Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 27 9月, 2011 1 次提交
  3. 24 8月, 2011 2 次提交
    • T
      ARM: OMAP: Introduce SoC specific early_init · 8f5b5a41
      由 Tony Lindgren 提交于 
      Introduce them for each omap variant and just make them all call
omap2_init_common_infrastructure for now. Do this for each board-*.c
file except for board-generic and board-omap3beagle as they use
the same machine ID for multiple SoCs.

No functional changes.
Signed-off-by: NTony Lindgren <tony@atomide.com>
      8f5b5a41
    • T
      ARM: OMAP: Move omap2_init_common_devices out of init_early · a4ca9dbe
      由 Tony Lindgren 提交于 
      There's no need to call omap2_init_common_devices from init_early.

It no longer does anything else except reprogram the memory timings
for some boards, so it's better to do it later so we have a chance
to get console messages if something goes wrong.

Move it to happen after omap_serial_init gets called. And while
patching it anyways, rename it to omap_sdrc_init as suggested by
Benoit Cousson <b-cousson@ti.com>.
Signed-off-by: NTony Lindgren <tony@atomide.com>
      a4ca9dbe
  5. 05 7月, 2011 5 次提交
  7. 04 7月, 2011 1 次提交
  9. 28 6月, 2011 1 次提交
  11. 20 6月, 2011 1 次提交
    • T
      omap: Set separate timer init functions to avoid cpu_is_omap tests · e74984e4
      由 Tony Lindgren 提交于 
      This is needed for the following patches so we can initialize the
rest of the hardware timers later on.

As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.

Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
      e74984e4
  13. 14 6月, 2011 1 次提交
  15. 01 6月, 2011 2 次提交
  17. 31 5月, 2011 1 次提交
  19. 12 5月, 2011 1 次提交
  21. 11 5月, 2011 2 次提交
  23. 03 5月, 2011 1 次提交
  25. 23 3月, 2011 1 次提交
  27. 16 3月, 2011 1 次提交
  29. 12 3月, 2011 1 次提交
  31. 08 3月, 2011 1 次提交
    • A
      arm: omap4: 4430sdp: drop ehci support · 09173b58
      由 Anand Gadiyar 提交于 
      Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.

Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).

Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.

So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      09173b58
  33. 02 3月, 2011 1 次提交
  35. 01 3月, 2011 2 次提交
  37. 26 2月, 2011 1 次提交
  39. 23 2月, 2011 1 次提交
    • B
      OMAP4: Fix -EINVAL for vana, vcxio, vdac · 530a5a50
      由 Balaji T K 提交于 
      Fixed regulators in twl6030 do not have set_voltage hook.
Regulator core returns -22 if set_voltage is NULL and apply_uV is set
while applying the constraint to set voltage resulting in failure during probe
of these regulators.
Do not set apply_uV for fixed regulators which don't have set_voltage.

machine_constraints_voltage: VANA: failed to apply 2100000uV constraint
twl_reg twl_reg.43: can't register VANA, -22
twl_reg: probe of twl_reg.43 failed with error -22
machine_constraints_voltage: VCXIO: failed to apply 1800000uV constraint
twl_reg twl_reg.44: can't register VCXIO, -22
twl_reg: probe of twl_reg.44 failed with error -22
machine_constraints_voltage: VDAC: failed to apply 1800000uV constraint
twl_reg twl_reg.45: can't register VDAC, -22
twl_reg: probe of twl_reg.45 failed with error -22
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      530a5a50
  41. 18 2月, 2011 2 次提交
  43. 17 2月, 2011 1 次提交
    • A
      arm: omap4: 4430sdp: drop ehci support · 1dbea0f5
      由 Anand Gadiyar 提交于 
      Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.

Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).

Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.

So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      1dbea0f5
  45. 15 2月, 2011 1 次提交
  47. 14 1月, 2011 1 次提交
    • T
      omap4: Fix ULPI PHY init for ES1.0 SDP · 7d4ca85a
      由 Tony Lindgren 提交于 
      Commit 6aa85a5a (omap4: 4430sdp:
enable the ehci port on 4430SDP) added code to enable EHCI
support on 4430sdp board.

Looks like the ULPI pin does not seem to be muxed properly on ES1.0
SDP and this causes the system to reboot when the ULPI PHY is
enabled.

Fix this by muxing the pin, this is the same setting for
both ES1.0 and ES2.0. Also add checking for gpio_request.

Cc: Keshava Munegowda <keshava_mgowda@ti.com
Signed-off-by: NTony Lindgren <tony@atomide.com>
      7d4ca85a
  49. 22 12月, 2010 1 次提交
    • P
      OMAP2+: io: split omap2_init_common_hw() · 4805734b
      由 Paul Walmsley 提交于 
      Split omap2_init_common_hw() into two functions.  The first,
omap2_init_common_infrastructure(), initializes the hwmod code and
data, the OMAP PM code, and the clock code and data.  The second,
omap2_init_common_devices(), handles any other early device
initialization that, for whatever reason, has not been or cannot be
moved to initcalls or early platform devices.

This patch is required for the hwmod postsetup patch, which allows
board files to change the state that hwmods should be placed into at
the conclusion of the hwmod _setup() function.  For example, for a
board whose creators wish to ensure watchdog coverage across the
entire kernel boot process, code to change the watchdog's postsetup
state will be added in the board-*.c file between the
omap2_init_common_infrastructure() and omap2_init_common_devices() function
calls.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
      4805734b
  51. 21 12月, 2010 2 次提交
  53. 10 12月, 2010 3 次提交
  55. 08 12月, 2010 1 次提交
    • V
      OMAP: GPIO: Implement GPIO as a platform device · 77640aab
      由 Varadarajan, Charulatha 提交于 
      Implement GPIO as a platform device.

GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.

omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.

Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.

Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.

Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.

Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).

Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.

Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.

In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs

TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
   instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
   to use runtime pm implentation.
Signed-off-by: NCharulatha V <charu@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Reviewed-by: NBasak, Partha <p-basak2@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: NTony Lindgren <tony@atomide.com>
      77640aab