“584320156b7e42e74105ca78bdf895d2b0269251”上不存在“git@gitcode.net:openeuler/kernel.git”
- 18 9月, 2015 1 次提交
-
-
由 Oleksij Rempel 提交于
Current kernel support only one fw name with theoretically only one fw version located in “firmware/htc_[9271|7010].fw”. Which is ok so far we have only one fw version (1.3). After we realised new fw 1.4, we faced compatibility problem which was decided to solve by firmware name and location: - new firmware is located now in firmware/ath9k_htc/htc_[9271|7010]-1.4.0.fw - old version 1.3 should be on old place, so old kernel have no issues with it. - new kernels including this patch should be able to try different supported (min..max) fw version. - new kernel should be able to support old fw location too. At least for now. At same time this patch will add new module option which should allow user to play with development fw version without replacing stable one. If user will set “ath9k_htc use_dev_fw=1” module will try to find firmware/ath9k_htc/htc_[9271|7010]-1.dev.0.fw first and if it fails, use stable version: for example...1.4.0.fw. Signed-off-by: NOleksij Rempel <linux@rempel-privat.de> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
- 11 9月, 2015 1 次提交
-
-
由 Andy Shevchenko 提交于
Instead of custom approach let's use recently introduced seq_hex_dump() helper. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Joe Perches <joe@perches.com> Cc: Tadeusz Struk <tadeusz.struk@intel.com> Cc: Helge Deller <deller@gmx.de> Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 26 8月, 2015 5 次提交
-
-
由 Raja Mani 提交于
Below compilation warnings are observed in gcc version 4.8.2. Even though it's not seen in bit older gcc versions (for ex, 4.7.3), It's good to fix it by changing format specifier from %d to %zd in wmi pull phyerr functions. wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev': wmi.c:3567:8: warning: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Wformat=] left_len, sizeof(*phyerr)); ^ wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev': wmi.c:3612:8: warning: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Wformat=] left_len, sizeof(*phyerr)); ^ Fixes: 991adf71 ("ath10k: refactor phyerr event handlers") Fixes: 2b0a2e0d ("ath10k: handle 10.4 firmware phyerr event") Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
This adds additional 0x0041 PCI Device ID definition to ath10k for QCA6164 which is a 1 spatial stream sibling of the QCA6174 (which is 2 spatial stream chip). The QCA6164 needs a dedicated board.bin file which is different than the one used for QCA6174. If the board.bin is wrong the device will crash early while trying to boot firmware. The register dump will look like this: ath10k_pci 0000:02:00.0: firmware register dump: ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31 ... Note the value 0x000A012D. Special credit goes to Alan Liu <alanliu@qca.qualcomm.com> for providing support help which enabled me to come up with this patch. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Raja Mani 提交于
To enable/configure spectral scan parameters in 10.4 firmware, existing wmi spectral related functions can be reused. Link those functions in 10.4 wmi ops table. In addition, adjust bin size (only when size is 68 bytes) before reporting bin samples to user space. The background for this adjustment is that qca99x0 reports bin size as 68 bytes (64 bytes + 4 bytes) in report mode 2. First 64 bytes carries in-band tones (-32 to +31) and last 4 byte carries band edge detection data (+32) mainly used in radar detection purpose. Additional last 4 bytes are stripped to make bin size valid one. This bin size adjustment will happen only for qca99x0, all other chipsets will report proper bin sizes (64/128) without extra 4 bytes being added at the end. The changes are validated in qca99x0 using 10.4 firmware. Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
The function returns 1 when DMA mapping fails. The driver would return bogus values and could possibly confuse itself if DMA failed. Fixes: 767d34fc ("ath10k: remove DMA mapping wrappers") Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Kernel would complain about leaving a held lock after going back to userspace and would subsequently deadlock. Fixes: e04cafbc ("ath10k: fix peer limit enforcement") Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 25 8月, 2015 1 次提交
-
-
由 Oleksij Rempel 提交于
