Someone cut and pasted md's md_trim_bio() into xen-blkfront.c. Come on,
we should know better than this.
Signed-off-by: NKent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The pre-existing sysfs interfaces which take explicit namespace
argument are weird in that they place the optional @ns in front of
@name which is contrary to the established convention.  For example,
we end up forcing vast majority of sysfs_get_dirent() users to do
sysfs_get_dirent(parent, NULL, name), which is silly and error-prone
especially as @ns and @name may be interchanged without causing
compilation warning.

This renames sysfs_get_dirent() to sysfs_get_dirent_ns() and swap the
positions of @name and @ns, and sysfs_get_dirent() is now a wrapper
around sysfs_get_dirent_ns().  This makes confusions a lot less
likely.

There are other interfaces which take @ns before @name.  They'll be
updated by following patches.

This patch doesn't introduce any functional changes.

v2: EXPORT_SYMBOL_GPL() wasn't updated leading to undefined symbol
    error on module builds.  Reported by build test robot.  Fixed.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the last process closes /dev/mdX sync_blockdev will be called so
that all buffers get flushed.
So if it is then opened for the STOP_ARRAY ioctl to be sent there will
be nothing to flush.

However if we open /dev/mdX in order to send the STOP_ARRAY ioctl just
moments before some other process which was writing closes their file
descriptor, then there won't be a 'last close' and the buffers might
not get flushed.

So do_md_stop() calls sync_blockdev().  However at this point it is
holding ->reconfig_mutex.  So if the array is currently 'clean' then
the writes from sync_blockdev() will not complete until the array
can be marked dirty and that won't happen until some other thread
can get ->reconfig_mutex.  So we deadlock.

We need to move the sync_blockdev() call to before we take
->reconfig_mutex.
However then some other thread could open /dev/mdX and write to it
after we call sync_blockdev() and before we actually stop the array.
This can leave dirty data in the page cache which is awkward.

So introduce new flag MD_STILL_CLOSED.  Set it before calling
sync_blockdev(), clear it if anyone does open the file, and abort the
STOP_ARRAY attempt if it gets set before we lock against further
opens.

It is still possible to get problems if you open /dev/mdX, write to
it, then issue the STOP_ARRAY ioctl.  Just don't do that.
Signed-off-by: NNeilBrown <neilb@suse.de>

mddev->flags is mostly used to record if an update of the
metadata is needed.  Sometimes the whole field is tested
instead of just the important bits.  This makes it difficult
to introduce more state bits.

So replace all bare tests of mddev->flags with tests for the bits
that actually need testing.
Signed-off-by: NNeilBrown <neilb@suse.de>

MD:  Remember the last sync operation that was performed

This patch adds a field to the mddev structure to track the last
sync operation that was performed.  This is especially useful when
it comes to what is recorded in mismatch_cnt in sysfs.  If the
last operation was "data-check", then it reports the number of
descrepancies found by the user-initiated check.  If it was a
"repair" operation, then it is reporting the number of
descrepancies repaired.  etc.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

MD: Export 'md_reap_sync_thread' function

Make 'md_reap_sync_thread' available to other files, specifically dm-raid.c.
- rename reap_sync_thread to md_reap_sync_thread
- move the fn after md_check_recovery to match md.h declaration placement
- export md_reap_sync_thread
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

MD: Prevent sysfs operations on uninitialized kobjects

Device-mapper does not use sysfs; but when device-mapper is leveraging
MD's RAID personalities, MD sometimes attempts to update sysfs.  This
patch adds checks for 'mddev-kobj.sd' in sysfs_[un]link_rdev to ensure
it is about to operate on something valid.  This patch also checks for
'mddev->kobj.sd' before calling 'sysfs_notify' in 'remove_and_add_spares'.
Although 'sysfs_notify' already makes this check, doing so in
'remove_and_add_spares' prevents an additional mutex operation.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

If a resync is aborted cleanly, ->curr_resync is a reliable
record of where we got up to.
If there was an error it is less reliable but we always know that
->curr_resync_completed is safe.

So add a flag MD_RECOVERY_ERROR to differentiate between these cases
and set recovery_cp accordingly.
Signed-off-by: NJianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

New wait_event{_interruptible}_lock_irq{_cmd} macros added. This commit
moves the private wait_event_lock_irq() macro from MD to regular wait
includes, introduces new macro wait_event_lock_irq_cmd() instead of using
the old method with omitting cmd parameter which is ugly and makes a use
of new macros in the MD. It also introduces the _interruptible_ variant.

