This patch adds support for configuring the priority to
traffic class mapping.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need SFP+ plugable support for X540 hardware (copper only) so
don't enable the SFP+ interrupts.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The DCB CEE command set_state() will complete successfully
but is misleading because it enables IEEE mode. After
this patch the command is failed.

And IEEE PFC/ETS is managed from ieee paths now instead
of using CEE primitives.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the PCI device flag indicating if a VF is assigned to a guest VM
to guard against destroying VFs upon driver removal.  Implement
additional feature to detect if VFs already exist when the driver
is loaded and if so configure them and set the driver state to
SR-IOV enabled.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the IC+ IP101A Single port 10/100 PHY
and supports the APS (i.e. power saving mode while link is down)
for both IP1001 and IP101A (where this mode is supported).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o A performance drop was seen with firmware loaded
from flash. This workaround fixes it.
o Updated driver version to 4.0.77
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Set vlan header length to zero.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d1b08284 use new frag API but would leave f to be used
uninitialized, this patch fix it.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using the multi_tx_table to map possible Tx queues to Tx rings
we can just do simple subtraction for the unlikely event that the Tx queue
provided exceeds the number of Tx rings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since igb only uses advanced descriptors we might as well just use an IGB
specific define and drop the _ADV suffix for the descriptor declarations.
In addition this can be further reduced by assuming that it will be working
on pointers since that is normally how the Tx descriptors are handled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Many of the function names in the hot path are carrying an extra "_adv"
suffix on the end of them to represent the fact that they are using
advanced descriptors instead of legacy descriptors.  However since all igb
uses are advanced descriptors adding the extra suffix doesn't really add
any additional data.  Since this is the case it is easiest to just drop the
suffix and save us from having to store the extra characters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to be a general cleanup and performance improvement
for clean_rx_irq.  The previous patch should have updated the allocation so
that the rings can be treated as read-only within the clean_rx_irq
function.  In addition I am re-ordering the operations such that several
goals are accomplished including reducing the overhead for packet
accounting, reducing the number of items on the stack, and improving
overall performance.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to improve performance by splitting the Tx and Rx
rings into 3 sections.  The first is primarily a read only section
containing basic things like the indexes, a pointer to the dev and netdev
structures, and basic information.  The second section contains the stats
and next_to_use and next_to_clean values.  The third section is primarily
unused values that can just be placed at the end of the ring and are not
used in the hot path.

The adapter structure has several sections that are read in the hot path.
In order to improve performance there I am combining the frequent read
hot path items into a single cache line.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to streamline the Rx buffer allocation and cleanup.
This is accomplished by reducing the number of writes by only having the Rx
descriptor ring written by software during allocation, and it will only be
read during cleanup.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change removes support for single buffer mode from igb and makes the
driver function in packet split always.  The advantage to doing this is
that we can reduce total memory allocation overhead significantly as we
will only need to allocate one 1K slab per packet and then make use of a
reusable half page instead of allocating a 2K slab per packet.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch modifies the max_frame_size in order account for an optional
VLAN tag.  In order to support this we must also increase the
MAX_STD_JUMBO_FRAME_SIZE to account for the 4 extra bytes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up the RXDCTL and TXDCTL configurations and optimizes RX
performance by allowing back write-backs on all hardware other than 82576.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change details:
 - In a continuous sequence of ifconfig up/down operations, there is a small
   window of race between bnad_set_rx_mode() and bnad_cleanup_rx() while the
   former tries to access rx_info->rx & the latter sets it to NULL. This race
   could lead to bna_rx_mode_set() being called with a NULL (rx_info->rx)
   pointer and a crash.
 - Hold bnad->bna_lock while setting / unsetting rx_info->rx in bnad_setup_rx()
   & bnad_cleanup_rx(), thereby eliminating the race described above.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Rx queue size is changed, queues are torn down and setup with the new queue
size. During this operation, clear promiscuous mode and restore the original
VLAN filter.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a BUG_ON() as it is not required.

Change the unconditional write to release a semaphore to read sem first
and then write. This will eliminate the possibility of sem getting locked
while trying to release it in case if previous sem_get operation failed.
Signed-off-by: NGurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_tx_start_all_queues() is already called in ixgbe_up_complete, no need
to do it twice.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove duplicate inc of hwstats->ruc
Introduce separate loops for 8 and 16 register reads.
Consolidate mac checks under one case.
Make sure registers are cleared on read.
Reported-by: NJonathan Lynch <jonathan.lynch@thenowfactory.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
CC: Jonathan Lynch <jonathan.lynch@thenowfactory.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch improves the memory utilization with RSC when in one-buffer
mode.  This is accomplished by making the default buffer sizes match up
with the standard memory allocation sizes minus 1K for shared info and
padding overhead.  By doing this CPU utilization when doing large receives
can be reduced by as much as 8%.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The adapter structure was removed from the call so it can be dropped from
the ixgbe_fso documentation.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

One of the 82598 phys was not being correctly identified as being SFP.
This change corrects that.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds a small bit of missing code for enabling the overheat sensor
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_up and ixgbe_up_complete will always return 0.  Since this doesn't
provide any useful information we might as well just make them both void
and save ourselves from having to return an unused value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes an issue in which the incorrect amount of headroom was
being reserved for flow director filters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes a minor redundancy in that tx_sample_rate was set twice.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM.
Removing this needs deeper surgery.

Things noticed:
 - ixgb has RX csum disabled by default
 - HW VLAN acceleration probably can be toggled, but it's left as is
 - the resets on RX csum offload change can probably be avoided
 - there is A LOT of copy-and-pasted code here
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A user-space process must use ETHTOOL_GRXCLSRLCNT to find the number
of classification rules, then allocate a buffer of the right size,
then use ETHTOOL_GRXCLSRLALL to fill the buffer.  If some other
process inserts or deletes a rule between those two operations,
the user buffer might turn out to be the wrong size.

If it's too small, the return value will be -EMSGSIZE.  But if it's
too large, there is no indication of this.  Fix this by updating
the rule_cnt field on return.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.

Add note that drivers must not use ethtool_rxnfc::rule_locs.

The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All tables of function pointers should be const.
The pre-existing code has lots of needless indirection...

Inspired by similar change in PAX.
Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To prevent malicious usage, all tables of pointers must be const.

Compile tested only.
Gleaned for PAX.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function tables need to be const to prevent malicious use.

This is compile tested only.
Gleaned from PAX.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is compile tested only.
Suggested by dumpster diving in PAX.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An earlier developer misunderstood the meaning of the 'irq' fields and
the driver did not support the standard fields.  To avoid invalidating
existing user documentation, we report and accept changes through
either the standard or 'irq' fields.  If both are changed at the same
time, we prefer the standard field.

Also explain why we don't currently use the 'max_frames' fields.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a range check, and move the check that RX and TX are consistent
from efx_ethtool_set_coalesce().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reported TX IRQ moderation is generated in a completely crazy way.
Make it simple and correct.

When channels are shared between RX and TX, TX IRQ moderation must be
the same as RX IRQ moderation, but must be specified as 0!  Allow it
to be either specified as the same, or left at its previous value
in which case it will be quietly overridden.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>