current code will handle -ETIMEDOUT as success which is probalbly wrong. According to this comment I assume it is safe to handle -ETIMEDOUT as false: drivers/net/wireless/ath/ath9k/calib.c 290 /* 291 * We timed out waiting for the noisefloor to load, probably due to an 292 * in-progress rx. Simply return here and allow the load plenty of time 293 * to complete before the next calibration interval. We need to avoid 294 * trying to load -50 (which happens below) while the previous load is 295 * still in progress as this can cause rx deafness. Instead by returning 296 * here, the baseband nf cal will just be capped by our present 297 * noisefloor until the next calibration timer. 298 */ Since no other error wariants are present, this patch is checking only for (ret <= 0). Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NOleksij Rempel <linux@rempel-privat.de> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
- 21 8月, 2015 1 次提交
-
-
由 Johannes Berg 提交于
This reduces code size slightly (at least on x86/64) while also removing memory consumption by two unsigned long values for each ath5k device. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 8月, 2015 2 次提交
-
-
由 Raja Mani 提交于
If .pull_fw_stats() fails for some reason while processing fw stats event, collected pdev/vdev/peer stats just before the failure should be freed. This is unlikely to happen, just code review catch. Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Raja Mani 提交于
Found incorrect sequence in ath10k_core_stop() where wmi pktlog disable cmd is passed from ath10k_debug_stop() to firmware immediately after wmi pdev suspend cmd. Firmware will not accept any wmi cmd after receiving wmi pdev suspend cmd. Fix this issue in ath10k_core_stop() by moving ath10k_debug_stop() just before sending pdev suspend cmd. So that pktlog disable cmd will get passed before pdev suspend cmd. Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 18 8月, 2015 1 次提交
-
-
由 Miaoqing Pan 提交于
MAC/BB name is"????" if the MAC/BB is unknown. Signed-off-by: NMiaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
- 17 8月, 2015 9 次提交
-
-
WMI 10.4 uses the same command interface as QCA988X for addba/delba debug wmi commands. Fill wmi_10_4_ops table with the functions used for QCA988X for these commands. With this change, the following debugfs entries can be used to configure the aggregation mode and to send addba request, addba response and delba respectively in manual aggregation mode for QCA99X0 chip. /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/aggr_mode /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba_resp /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/delba Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Raja Mani 提交于
Header format of 10.4 firmware phyerr event is not alligned with pre 10.4 firmware. Introduce new wmi handlers to parse 10.4 firmware specific phyerror event header. With changes covered in this patch, radar detection works on qca9x0 hw 2.0 which uses 10.4 firmware. Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Raja Mani 提交于
Existing phyerr event handlers directly uses phyerr header format (ie, struct wmi_phyerr and struct wmi_phyerr_event) in the code exactly on how firmware packs it. This is the problem in 10.4 fw specific phyerr event handling where it uses different phyerror header format. Before adding 10.4 specific handler, little bit of refactor is done in existing phyerr handlers. Two new abstracted structures (struct wmi_phyerr_ev_hdr_arg and struct wmi_phyerr_ev_arg) are introduced to remove dependency of using firmware specific header format in the code. So that firmware specific phyerror handlers can populate values to abstracted structures and the following code can use abstracted struct for further operation. .pull_phyerr_hdr is added newly to pull common phyerr header info like tsf, buf_len, number of phyerr packed. Existing .pull_phyerr handler is changed and called to parse every sub phyerrs in the event. Validated these refactoring on qca988x hw2.0 using fw 10.2.4 version. Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Nicholas Mc Guire 提交于
Return type of wait_for_completion_timeout is unsigned long not int. As remain is exclusively used for wait_for_completion_timeout here its type is simply changed to unsigned long. API conformance testing for completions with coccinelle spatches are being used to locate API usage inconsistencies: ./drivers/net/wireless/ath/wil6210/wmi.c:827 int return assigned to unsigned long Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m, CONFIG_WIL6210=m Patch is against 4.1-rc3 (localversion-next is -next-20150514) Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Apparently it's not safe to install both pairwise and groupwise keys on AP vdevs as it can cause traffic to stop working in some multi-vif (WPA+WEP) cases. Fixes: ce90b271 ("ath10k: fix multiple key static wep with ibss") Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
