This patch adds support for displaying PCIe Gen3 link speed, which was
previously missing from the driver.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The check for PAGE_SIZE is pointless now that the default configuration is to
allocate 32K for all buffers.  Since the Tx descriptor limit is 16K we can
just drop the check and always compare the descriptors to the maximum size
supported.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make the calculation of eerd consistent between the read and write functions
by using | instead of + for IXGBE_EEPROM_RW_REG_START
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were incorrectly checking the entire frag_off field when we only wanted the
fragment offset.  As a result we were not pulling in TCP headers when the DNF
flag was set.

To correct that we will now check for frag off using the IP_OFFSET mask.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Patrick McHardy says:

====================
The following patchset adds support for running TIPC over InfiniBand.
The patchset consists of three parts (+ a minor fix for the ethernet media
type):

- Preparation: removal of an the unused str2addr callback and move of the
  bcast_addr from struct tipc_media to struct tipc_bearer. This is necessary
  because InfiniBand doesn't have a fixed broadcast address like ethernet,
  so it needs to be initialized with the device's broadcast address when
  the bearer is enabled

- Introduction of a TIPC InfiniBand media type. A new media type is needed
  to deal with the different address sizes

- Support for ETH_P_TIPC in IPoIB

Since the last posting I've addressed all feedback I received and rebased
to the current net-next tree.

I consider these patches ready for merging. Since they mainly affect TIPC
code, I'd propose to have them either go through the TIPC tree or through
Dave directly (not sure how TIPC patches are managed).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support TIPC in the IPoIB driver. Since IPoIB now keeps track of its own
neighbour entries and doesn't require the packet to have a dst_entry
anymore, the only necessary changes are to:

- not drop multicast TIPC packets because of the unknown ethernet type
- handle unicast TIPC packets similar to IPv4/IPv6 unicast packets

in ipoib_start_xmit().

An alternative would be to remove all ethertype limitations since they're
not necessary anymore, all TIPC needs to know about is ARP and RARP since
it wants to always perform "path find", even if a path is already known.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add InfiniBand media type based on the ethernet media type.

The only real difference is that in case of InfiniBand, we need the entire
20 bytes of space reserved for media addresses, so the TIPC media type ID is
not explicitly stored in the packet payload.

Sample output of tipc-config:

# tipc-config -v -addr -netid -nt=all -p -m -b -n -ls

node address: <10.1.4>
current network id: 4711
Type       Lower      Upper      Port Identity              Publication Scope
0          167776257  167776257  <10.1.1:1855512577>        1855512578  cluster
           167776260  167776260  <10.1.4:1216454657>        1216454658  zone
1          1          1          <10.1.4:1216479235>        1216479236  node
Ports:
1216479235: bound to {1,1}
1216454657: bound to {0,167776260}
Media:
eth
ib
Bearers:
ib:ib0
Nodes known:
<10.1.1>: up
Link <broadcast-link>
  Window:20 packets
  RX packets:0 fragments:0/0 bundles:0/0
  TX packets:0 fragments:0/0 bundles:0/0
  RX naks:0 defs:0 dups:0
  TX naks:0 acks:0 dups:0
  Congestion bearer:0 link:0  Send queue max:0 avg:0

Link <10.1.4:ib0-10.1.1:ib0>
  ACTIVE  MTU:2044  Priority:10  Tolerance:1500 ms  Window:50 packets
  RX packets:80 fragments:0/0 bundles:0/0
  TX packets:40 fragments:0/0 bundles:0/0
  TX profile sample:22 packets  average:54 octets
  0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0%
  RX states:410 probes:213 naks:0 defs:0 dups:0
  TX states:410 probes:197 naks:0 acks:0 dups:0
  Congestion bearer:0 link:0  Send queue max:1 avg:0
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb->protocol field is used by packet classifiers and for AF_PACKET
cooked format, TIPC needs to set it properly.

