Signed-off-by: NGiuseppe Bilotta <giuseppe.bilotta@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Nintendo Classic Controller extension reports lots of keys, two analog sticks
and two analog buttons. We report all data through extension input device to
userspace.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The Nintendo Nunchuck extension reports accelerometer values, one analog stick
and two buttons. See inline comments for data layout.
We report all data to userspace through extension input device.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Motion+ reports rotation gyro data which we report to userspace as ABS_RX/Y/Z
values. The device reports them either in fast or slow mode. We adjust the
values to get a linear scale so userspace does not need to know about slow and
fast mode.

The motion+ also reports whether an extension is connected to it. We keep track
of this value and reinitialize the extensions if an extension is plugged or
unplugged.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

All supported extensions report data as 6 byte block. All DRMs with extension
data provide at least 6 extension bytes. Hence a generic handler for all
extension bytes is sufficient and can be called on all DRMs.

The handler distinguishes the input and passes it to the right handler. Motion+
passes data interleaved so we can have Motion+ and a regular extension enabled
simultaneously.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Motion+ and regular extensions are physical adapters for the wiimote so create
one input device for each of them. This also allows to enable only opened
extensions and turn unused extenions off to save battery power.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add new sysfs attribute "extension" which returns the currently connected and
initialized extensions.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The wiimote extension registers are not fully understood, so we always disable
all extensions on extension-port events. Then we reinitialize and reidentify
them and activate all requested extensions.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add stub functions to read and identify extensions and then initialize all
connected extensions.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The wiimote supports several extensions. This adds a separate source file which
handles all extensions and can be disabled at compile-time.

The driver reacts on "plug"-events on the extension port and starts a worker
which initializes or deinitializes the extensions.

Currently, the initialization logic is not fully understood and we can only
detect and enable all extensions when all extensions are deactivated. Therefore,
we need to disable all extensions, then detect and activate them again to react
on "plug"-events.
However, deactivating extensions will generate a new "plug"-event and we will
never leave that loop. Hence, we only support extensions if they are plugged
before the wiimote is connected (or before the ext-input device is opened). In
the future we may support full extension hotplug support, but
reverse-engineering this may take a while.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>