The frequency at which cycle/rx_clear counters are running might change from one target type to another. QCA99X0 is running the counters at 150Mhz while QCA9888X and QCA6174 are running at 88Mhz. Add a new entry to hw_params to store the target specific frequency and use it in msecs conversion. This change fixes inconsistent channel active/busy time. Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
There are three WMI_CHAN_INFO events reported per channel in QCA99X0 firmware. First one is a notification at the begining of the channel dwell time with cmd_flag as CHAN_INFO_START(cmd_flag = 0), second one is a notification at the end of the dwell time with cmd_flag CHAN_INFO_PRE_COMPLETE (cmd_flag = 2) and the third is the indication with CHAN_INFO_COMPLETE (cmd_flag = 1) which is the last indication for the channel. Since there is a new state before the completion, the handler is to fixed so that the counts are deducted from the ones reported with CHAN_INFO_START rather than the ones reported with CHAN_INFO_PRE_COMPLETE. Without this fix there will be lots of 0 msecs reported as active and busy time. Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Vif's vdev_id is used as queue number. However due to the tx pausing design in ath10k it was possible for a new interface to be created with its tx queue stopped (via ieee80211_stop_queues). This could in turn leave the interface inoperable until ath10k_mac_tx_unlock() was called. This problem only affected multi-vif scenarios when new interfaces were created some time later after other interfaces have been running for some time and had Tx queue full at some point prior. Possible manifestation of the bug was authentication timeout for a client vif. Fixes: 96d828d4 ("ath10k: rework tx queue locking") Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Once HTT Tx queue got full offchannel queue was stopped and never woken up again. This broke, e.g. P2P. This could be reproduced after running a lot of traffic enough to saturate 100% of the driver Tx queue and then trying to send offchannel traffic. Fixes: 96d828d4 ("ath10k: rework tx queue locking") Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 13 8月, 2015 12 次提交
-
-
由 Nicholas Mc Guire 提交于
Return type of wait_for_completion_timeout is unsigned long not int. As time_left is exclusively used for wait_for_completion_timeout here its type is simply changed to unsigned long. API conformance testing for completions with coccinelle spatches are being used to locate API usage inconsistencies: ./drivers/net/wireless/ath/ath9k/link.c:197 int return assigned to unsigned long Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m, Patch is against 4.1-rc3 (localversion-next is -next-20150514) Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Nicholas Mc Guire 提交于
Return type of wait_for_completion_timeout is unsigned long not int. As time_left is exclusively used for wait_for_completion_timeout here its type is simply changed to unsigned long. API conformance testing for completions with coccinelle spatches are being used to locate API usage inconsistencies: ./drivers/net/wireless/ath/ath9k/wmi.c:331 int return assigned to unsigned long Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m, CONFIG_ATH9K_HTC=m Patch is against 4.1-rc3 (localversion-next is -next-20150514) Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Nicholas Mc Guire 提交于
Return type of wait_for_completion_timeout is unsigned long not int. As time_left is exclusively used for wait_for_completion_timeout here its type is simply changed to unsigned long. API conformance testing for completions with coccinelle spatches are being used to locate API usage inconsistencies: ./drivers/net/wireless/ath/ath9k/htc_drv_init.c:81 int return assigned to unsigned long Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m, CONFIG_ATH9K_HTC=m Patch is against 4.1-rc3 (localversion-next is -next-20150514) Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Nicholas Mc Guire 提交于
Return type of wait_for_completion_timeout is unsigned long not int. As time_left is exclusively used for wait_for_completion_timeout here its type is simply changed to unsigned long. API conformance testing for completions with coccinelle spatches are being used to locate API usage inconsistencies: ./drivers/net/wireless/ath/ath9k/htc_hst.c:171 int return assigned to unsigned long ./drivers/net/wireless/ath/ath9k/htc_hst.c:277 int return assigned to unsigned long ./drivers/net/wireless/ath/ath9k/htc_hst.c:206 int return assigned to unsigned long Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m, CONFIG_ATH9K_HTC=m Patch is against 4.1-rc3 (localversion-next is -next-20150514) Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Michal Kazior 提交于
