On SNB the BIOS provided WM memory latency values seem insufficient to
handle high resolution displays.

In this particular case the display mode was a 2560x1440@60Hz, which
makes the pixel clock 241.5 MHz. It was empirically found that a memory
latency value if 1.2 usec is enough to avoid underruns, whereas the BIOS
provided value of 0.7 usec was clearly too low. Incidentally 1.2 usec
is what the typical BIOS provided values are on IVB systems.

Increase the WM memory latency values to at least 1.2 usec on SNB.
Hopefully this won't have a significant effect on power consumption.

v2: Increase the latency values regardless of the pixel clock

Cc: Robert N <crshman@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70254Tested-by: NRobert Navarro <crshman@gmail.com>
Tested-by: NVitaly Minko <vitaly.minko@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Apparently it doesn't work. X-tiled self-refresh works flawlessly
otoh. Apparently X still works correctly with linear framebuffers, so
might just be an issue with the initial modeset. It's unclear whether
this just borked wm setup from our side or a hw restriction, but just
disabling gets things going.

Note that this regression was only brought to light with

commit 3f2dc5ac
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date:   Fri Jan 10 14:06:47 2014 +0200

    drm/i915: Fix 915GM self-refresh enable/disable

before that self-refresh for i915GM didn't work at all.

Kudos to Ville for spotting a little bug in the original patch I've
attached to the bug.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76103Tested-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Cc: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
[Jani: rebase on top of drm-next with primary plane support.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

This typo may lead to missed RPS interrupts and as a result a too
low or too high frequency for the current workload. The interrupt mask
will be set properly at a subsequent GPU idle event, but can get
corrupted again at the next RPS up/down event.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As per the inputs provided by hardware team  we still use DDR
Rates as 0,1=800, 2=1066, 3=1333.
With this change, Turbo freqs used on current machines matches.

This reverts commit f64a28a7.

commit f64a28a7
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Mon Nov 4 16:07:00 2013 -0800

     drm/i915/vlv: fixup DDR freq detection per Punit spec

v2: Add reference to previous commit which changed this. (Daniel)
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC.  Replace all references to the CRTC fb with the
primary plane's fb.

This patch was generated by the Coccinelle semantic patching tool using
the following rules:

        @@ struct drm_crtc C; @@
        -   (C).fb
        +   C.primary->fb

        @@ struct drm_crtc *C; @@
        -   (C)->fb
        +   C->primary->fb

v3: Generate patch via coccinelle.  Actual removal of crtc->fb has been
    moved to a subsequent patch.

v2: Fixup several lingering crtc->fb instances that were missed in the
    first patch iteration.  [Rob Clark]
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>

Ensure that existing driver loops over all planes do not change behavior
when we begin adding new types of planes (primary and cursor) to the DRM
plane list in future patches.

v2: Switch to using drm_for_each_legacy_plane()

Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>

If runtime PM is enabled and we unset all modes, we will runtime
suspend after __intel_set_mode() , then function
intel_modeset_check_state() will try to read the HW state while it is
suspended and trigger lots of WARNs because it shouldn't be reading
registers.

So on this patch we make intel_ddi_connector_get_hw_state() return
false in case the power domain is disabled, and we also make
intel_display_power_enabled() return false in case the device is
suspended. Notice that we can't just use
intel_display_power_enabled_sw() because while the driver is being
initialized the power domain refcounts are not reflecting the real
state of the hardware.

Just for reference, I have previously published an alternate patch for
this problem, called "drm/i915: get runtime PM at intel_set_mode".

Testcase: igt/pm_pc8
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Atm we reserve/allocate and free the power context during GT power
enable/disable time. There is no need to do this, we can reserve/allocate
the buffer once during driver loading and free it during driver cleanup.
The re-reservation can also fail in case the driver previously manages to
allocate something on the given fixed address.

The buffer isn't exepected to move even if allocated by the BIOS, for
safety add an assert to check this assumption.

This also fixed a bug for Ville, where re-reserving the context failed
during a GPU reset (I assume because something else got allocated on its
fixed address).
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove the rest of the references to drm_i915_private_t. No functional
changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Drop hunk in i915_cmd_parser.c]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The speculation is that we can conserve more power by masking off
the interrupts at source (PMINTRMSK) rather than filtering them by the
up/down thresholds (RPINTLIM). We can select which events we know will
be active based on the current frequency versus our imposed range, i.e.
if at minimum, we know we will not want to generate any more
down-interrupts and vice versa.

v2: We only need the TIMEOUT when above min frequency.
v3: Tweak VLV at the same time
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

What used to be a short-circuit now needs to adjust interrupt masking in
response to user requests for changing the min/max allowed frequencies.
This is currently done by a special case and early return, but the next
patch adds another common action to take, so refactor the code to reduce
duplication.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This reverts commit 27544369.

Conflicts:
	drivers/gpu/drm/i915/i915_irq.c

The partial application of interrupt masking without regard to other
pathways for adjusting the RPS frequency results in completely disabling
the PM interrupts. This leads to excessive power consumption as the GPU
is kept at max clocks (until the failsafe mechanism fires of explicitly
downclocking the GPU when all requests are idle). Or equally as bad for
the UX, the GPU is kept at minimum clocks and prevented from upclocking
in response to a requirement for more power.

