This patch adds the driver for the built-in UART of the
Atheros AR933X SoCs.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: "Luis R.  Rodriguez" <rodrigue@qca.qualcomm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: linux-serial@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2526/Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Workaround dropped notifications in the iir register.  Prevent reads
coincident with new interrupt notifications by reading the iir at most
once per interrupt.
Reported-by: NNhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are some functions (uart_handle_dcd_change, _handle_cts_change,
_insert_char) which are big enough to not be inlined. So move them
from .h to .c. We need to export them so that modules can actually use
them.

They will be even bigger when we introduce tty refcounting to them.

While at it, cleanup the "Proud member of Uglyhacks'R'US". It means,
define uart_handle_sysrq_char only when SUPPORT_SYSRQ is set.
Otherwise define it as a macro. This is needed for some arm driver
where the second parameter is undefined if expanded.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The EFR (Enhenced-Features-Register) is located at a different offset
than the other devices supporting UART_CAP_EFR. This change add a special
setup quick to set UPF_EXAR_EFR on the port. UPF_EXAR_EFR is then used to
the port type to PORT_XR17D15X since it is for sure a XR17D15X uart.
Signed-off-by: NSøren Holm <sgh@sgh.dk>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that platforms can override the port IRQ handler and the only user
of these UPIO modes has been converted over, kill off UPIO_DWAPB and
UPIO_DWAPB32.
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some serial ports may have unusal requirements for interrupt handling
(e.g. the Synopsys DesignWare 8250-alike port and it's busy detect
interrupt).  Add a .handle_irq callback that can be used for platforms
to override the interrupt behaviour in a similar fashion to the
.serial_out and .serial_in callbacks.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

tty_wakeup can be called from any context. So there is no need to have
an extra tasklet for calling that. Hence save some space and remove
the tasklet completely.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Tegra's UART is currently auto-detected as PORT_XSCALE due to register
bit UART_IER.UUE being writable. However, the Tegra documentation states
that this register bit is reserved. Hence, we should not program it.

Instead, the documentation specifies that the UART is 16550 compatible.
However, Tegra does need register bit UART_IER.RTOIE set, which is not
enabled by any 16550 port type. This was not noticed before, since
PORT_XSCALE enables CAP_UUE, which conflates both UUE and RTOIE bit
programming.

This change defines PORT_TEGRA that doesn't set UART_CAP_UUE, but does
set UART_CAP_RTOIE, which is a new capability indicating that the RTOIE
bit needs to be enabled.
Based-on-code-by: NLaxman Dewangan <ldewangan@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Xilinx PS Uart is used on the new ARM based SoC. This
UART is not compatible with others such that a seperate
driver is required.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a helper function to gather timestamps.  This way clients don't have
to duplicate it.
Signed-off-by: NAlexander Gordeev <lasaine@lvk.cs.msu.su>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

To avoid unbalanced IRQ wake disable, ensure that wakeups are disabled
only when wakeups have been successfully enabled.
Tested on OMAP3630SDP/ZOOM3.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Reported-by: NPaul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some platforms contain a Synopsys DesignWare APB UART that is attached
to a 32-bit APB bus where sub-word accesses are not allowed. Add a new
IO type (UPIO_DWAPB32) that performs 32 bit acccesses to the UART.

v2:
	- don't test for 32 bit in the output fast path, provide a
	  separate dwabp32_serial_out() function. Refactor
	  dwabp_serial_out() so that we can reuse the LCR saving
	  code.
v3:
	- rebased on top of "8250: use container_of() instead of
	  casting"
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The printout for the type should be just "5xxx", so 512x users won't
wonder why they have a mpc52xx-type UART.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds a driver for the serial ports found in VIA and WonderMedia
Systems-on-Chip. Interrupt-driven FIFO operation is implemented.
The hardware also supports pure register-based operation (which is
slower) and DMA-based FIFO operation. As the FIFOs are only 16 bytes
long, DMA operation is probably not worth the hassle.
Signed-off-by: NAlexey Charkov <alchark@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a hook for platforms to specify custom pm methods.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Soon we will use that handy function in the altera_uart driver.
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds driver support for OMAP2/3/4 high speed UART.

The driver is made separate from 8250 driver as we cannot
over load 8250 driver with omap platform specific configuration for
features like DMA, it makes easier to implement features like DMA and
hardware flow control and software flow control configuration with
this driver as required for the omap-platform.
This patch involves only the core driver and its dependent.

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Bug seen by Dr. David Alan Gilbert with sparse
Signed-off-by: NPhilippe Langlais <philippe.langlais@stericsson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Sysrq operations do not accept tty argument anymore so no need to pass
it to us.