Fixes packet classification and ethertype of 0x0000 in cooked captures:

Out 20:c9:d0:43:12:d9 ethertype Unknown (0x0000), length 56:
	0x0000:  5b50 0028 0000 30d4 0100 1000 0100 1001  [P.(..0.........
	0x0010:  0000 03e8 0000 0001 20c9 d043 12d9 0000  ...........C....
	0x0020:  0000 0000 0000 0000                      ........
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some network protocols, like InfiniBand, don't have a fixed broadcast
address but one that depends on the configuration. Move the bcast_addr
to struct tipc_bearer and initialize it with the broadcast address of
the network device when the bearer is enabled.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove warning introduced by commit 418fc57a ("usbnet: cdc-ether: apply
usbnet_link_change"):

   CHECK   .../drivers/net/usb/cdc_ether.c
 .../drivers/net/usb/cdc_ether.c:409:46: warning: incorrect type in argument 2 (different base types)
 .../drivers/net/usb/cdc_ether.c:409:46:    expected bool [unsigned] [usertype] <noident>
 .../drivers/net/usb/cdc_ether.c:409:46:    got restricted __le16 [usertype] wValue

Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The structure sctp_ulpq is embedded into sctp_association and never
separately allocated, also ulpq->malloced is always 0, so that
kfree() is never called. Therefore, remove this code.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sctp_bind_addr structure has a 'malloced' member that is
always set to 0, thus in sctp_bind_addr_free() the kfree()
part can never be called. This part is embedded into
sctp_ep_common anyway and never alloced.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_transport's member 'malloced' is set to 1, never evaluated
and the structure is kfreed anyway. So just remove it.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just a minor edit to simplify the function. No need for this
error variable here.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_outq is embedded into sctp_association, and thus never
kmalloced in any way. Also, malloced is always 0, thus kfree()
is never called. Therefore, remove that dead piece of code.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_inq is never kmalloced, since it's integrated into sctp_ep_common
and only initialized from eps and assocs. Therefore, remove the dead
code from there.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp_ssnmap_init() can only be called from sctp_ssnmap_new()
where malloced is always set to 1. Thus, when we call
sctp_ssnmap_free() the test for map->malloced evaluates always
to true.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jesse Gross says:

====================
A number of improvements for net-next/3.10.

Highlights include:

 * Properly exposing linux/openvswitch.h to userspace after the uapi
   changes.

 * Simplification of locking. It immediately makes things simpler to
   reason about and avoids holding RTNL mutex for longer than
   necessary. In the near future it will also enable tunnel
   registration and more fine-grained locking.

 * Miscellaneous cleanups and simplifications.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 7b7a2bbb (atl1: Remove unneeded PM_OPS definitions) removed the
definition of atl1_suspend for the !CONFIG_PM_SLEEP case.

So only call atl1_suspend() when CONFIG_PM_SLEEP is defined and fix the
following build error from randconfig:

drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_shutdown':
drivers/net/ethernet/atheros/atlx/atl1.c:2888:2: error: implicit declaration of function 'atl1_suspend' [-Werror=implicit-function-declaration]
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this is a pull-request for net-next/master. It consists of a patch by
Oliver Hartkopp. In this patch he cleans up the sja1000 header file by
using a common prefix for all sja1000 defines.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using SIMPLE_DEV_PM_OPS can make the code smaller and simpler.

Also change CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we can't _up() after changing the MTU, report the actual error instead
of -ENOMEM. It can be really misleading cause pch_gbe is usually used in
scenarios where the memory amount is really small, and thus hiding the
real cause.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows setting VXLAN destination to unicast address.
It allows that VXLAN can be used as peer-to-peer tunnel without
multicast.

v4: generalize struct vxlan_dev, "gaddr" is replaced with vxlan_rdst.
    "GROUP" attribute is replaced with "REMOTE".
    they are based by David Stevens's comments.

v3: move a new attribute REMOTE into the last of an enum list
    based by Stephen Hemminger's comments.

v2: use a new attribute REMOTE instead of GROUP based by
    Cong Wang's comments.
Signed-off-by: NAtzm Watanabe <atzm@stratosphere.co.jp>
Acked-by: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to add a dozen unions each time at the start
of the function. So, do this once and use it instead. Thus, we
can remove some duplicate code and make it more readable.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp: Add buffer utilization fields to /proc/net/sctp/assocs