The use of new interface is when one have a special lock to protect data
structures used in the condition, or one also needs to invoke "cmd"
before putting it to sleep.

All new macros are expected to be called with the lock taken. The lock
is released before sleep and is reacquired afterwards. We will leave the
macro with the lock held.

Note to DM: IMO this should also fix theoretical race on waitqueue while
using simultaneously wait_event_lock_irq() and wait_event() because of
lack of locking around current state setting and wait queue removal.
Signed-off-by: NLukas Czerner <lczerner@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Now that multiple threads can handle stripes, it is safer to
use an atomic64_t for resync_mismatches, to avoid update races.
Signed-off-by: NJianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Change the thread parameter, so the thread can carry extra info. Next patch
will use it.
Signed-off-by: NShaohua Li <shli@fusionio.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

This will allow md/raid to know why the unplug was called,
and will be able to act according - if !from_schedule it
is safe to perform tasks which could themselves schedule.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Both md and umem has similar code for getting notified on an
blk_finish_plug event.
Centralize this code in block/ and allow each driver to
provide its distinctive difference.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

This seemed like a good idea at the time, but after further thought I
cannot see it making a difference other than very occasionally and
testing to try to exercise the case it is most likely to help did not
show any performance difference by removing it.

So remove the counting of active plugs and allow 'pending writes' to
be activated at any time, not just when no plugs are active.

This is only relevant when there is a write-intent bitmap, and the
updating of the bitmap will likely introduce enough delay that
the single-threading of bitmap updates will be enough to collect large
numbers of updates together.

Removing this will make it easier to centralise the unplug code, and
will clear the other for other unplug enhancements which have a
measurable effect.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

If we are to allow bitmaps to be resized when the array is resized,
we need to know how much space there is.

So create an attribute to store this information and set appropriate
defaults.

It can be set more precisely via sysfs, or future metadata extensions
may allow it to be recorded.
Signed-off-by: NNeilBrown <neilb@suse.de>

dm-raid currently open-codes the freeing of some members of
and rdev.  It is more maintainable to have it call common code
from md.c which does this for all call-sites.

So remove free_disk_sb to md_rdev_clear, export it, and use it in
dm-raid.c
Signed-off-by: NNeilBrown <neilb@suse.de>

When reshaping we can avoid costly intermediate backup by
changing the 'start' address of the array on the device
(if there is enough room).

So as a first step, allow such a change to be requested
through sysfs, and recorded in v1.x metadata.

(As we didn't previous check that all 'pad' fields were zero,
 we need a new FEATURE flag for this.
 A (belatedly) check that all remaining 'pad' fields are
 zero to avoid a repeat of this)

The new data offset must be requested separately for each device.
This allows each to have a different change in the data offset.
This is not likely to be used often but as data_offset can be
set per-device, new_data_offset should be too.

This patch also removes the 'acknowledged' arg to rdev_set_badblocks as
it is never used and never will be.  At the same time we add a new
arg ('in_new') which is currently always zero but will be used more
soon.

When a reshape finishes we will need to update the data_offset
and rdev->sectors.  So provide an exported function to do that.
Signed-off-by: NNeilBrown <neilb@suse.de>

Currently a reshape operation always progresses from the start
of the array to the end unless the number of devices is being
reduced, in which case it progressed in the opposite direction.

To reverse a partial reshape which changes the number of devices
you can stop the array and re-assemble with the raid-disks numbers
reversed and it will undo.

However for a reshape that does not change the number of devices
it is not possible to reverse the reshape in the middle - you have to
wait until it completes.

So add a 'reshape_direction' attribute with is either 'forwards' or
'backwards' and can be explicitly set when delta_disks is zero.

This will become more important when we allow the data_offset to
change in a reshape.  Then the explicit statement of what direction is
being used will be more useful.

This can be enabled in raid5 trivially as it already supports
reverse reshape and just needs to use a different trigger to request it.
Signed-off-by: NNeilBrown <neilb@suse.de>

Currently we don't honour merge_bvec_fn in member devices so if there
is one, we force all requests to be single-page at most.
This is not ideal.

So enhance the raid10 merge_bvec_fn to check that function in children
as well.

This introduces a small problem.  There is no locking around calls
the ->merge_bvec_fn and subsequent calls to ->make_request.  So a
device added between these could end up getting a request which
violates its merge_bvec_fn.