Testcase: pm_rps/blocking
Cc: Deepak S <deepak.s@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Not implementing this W/A can lead to hangs.

Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we can use different cursor size, we can not hardcode 64 pixels
as the cursor width anymore.

v2: Apply to 965gm/g4x paths as well

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we use different rps events for different platforms or due to wa,
we might end up needing this logic in a lot of places. Instead of
this let's use a variable in dev_priv to track the enabled PM
interrupts.

v2: Initialize pm_rps_events in intel_irq_init() (Ville).
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Frob the commit message a bit since the English was a bit too
garbled ;-) ]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the renamed RPS struct members, it's easier to skip the local
variables which no longer clarify anything, and if anything just make
the code harder to read.

The real motivation for this patch is actually the next patch, which
attempts to consolidate some of the functionality.

Cc: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The names of the struct members for RPS are stupid. Every time I need to
do anything in this code I have to spend a significant amount of time to
remember what it all means. By renaming the variables (and adding the
comments) I hope to clear up the situation. Indeed doing this make some
upcoming patches more readable.

I've avoided ILK because it's possible that the naming used for Ironlake
matches what is in the docs. I believe the ILK power docs were never
published, and I am too lazy to dig them up.

v2: leave rp0, and rp1 in the names. It is useful to have these limits
available at times. min_freq and max_freq (which may be equal to rp0, or
rp1 depending on the platform) represent the actual HW min and max.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

this leaves a temporarily awkward min_delay (the soft limit) with the
new min_freq (the hardware limit). It's fixed in the next patch.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The existing code (which I changed last) was very convoluted. I believe
it was attempting to skip the overclock portion if the previous pcode
write failed. When I last touched the code, I was preserving this
behavior. There is some benefit to doing it that way in that if the
first pcode access fails, the later is likely invalid.

Having a bit more confidence in my understanding of how things work, I
now feel it's better to have clear, readable, code than to try to skip
over this one operation in an unusual case.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Function intel_init_runtime_pm is supposed to start allowing runtime
PM from that point, but it's called very late on the driver
initialization code, to prevent the driver from trying to suspend
while still initializing. The problem is that variables are accessed
earlier than that, so initalize them at intel_pm_setup, which is
supposed to be the correct place.

Notice that this shouldn't fix any specific bugs because dev_priv is
zeroed when allocated, so the value is already correct right from the
start.

v2: - Rebase.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The only remaining field of the struct was the lock, which was
useless.

v2: - Rebase.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When other platforms add runtime PM support they will also need to
disable interrupts, so move the variable to the runtime PM struct.

Also notice that the longer-term goal is to completely kill the
regsave struct, and I even have patches for that.

v2: - Rebase.
v3: - Rebase.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It was just being used on debugfs and on a WARN inside
hsw_set_power_well. But now that we PC8 is part of runtime PM and we
get/put runtime PM when we get/put any power domain, we shouldn't need
the WARN anymore.

v2: - Rebase.
v3: - Rebase.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because we already get/put runtime PM every time we get/put any power
domain, and now PC8 and runtime PM are the same thing.

With this, we can also now kill the hsw_{en,dis}able_package_c8
functions.

v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because we merged the PC8 and runtime PM features, so calling
intel_runtime_pm_get now has the same meaning, and we plan to just
remove hsw_disable_package_c8 for this exact reason.

My first patch tried to completely kill
intel_aux_display_runtime_get/put, because I was assuming that whoever
needed more than just runtime PM would have to get the appropriate
power domain instead of that, but it seems some people still want the
intel_aux_display_runtime_get abstraction, so keep it until someone
else tries to replace it with the more-standard power domain calls.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since after the latest patches it's only being used to prevent
getting/putting the runtime PM refcount.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The requirements_met variable was used to track two things: enabled
CRTCs and the power well. After the latest chagnes, we get a runtime
PM reference whenever we get any of the power domains, and we get
power domains when we enable CRTCs or the power well, so we should
already be covered, not needing this specific tracking.

v2: - Rebase.
v3: - Rebase.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Any power domain will require the HW to be in PCI D0 state, so just do
the simple thing.

Dear maintainer: since intel_display_power_put() and
intel_display_power_get() are almost identical, git-am has failed
apply the patch on my local machine once: it added both chunks to
put(), instead of one chunk to get() and another to put(). When you
apply this patch to your tree, please check if it is correct.

v2: - Add the warning above.
v3: - Rebase.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently, when our driver becomes idle for i915.pc8_timeout (default:
5s) we enable PC8, so we save some power, but not everything we can.
Then, while PC8 is enabled, if we stay idle for more
autosuspend_delay_ms (default: 10s) we'll enter runtime PM and put the
graphics device in D3 state, saving even more power. The two features
are separate things with increasing levels of power savings, but if we
disable PC8 we'll never get into D3.

