't handle request sockets
    properly, fix from Florian Westphal.

 4) Fix sendmsg deadlock in rxrpc, from David Howells.

 5) Add missing RCU locking to transport hashtable scan, from Xin Long.

 6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.

 7) Fix race in NAPI handling between poll handlers and busy polling,
    from Eric Dumazet.

 8) TX path in vxlan and geneve need proper RCU locking, from Jakub
    Kicinski.

 9) SYN processing in DCCP and TCP need to disable BH, from Eric
    Dumazet.

10) Properly handle net_enable_timestamp() being invoked from IRQ
    context, also from Eric Dumazet.

11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.

12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
    Melo.

13) Fix use-after-free in netvsc driver, from Dexuan Cui.

14) Fix max MTU setting in bonding driver, from WANG Cong.

15) xen-netback hash table can be allocated from softirq context, so use
    GFP_ATOMIC. From Anoob Soman.

16) Fix MAC address change bug in bgmac driver, from Hari Vyas.

17) strparser needs to destroy strp_wq on module exit, from WANG Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  strparser: destroy workqueue on module exit
  sfc: fix IPID endianness in TSOv2
  sfc: avoid max() in array size
  rds: remove unnecessary returned value check
  rxrpc: Fix potential NULL-pointer exception
  nfp: correct DMA direction in XDP DMA sync
  nfp: don't tell FW about the reserved buffer space
  net: ethernet: bgmac: mac address change bug
  net: ethernet: bgmac: init sequence bug
  xen-netback: don't vfree() queues under spinlock
  xen-netback: keep a local pointer for vif in backend_disconnect()
  netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
  netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
  netfilter: nf_conntrack_sip: fix wrong memory initialisation
  can: flexcan: fix typo in comment
  can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
  can: gs_usb: fix coding style
  can: gs_usb: Don't use stack memory for USB transfers
  ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
  ixgbe: update the rss key on h/w, when ethtool ask for it
  ...

Pull more KVM updates from Radim Krčmář:
 "Second batch of KVM changes for the 4.11 merge window:

  PPC:
   - correct assumption about ASDR on POWER9
   - fix MMIO emulation on POWER9

  x86:
   - add a simple test for ioperm
   - cleanup TSS (going through KVM tree as the whole undertaking was
     caused by VMX's use of TSS)
   - fix nVMX interrupt delivery
   - fix some performance counters in the guest

  ... and two cleanup patches"

* tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Fix pending events injection
  x86/kvm/vmx: remove unused variable in segment_base()
  selftests/x86: Add a basic selftest for ioperm
  x86/asm: Tidy up TSS limit code
  kvm: convert kvm.users_count from atomic_t to refcount_t
  KVM: x86: never specify a sample period for virtualized in_tx_cp counters
  KVM: PPC: Book3S HV: Don't use ASDR for real-mode HPT faults on POWER9
  KVM: PPC: Book3S HV: Fix software walk of guest process page tables

Pull documentation fixes from Jonathan Corbet:
 "A few fixes for the docs tree, including one for a 4.11 build
  regression"

* tag 'docs-4.11-fixes' of git://git.lwn.net/linux:
  Documentation/sphinx: fix primary_domain configuration
  docs: Fix htmldocs build failure
  doc/ko_KR/memory-barriers: Update control-dependencies section
  pcieaer doc: update the link
  Documentation: Update path to sysrq.txt