Currently the best we can do is synchronize_sched().  This will work
providing no preemption happens.  If there is preemption, we just
have to hope that new devices are largely consistent with old devices.
Signed-off-by: NNeilBrown <neilb@suse.de>

md.h has an 'rdev_for_each()' macro for iterating the rdevs in an
mddev.  However it uses the 'safe' version of list_for_each_entry,
and so requires the extra variable, but doesn't include 'safe' in the
name, which is useful documentation.

Consequently some places use this safe version without needing it, and
many use an explicity list_for_each entry.

So:
 - rename rdev_for_each to rdev_for_each_safe
 - create a new rdev_for_each which uses the plain
   list_for_each_entry,
 - use the 'safe' version only where needed, and convert all other
   list_for_each_entry calls to use rdev_for_each.
Signed-off-by: NNeilBrown <neilb@suse.de>

hot-replace is a feature being added to md which will allow a
device to be replaced without removing it from the array first.

With hot-replace a spare can be activated and recovery can start while
the original device is still in place, thus allowing a transition from
an unreliable device to a reliable device without leaving the array
degraded during the transition.  It can also be use when the original
device is still reliable but it not wanted for some reason.

This will eventually be supported in RAID4/5/6 and RAID10.

This patch adds a super-block flag to distinguish the replacement
device.  If an old kernel sees this flag it will reject the device.

It also adds two per-device flags which are viewable and settable via
sysfs.
   "want_replacement" can be set to request that a device be replaced.
   "replacement" is set to show that this device is replacing another
   device.

The "rd%d" links in /sys/block/mdXx/md only apply to the original
device, not the replacement.  We currently don't make links for the
replacement - there doesn't seem to be a need.
Signed-off-by: NNeilBrown <neilb@suse.de>

Soon an array will be able to have multiple devices with the
same raid_disk number (an original and a replacement).  So removing
a device based on the number won't work.  So pass the actual device
handle instead.
Reviewed-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

"mdk" doesn't mean anything any more.
Signed-off-by: NNeilBrown <neilb@suse.de>

Signed-off-by: NNeilBrown <neilb@suse.de>

Having mddev_t and 'struct mddev_s' is ugly and not preferred
Signed-off-by: NNeilBrown <neilb@suse.de>

The typedefs are just annoying. 'mdk' probably refers to 'md_k.h'
which used to be an include file that defined this thing.
Signed-off-by: NNeilBrown <neilb@suse.de>

Signed-off-by: NWang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Two related problems:

1/ some error paths call "md_unregister_thread(mddev->thread)"
   without subsequently clearing ->thread.  A subsequent call
   to mddev_unlock will try to wake the thread, and crash.

2/ Most calls to md_wakeup_thread are protected against the thread
   disappeared either by:
      - holding the ->mutex
      - having an active request, so something else must be keeping
        the array active.
   However mddev_unlock calls md_wakeup_thread after dropping the
   mutex and without any certainty of an active request, so the
   ->thread could theoretically disappear.
   So we need a spinlock to provide some protections.

So change md_unregister_thread to take a pointer to the thread
pointer, and ensure that it always does the required locking, and
clears the pointer properly.
Reported-by: N"Moshe Melnikov" <moshe@zadarastorage.com>
Signed-off-by: NNeilBrown <neilb@suse.de>
cc: stable@kernel.org

There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.

Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

It is only safe to choose not to write to a bad block if that bad
block is safely recorded in metadata - i.e. if it has been
'acknowledged'.

If it hasn't we need to wait for the acknowledgement.

We support that using rdev->blocked wait and
md_wait_for_blocked_rdev by introducing a new device flag
'BlockedBadBlock'.

This flag is only advisory.
It is cleared whenever we acknowledge a bad block, so that a waiter
can re-check the particular bad blocks that it is interested it.

It should be set by a caller when they find they need to wait.
This (set after test) is inherently racy, but as
md_wait_for_blocked_rdev already has a timeout, losing the race will
have minimal impact.

When we clear "Blocked" was also clear "BlockedBadBlocks" incase it
was set incorrectly (see above race).

We also modify the way we manage 'Blocked' to fit better with the new
handling of 'BlockedBadBlocks' and to make it consistent between
externally managed and internally managed metadata.   This requires
that each raidXd loop checks if the metadata needs to be written and
triggers a write (md_check_recovery) if needed.  Otherwise a queued
write request might cause raidXd to wait for the metadata to write,
and only that thread can write it.

