Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: typo, nodes in address ascending order, shrink cmdline]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Currently ARCH_BCM has been used for Broadcom
Mobile V7 based SoCs. In order to allow other Broadcom
SoCs to also use mach-bcm directory and files, this patch
renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing
in mach-bcm directory.
Signed-off-by: NChristian Daudt <bcm@fixthebug.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Main hardware parts of the (Armada 370 based) NETGEAR ReadyNAS 104 are
supported by mainline kernel (USB 3.0 rear ports, USB 2.0 front port,
Gigabit controller and PHYs, serial port, LEDs, buttons, SATA ports,
G762 fan controller) and referenced in provided .dts file. Some additonal
work remains for:

 - Intersil ISL12057 I2C RTC and Alarm chip: working driver but needs
   to be splitted for submission of RTC part first;
 - Front LCD (Winstar 1602G): driver needs to be written
 - Armada NAND controller (to access onboard 128MB of NAND): support
   being pushed by @free-electrons people
 - 4 front SATA LEDs controlled via GPIO brought by NXP PCA9554:
   driver is available upstream. Not referenced/tested yet.

but the device is usable w/o those.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The OpenBlocks A7 board is designed and sold by PlatHome, and based on
a Kirkwood 6283 Marvell SoC. It is quite similar to the OpenBlocks A6
already supported in the kernel, with the following main differences:

 - The A6 uses a RTC on I2C, while the A7 uses the internal SoC RTC.

 - The A6 has one Ethernet port, while the A7 has two Ethernet ports

 - The A6 has only one USB port, while the A7 integrates a USB hub,
   which provides two front-side USB port, and an internal USB port as
   well.

 - The A6 has 512 MB of RAM, while the A7 has 1 GB of RAM.

 - Slightly different GPIOs for some functions.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

NanoBone Specification:
-----------------------
CPU:
  TI AM335x

Memory:
  256MB DDR3
  128MB NOR flash
  128KB FRAM

Ethernet:
  2 x 10/100 connected to SMSC LAN8710 PHY

USB:
  1 x USB2.0 Type A

I2C:
  2Kbit EEPROM (Microchip 24AA02)
  RTC (Maxim DS1338)
  GPIO Expander (Microchip MCP23017)

Expansion connector:
  6 x UART
  1 x MMC/SD
  1 x USB2.0
Signed-off-by: NMark Jackson <mpfj@newflow.co.uk>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add minimal DT support for Nokia N950 & N9 phones. The same functionality
that is provided by the current board file should work: serial console,
USB, OneNAND and MMC.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I've tested serial, MMC, smsc911x and wl12xx on zoom3. As my
omap is an early ES revision, I have not been able to test
off-idle on this one. But anyways, I'd say we have enough
device tree support for the zoom to be able to drop the
board-zoom files. Patches are welcome to add further features
to this .dts file.
Signed-off-by: NTony Lindgren <tony@atomide.com>

I've tested the serial, MMC, smsc911x, wl12xx, and off-idle support
with the pinctrl patches, so it probably works better than the
board-*.c files ever did. Also the board-omap3evm.c file is broken
for the DSS, and has been for a while. Patches are welcome to fix
it in this .dts file, let's just drop the board-*.c file for this.

Note that off-idle currently requires doing request_irq() on the
wake-up pin from pinctrl-single IRQ domain until we can handle
that in some Linux generic way.

[tony@atomide.com: updated for make dtbs build fix]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.

The board adds the following connectivity:

    o USB OTG
    o USB HOST
    o HDMI
    o Ethernet
    o Serial Debug (3.3V)
    o 2x46 pin headers
    o EEPROM
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add support for a new SOCFPGA board that has an Arria V FPGA along with
dual ARM Cortex-A9 cores.
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: devicetree@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org

This adds basic support for the terasic SoCkit board.
The board includes an Altera Cyclone 5 SoC.

[Dinh Nguyen] - Changed to 115200 for baudrate in dts bootargs
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>

The current socfpga_cyclone5.dts describes the Altera Cyclone5 SoC Development
Kit. The Cyclone5 includes a SoCFPGA, which itself can be included in other
SoC+FPGA combinations.

Instead of having to describe all Cyclone5 common nodes in every board specific
dts, move socfpga_cyclone5.dts to a dtsi and include this in a new dts for the
Development Kit.

[Dinh Nguyen] - Changed to 115200 for baudrate in dts bootargs
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>

Add support for the Tegra124 based Venice2 reference board.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This adds device tree with necessary support to boot with functional
video (on both emulator and real N900 device).
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Cubietech introduced a new cubieboard, the CubieTruck. This board added
more output connectors and features 2 GiB of RAM and a Gigabit PHY.