Firmware peer entries are involved in internal firmware vdev structures. This was not accounted for and could lead firmware to crash due to asking it to do more than it could. Fixes: 039a0051 ("ath10k: allocate fw resources for iface combinations") Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
If peer creation failed during offchannel Tx the driver attempted to delete the peer nonetheless. This caused the ar->num_peers counter to be incorrectly decremented. This subsequently could cause the counter to drop below 0 and also eventually lead to firmware crash because host would think there are less peer entries created in firmware then there really were. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
When WoWLAN resume fails with retval 1 mac80211 will attempt to reconfig the device in a similar manner when hw restart is requested. This wasn't handled properly and yielded call trace warnings and the device ended up not working. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
If firmware did not have any feature flags set the var would be left with values found on the stack (i.e. garbage) yielding print string like this: (...) features \xffffffa6m:^R\xfffffffbԂ\xffffffc4^E Fixes: b27bc5a4 ("ath10k: dump fw features during probing") Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Vivek Natarajan 提交于
This patch enables MU-MIMO transmit beamforming support for QCA99X0 chipsets. Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Vivek Natarajan 提交于
qca61x4 uses the vdev param as a sole sufficient configuration for txbf while qca99x0 enables txbf during peer assoc by combining the vdev param value with peer assoc's vht capabilities This patch gets the appropriate txbf configuration scheme before passing the wmi command to enable the same in the firmware. Signed-off-by: NVivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Even though there's a WMI enum for fragmentation threshold no known firmware actually implements it. Moreover it is not possible to rely frame fragmentation to mac80211 because firmware clears the "more fragments" bit in frame control making it impossible for remote devices to reassemble frames. Hence implement a dummy callback just to say fragmentation isn't supported. This effectively prevents mac80211 from doing frame fragmentation in software. This fixes Tx becoming broken after setting fragmentation threshold. Fixes: 1010ba4c ("ath10k: unregister and remove frag_threshold callback") Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
由 Michal Kazior 提交于
Commit 1010ba4c ("ath10k: unregister and remove frag_threshold callback") didn't remove all instances of (futile) fragmentation threshold configuration. No known firmware supports the parameter so don't even bother setting it. Signed-off-by: NMichal Kazior <michal.kazior@tieto.com> Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
-
- 11 8月, 2015 1 次提交
-
-
由 Bertold Van den Bergh 提交于
Make ath_opmode_to_string return "OCB" for NL80211_IFTYPE_OCB. Currently it will return "UNKNOWN". Signed-off-by: NBertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
- 07 8月, 2015 2 次提交
-
-
由 Masahiro Yamada 提交于
Looks like the word "contiguous" is often mistyped. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: NJiri Kosina <jkosina@suse.com>
-
由 Felix Fietkau 提交于
kbuild bot reported that commit 592fa228 ("ath9k: remove struct ath_atx_ac") broke the build when CONFIG_ATH9K_STATION_STATISTICS is y. Reported-by: Nkbuild test robot <fengguang.wu@intel.com> Fixes: 592fa228 ("ath9k: remove struct ath_atx_ac") Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
- 06 8月, 2015 4 次提交
-
-
由 Felix Fietkau 提交于
Use list_empty(&tid->list) instead Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Felix Fietkau 提交于
struct ath_atx_ac contains a list of active TIDs belonging to one WMM AC. This patch changes the code to track active station TIDs in the txq directly. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
由 Felix Fietkau 提交于
Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-
Setup rxfiler correctly for offchannel ctx. This fix problem we didn't configure rxfilter, next didn't receive probe requests and next failed p2p_find. This was seen when ath9k loaded with use_chanctx=1 Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
-