Before writing metadata, we set FaultRecorded for all devices that
are Faulty, then after writing the metadata we clear Blocked for any
device for which the Fault was certainly Recorded.

The 'faulty' device flag now appears in sysfs if the device is faulty
*or* it has unacknowledged bad blocks.  So user-space which does not
understand bad blocks can continue to function correctly.
User space which does, should not assume a device is faulty until it
sees the 'faulty' flag, and then sees the list of unacknowledged bad
blocks is empty.
Signed-off-by: NNeilBrown <neilb@suse.de>

If a device has ever seen a write error, we will want to handle
known-bad-blocks differently.
So create an appropriate state flag and export it via sysfs.
Signed-off-by: NNeilBrown <neilb@suse.de>
Reviewed-by: NNamhyung Kim <namhyung@gmail.com>

Now that we have a bad block list, we should not read from those
blocks.
There are several main parts to this:
  1/ read_balance needs to check for bad blocks, and return not only
     the chosen device, but also how many good blocks are available
     there.
  2/ fix_read_error needs to avoid trying to read from bad blocks.
  3/ read submission must be ready to issue multiple reads to
     different devices as different bad blocks on different devices
     could mean that a single large read cannot be served by any one
     device, but can still be served by the array.
     This requires keeping count of the number of outstanding requests
     per bio.  This count is stored in 'bi_phys_segments'
  4/ retrying a read needs to also be ready to submit a smaller read
     and queue another request for the rest.

This does not yet handle bad blocks when reading to perform resync,
recovery, or check.

'md_trim_bio' will also be used for RAID10, so put it in md.c and
export it.
Signed-off-by: NNeilBrown <neilb@suse.de>

Space must have been allocated when array was created.
A feature flag is set when the badblock list is non-empty, to
ensure old kernels don't load and trust the whole device.

We only update the on-disk badblocklist when it has changed.
If the badblocklist (or other metadata) is stored on a bad block, we
don't cope very well.

If metadata has no room for bad block, flag bad-blocks as disabled,
and do the same for 0.90 metadata.
Signed-off-by: NNeilBrown <neilb@suse.de>

This the first step in allowing md to track bad-blocks per-device so
that we can fail individual blocks rather than the whole device.

This patch just adds a data structure for recording bad blocks, with
routines to add, remove, search the list.
Signed-off-by: NNeilBrown <neilb@suse.de>
Reviewed-by: NNamhyung Kim <namhyung@gmail.com>

Revert most of commit e384e585
  md/bitmap: prepare for storing write-intent-bitmap via dm-dirty-log.

MD should not need to use DM's dirty log - we decided to use md's
bitmaps instead.

Keeping the DIV_ROUND_UP clean-ups that were part of commit
e384e585, however.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

If we hit a read error while recovering a mirror, we want to abort the
recovery without necessarily failing the disk - as having a disk this
a read error is better than not having an array at all.

Currently this is managed with a per-array flag "recovery_disabled"
and is only implemented for RAID1.  For RAID10 we will need finer
grained control as we might want to disable recovery for individual
devices separately.

So push more of the decision making into the personality.
'recovery_disabled' is now a 'cookie' which is copied when the
personality want to disable recovery and is changed when a device is
added to the array as this is used as a trigger to 'try recovery
again'.

This will allow RAID10 to get the control that it needs.
Signed-off-by: NNeilBrown <neilb@suse.de>

There are places where sysfs links to rdev are handled
in a same way. Add the helper functions to consolidate
them.
Signed-off-by: NNamhyung Kim <namhyung@gmail.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Add bitmap support to the device-mapper specific metadata area.

This patch allows the creation of the bitmap metadata area upon
initial array creation via device-mapper.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

Add the 'sync_super' function pointer to MD array structure (struct mddev_s)

If device-mapper (dm-raid.c) is to define its own on-disk superblock and be
able to load it, there must still be a way for MD to initiate superblock
updates.  The simplest way to make this happen is to provide a pointer in
the MD array structure that can be set by device-mapper (or other module)
with a function to do this.  If the function has been set, it will be used;
otherwise, the method with be looked up via 'super_types' as usual.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

When an md device adds a request to a queue, it can call
mddev_check_plugged.
If this succeeds then we know that the md thread will be woken up
shortly, and ->plug_cnt will be non-zero until then, so some
processing can be delayed.

If it fails, then no unplug callback is expected and the make_request
function needs to do whatever is required to make the request happen.
Signed-off-by: NNeilBrown <neilb@suse.de>