Tested are are uart0 and LEDS which both work as expected.
Signed-off-by: NOliver Schinagl <oliver@schinagl.nl>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now when the legacy DTS file emev2-kzm9d.dts can be
used with board-kzm9d.c and board-kzm9d-reference.c
proceed with removing emev-kzm9d-reference.dts.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Genmai base board support making use of 128 MiB of memory,
the r7s7211 SoC with the SCIF2 serial port and CA9 core.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This board is based on the M28 SoM with custom baseboard. Supported
are LEDs, ethernet, PWM, LCD, SD slots.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The Armada XP Matrix board is the mother board of a more complex
system. The mother board uses an Armada XP MV78460, 4 serial ports, 2
SATA ports, one Ethernet connection, a PCIe port and a USB port. All
those devices are enabled in the Device Tree added by this patch.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

As the device tree conversion did away with the ability to
auto-detect the UIB (User Interface Board) version from attempting
to read an I2C address, we now have to pass the knowledge of
what UIB is mounted through the device tree. This gives rise
to four possible board permutations:

- HREF prior to v60, ST UIB (hrefprev60-stuib)
- HREF prior to v60, TVK1281618 UIB (hrefprev60-tvk)
- HREF v60 and later, ST UIB (href60plus-stuib)
- HREF v60 and later, TVK1281618 UIB (hrefv60plus-tvk)
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Makefile missed to include atlas6-evb.dtb for ARCH_ATLAS6.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This adds an initial DT file for the Globalscale D3Plug with Dove SoC.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Koelsch base board support making use of 2 GiB of memory,
the r8a7791 SoC with the SCIF0 serial port and CA15 with
CMT timer.
Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: NRyo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready SMP/PFC]
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

For more information about the Udoo board:
http://www.udoo.org/Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add initial PHYTEC VF610 Cosmic/Cosmic+ board support with
UART and FEC enabled.
Signed-off-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Use a standard 'qcom' prefix to denotate device trees meant for Qualcomm
based processors.
Signed-off-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>

The BeagleBone Black is basically a regular BeagleBone with eMMC and
HDMI added, so create a common dtsi both can use.

IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI
transceiver after a dozen boots with an uSD card inserted because LDO
will be at 3.3V instead of 1.8.

MMC support for AM335x still isn't in, so only the LDO change has been
added.
Signed-off-by: NKoen Kooi <koen@dominion.thruhere.net>
Tested-by: NTom Rini <trini@ti.com>
Tested-by: NMatt Porter <matt.porter@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This patch adds basic device tree sources for SAMSUNG SMDK6410 board
based on SAMSUNG S3C6410 SoC.

Currently only UARTs, SD channel 0 and 100Mbps ethernet (SMSC911x) are
supported.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds basic device tree sources for FriendlyARM Mini6410 board
based on Samsung S3C6410 SoC.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add support for the imx6q wanboard variant.

Since imx6q/dl are pin to pin compatible, introduce the imx6qdl-wandboard.dtsi
file that contains the common peripheral nodes.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Board files for Phytec phyCARD-S "System on Module" and "Rapid
Development Kit".

Based on patches from:

Steffen Trumtrar <s.trumtrar@pengutronix.de>:
 - Original patch
 - ARM: dts: Set partition offsets for phycard
 - ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100
 - ARM: imx27-phytec-phycard-S.dts: resize nand partitions

Jan Luebbe <jlu@pengutronix.de>:
 - ARM: dts: Enable bad block table in NAND

Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The Cubieboard2 is the successor of the first Cubieboard, and shares the
same hardware, except that the Allwinner A10 found initially has been
replaced by an Allwinner A20.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Olimex A20-Olinuxino is an open-hardware board based on the
Allwinner A20 SoC, with most of the pins exported on headers, a 10/100M
ethernet port, SATA, SD and uSD slots, etc.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This platform from WITS is the evaluation board for the Allwinner A31.
It features a quad-Cortex A7, 2048MB of RAM, NAND, USB, MMC, several
UART, HDMI, a 2048 x 1536 10" screen, powered by a PowerVR, etc.

Of course, most of these peripherals aren't supported yet, but support
for those will come eventually.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The CFA-10058 is a breakout board for the CFA-10036 that has Ethernet, USB and a
5" LCD screen on it.
Signed-off-by: NBrian Lilly <brian@crystalfontz.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The CFA-10056 is a breakout board for the CFA-10036, and is
basically a CFA-10037, with a 4.3" screen.
Signed-off-by: NBrian Lilly <brian@crystalfontz.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The patch set beginning with commit:
"ARM: ux500: Apply a ste-* prefix onto snowball.dts"
thru commit:
"ARM: ux500: Remove u9540.dts as it's been replaced"
altered the names of the ux500 device tree files but forgot
to:

- Rename the ccu8540-pinctrl.dtsi file

- Update #include statements from files using these
  files, so the build broke.

- Update the Makefile for the device trees so the build
  broke.

Fix it up so we can build them all again.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>

This adds a device tree usable on Mele A1000 (and A2000, as it
apparently is the same device except for the case). This device features
one UART port, Ethernet, an AXP209 PMU on i2c0 and two user configurable
LEDs.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
[maxime: fixed the soc node address]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>