While from the modularity point of view it would be nice to keep these
features as separate, we have reasons to merge them:
 - We are not aware of anybody wanting a "PC8 without D3" environment.
 - If we keep both features as separate, we'll have to to test both
   PC8 and PC8+D3 code paths. We're already having a major pain to
   make QA do automated testing of just one thing, testing both paths
   will cost even more.
 - Only Haswell+ supports PC8, so if we want to add runtime PM support
   to, for example, IVB, we'll have to copy some code from the PC8
   feature to runtime PM, so merging both features as a single thing
   will make it easier for enabling runtime PM on other platforms.

This patch only does the very basic steps required to have PC8 and
runtime PM merged on a single feature: the next patches will take care
of cleaning up everything.

v2: - Rebase.
v3: - Rebase.
    - Fully remove the deprecated i915 params since Daniel doesn't
      consider them as part of the ABI.
v4: - Rebase.
    - Fix typo in the commit message.
v5: - Rebase, again.
    - Add a huge comment explaining the different forcewake usage
      (Chris, Daniel).
    - Use open-coded forcewake functions (Daniel).
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function is only used on ILK+, so rename it accordingly.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make sure the line_time_us isn't zero in the gmch watermarks code as
that would cause a div by zero. This can be triggered by specifying
a very fast pixel clock for the mode.

At some point we should probably just switch over to using the same
math we use on PCH platforms which avoids such intermediate rounded
results.

Also we should verify the user provided mode much more rigorously.
At the moment we accept pretty much anything.

Note that "very fast mode" here means above 74.25 GHz.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Add Ville's clarification of what "very fast" means.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Based on an early draft from Jesse.

Add support for powering on/off the dynamic power wells on VLV by
registering its display and dpio dynamic power wells with the power
domain framework.

For now power on all PHY TX lanes regardless of the actual lane
configuration. Later this can be optimized when the PHY side setup
enables only the required lanes. Atm, it enables all lanes in all
cases.

v2:
- undef function local COND macro after its last use (Ville)
- Take dev_priv->irq_lock around the whole sequence of
  intel_set_cpu_fifo_underrun_reporting_nolock() and
  valleyview_disable_display_irqs(). They are short and releasing
  the lock in between only makes proving correctness more difficult.
- sanitize local var names in vlv_power_well_enabled()
v3:
- rebase on latest -nightly
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict due to my changes in the previous patch.
Also throw in an assert_spin_locked for safety. And finally appease
checkpatch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Suggested by Daniel.

v2:
- sanitize the state checking condition, the original was rather
  confusing (partly due to the unfortunate naming of
  i915.disable_power_well) (Ville)
- simpler message+backtrace generation by using WARN instead of WARN_ON
  (Ville)
- check if always-on power wells are truly on all the time
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to do the same for other platforms in upcoming patches.

v2:
- s/p/pipe (Ville)
- Call the new helper with the vbl_lock already held. The part it
  protects is short, so releasing it between pipes only makes proving
  correctness more difficult.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with Damien's s/p/pipe/ change.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Parts that poke port specific HW blocks like the encoder HW state
readout or connector hotplug detect code need a way to check whether
required power domains are on or enable/disable these. For this purpose
add a set of power domains that refer to the port HW blocks. Get the
proper port power domains during modeset.

For now when requesting the power domain for a DDI port get it for a 4
lane configuration. This can be optimized later to request only the 2
lane power domain, when proper support is added on the VLV PHY side for
this. Atm, the PHY setup code assumes a 4 lane config in all cases.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reading code free of special cases wins over the small overhead of
calling a noop handler. Suggested by Jesse.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split the 'set' power well handler into an 'enable', 'disable' and
'sync_hw' handler. This maps more conveniently to higher level
operations, for example it allows us to push the hsw package c8 handling
into the corresponding hsw/bdw enable/disable handlers and the hsw BIOS
hand-over setting into the hsw/bdw sync_hw handler.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Appease checkpatch's whitespace complaints.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Whenever we request a power domain it has to guarantee that all HW
resources are enabled that are needed to access a HW register associated
with that power domain. In case a register is on an always-on power well
this won't result in turning on a power well, but it may require
enabling some other HW resource. One such resource is the HSW/BDW device
D0 state that is required for all register accesses and thus for all
power wells/power domains.

So far the init power domain (guaranteeing access to all HW registers)
was part of the default i9xx always-on power well, but not the HSW/BDW
always-on power wells. Add the domain to the latter power wells too.

Atm, all the always-on power wells have noop handlers, so this doesn't
change the functionality.

v2:
- clarify semantics of always-on power wells (Paulo)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These macros are used only locally, so move them to the .c file.

No functional change.

v2:
- add init power domain to always-on power wells in the following
  - separate - patch (Paulo)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These functions are used only by a single call site and are simple
enough to just fold them in.

Note that in later patches the parts folded in here are further
simplified as we'll remove hsw_{disable,enable}_package_c8 and the NULL
check of the power well enable/disable handlers. All this means that at
the end intel_display_power_get/put() becomes more understandable as we
don't need to jump between two functions when reading the code.

No functional change.

v2:
- clarify the rational for the change (Chris)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>