[Stephen Rothwell <sfr@canb.auug.org.au>: fix build breakage in drm code
 caused by sysrq using bool but not including linux/types.h]

[Sachin Sant <sachinp@in.ibm.com>: fix build breakage in s390 keyboadr
 driver]
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

UART Features extract from STEricsson U6715 data-sheet (arm926 SoC for mobile phone):
* Fully compatible with industry standard 16C550 and 16C450 from various
manufacturers
* RX and TX 64 byte FIFO reduces CPU interrupts
* Full double buffering
* Modem control signals include CTS, RTS, (and DSR, DTR on UART1 only)
* Automatic baud rate selection
* Manual or automatic RTS/CTS smart hardware flow control
* Programmable serial characteristics:
– Baud rate generation (50 to 3.25M baud)
– 5, 6, 7 or 8-bit characters
– Even, odd or no-parity bit generation and detection
– 1, 1.5 or 2 stop bit generation
* Independent control of transmit, receive, line status, data set interrupts and FIFOs
* Full status-reporting capabilities
* Separate DMA signaling for RX and TX
* Timed interrupt to spread receive interrupt on known duration
* DMA time-out interrupt to allow detection of end of reception
* Carkit pulse coding and decoding compliant with USB carkit control interface [40]

In 16550A auto-configuration, if the fifo size is 64 then it's an U6 16550A port
Add set_termios hook & export serial8250_do_set_termios to change uart
clock following baudrate
Signed-off-by: NPhilippe Langlais <philippe.langlais@stericsson.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a PCI & UART driver, which suppors both PIO and DMA mode
UART operation. It has 3 identical UART ports and one internal
DMA controller.

Current FW will export 4 pci devices for hsu: 3 uart ports and 1
dma controller, each has one IRQ line. And we need to discuss the
device model, one PCI device covering whole HSU should be a better
model, but there is a problem of how to export the 4 IRQs info

Current driver set the highest baud rate to 2746800bps, which is
easy to scale down to 115200/230400.... To suport higher baud rate,
we need add special process, change DLAB/DLH/PS/DIV/MUL registers
all together.

921600 is the highest baud rate that has been tested with Bluetooth
modem connected to HSU port 0. Will test more when there is right
BT firmware.

Current version contains several work around for A0's Silicon bugs
Signed-off-by: NFeng Tang <feng.tang@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

At the moment there is only one platform type supported and there is is
hard wired, but with these changes the infrastructure is now there for
anyone else to provide methods for their hardware.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Pass down the ldisc number so that the drivers don't have to peek into the
tty object themselves. This lets us get rid of another case of back referencing
port to tty which we don't want (because of races versus hangup/close).
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Such ports are found, e.g., on SH7372.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add an UART driver for the UART component available as a SOPC (System on
Programmable Chip) component for Altera FPGAs.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add an UART driver for the JTAG UART component available as a SOPC
(System on Programmable Chip) component for Altera FPGAs.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The design of the kdb shell requires that every device that can
provide input to kdb have a polling routine that exits immediately if
there is no character available.  This is required in order to get the
page scrolling mechanism working.

Changing the kernel debugger I/O API to require all polling character
routines to exit immediately if there is no data allows the kernel
debugger to process multiple input channels.

NO_POLL_CHAR will be the return code to the polling routine when ever
there is no character available.

CC: linux-serial@vger.kernel.org
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

Adds support, by using the PPS line discipline, for the PPS sources
connected with the CD (Carrier Detect) pin of a serial port.

[akpm@linux-foundation.org: fix cast size warnings]
Signed-off-by: NRodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds support for the APBUART serial port from Aeroflex
Gaisler's IP library GRLIB. It is currently used in all LEON3 designs
(SPARC V8) but can be used on other platforms as well (which support OF).
Signed-off-by: NKristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix new kernel-doc warnings in serial_core.[hc] files.

  Warning(include/linux/serial_core.h:485): No description found for parameter 'uport'
  Warning(include/linux/serial_core.h:485): Excess function parameter 'port' description in 'uart_handle_dcd_change'
  Warning(include/linux/serial_core.h:511): No description found for parameter 'uport'
  Warning(include/linux/serial_core.h:511): Excess function parameter 'port' description in 'uart_handle_cts_change'
  Warning(drivers/serial/serial_core.c:2437): No description found for parameter 'uport'
  Warning(drivers/serial/serial_core.c:2437): Excess function parameter 'port' description in 'uart_add_one_port'
  Warning(drivers/serial/serial_core.c:2509): No description found for parameter 'uport'
  Warning(drivers/serial/serial_core.c:2509): Excess function parameter 'port' description in 'uart_remove_one_port'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The serial layer for some reason uses different defines for the special
case close delays and then conditionally switches to/from the normal ones
in the ioctls.

Remove this rather pointless abstraction
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is used by various drivers not just serial and can be extracted
as commonality
Signed-off-by: NAlan Cox <alan@linux.intel.com>

They cover essentially the same stuff and we can therefore fold it into the
tty_port one.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This typedef is now extinct
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fortunately the serial layer was designed to use the same flag values but
with different names. It has its own SUSPENDED flag which is a free slot in
the ASYNC flags so we allocate it in the ASYNC flags instead.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove more stuff from the serial special case code
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove some more serial specific use
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We moved this into uart_state, now move the fields out of the separate
structure and kill it off.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is currently no provision for passing IRQ trigger flags for
serial IRQs with triggering requirements (such as GPIO IRQs)

This patch adds irqflags to plat_serial8250_port that can be passed
from board file to reqest_irq() of 8250 driver

Changes are backward compatible with boards passing UPF_SHARE_IRQ flag

Tested on Zoom2 board that has IRQF_TRIGGER_RISING requirement for 8250 irq

[Moved new flag to end to fix bugs in the original with the old_serial array
	-- Alan]
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>