This patch adds the following fields to /proc/net/sctp/assocs output:

	- sk->sk_wmem_alloc as "wmema"	(transmit queue bytes committed)
	- sk->sk_wmem_queued as "wmemq"	(persistent queue size)
	- sk->sk_sndbuf as "sndbuf"	(size of send buffer in bytes)
	- sk->sk_rcvbuf as "rcvbuf"	(size of receive buffer in bytes)

When small DATA chunks containing 136 bytes data are sent the TX_QUEUE
(assoc->sndbuf_used) reaches a maximum of 40.9% of sk_sndbuf value when
peer.rwnd = 0. This was diagnosed from sk_wmem_alloc value reaching maximum
value of sk_sndbuf.

TX_QUEUE (assoc->sndbuf_used), sk_wmem_alloc and sk_wmem_queued values are
incremented in sctp_set_owner_w() for outgoing data chunks. Having access to
the above values in /proc/net/sctp/assocs will provide a better understanding
of SCTP buffer management.

With patch applied, example output when peer.rwnd = 0

where:
    ASSOC ffff880132298000 is sender
          ffff880125343000 is receiver

 ASSOC           SOCK            STY SST ST  HBKT ASSOC-ID TX_QUEUE RX_QUEUE \
ffff880132298000 ffff880124a0a0c0 2   1   3  29325    1      214656        0 \
ffff880125343000 ffff8801237d7700 2   1   3  36210    2           0   524520 \

UID   INODE LPORT  RPORT LADDRS <-> RADDRS       HBINT   INS  OUTS \
  0   25108 3455   3456  *10.4.8.3 <-> *10.5.8.3  7500     2     2 \
  0   27819 3456   3455  *10.5.8.3 <-> *10.4.8.3  7500     2     2 \

MAXRT T1X T2X RTXC   wmema   wmemq  sndbuf  rcvbuf
    4   0   0   72  525633  440320  524288  524288
    4   0   0    0       1       0  524288  524288
Signed-off-by: NDilip Daya <dilip.daya@hp.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the work has been scheduled from interrupt, and not been
cancelled when the driver is unloaded, which doesn't remove
the work item from the global workqueue. call the
cancel_work_sync when the driver is removed (rmmod'ed).

Cc: Sriram <srk@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Vinay Hegde <vinay.hegde@ti.com>
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update debugging messages to a more current style.

Emit these debugging messages at KERN_DEBUG instead
of KERN_DEFAULT.

Add and use neigh_dbg(level, fmt, ...) macro
Add dynamic_debug capability via pr_debug
Convert embedded function names to "%s: ", __func__
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implemented separate irq handling for edge and level type interrupt
configuration. For edge type interrupts calls to disable_irq_nosync()
and enable_irq() are removed. The at86rf230 resets the irq line only
after the irq status register is read. Disabling the irq can lock the
driver in situations where a irq is set by the radio while the driver
is still reading the frame buffer.

With irq_type configuration set to 0 the original behavior is
preserverd.

Additional the irq filter register is set to filter out all unused
interrupts and the irq status register is read in the probe
function to clear the irq line.
Signed-off-by: NSascha Herrmann <sascha@ps.nvbi.de>

Conflicts:
	drivers/net/ieee802154/at86rf230.c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.
Signed-off-by: NSascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a follow up patch to:

    f901b6bc can: sja1000: fix define conflict on SH

That patch fixed a define conflict between the SH architecture and the sja1000
driver, by addind a prefix to one macro only. This patch consistently renames
the prefix of the SJA1000 controller registers from "REG_" to "SJA1000_".
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Rather than defining ovs specific stats struct (vport_percpu_stats),
we can use existing pcpu_tstats to achieve exactly same functionality.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Currently OVS uses combination of genl and rtnl lock to protect
datapath state.  This was done due to networking stack locking.
But this has complicated locking and there are few lock ordering
issues with new tunneling protocols.
Following patch simplifies locking by introducing new ovs mutex
and now this lock is used to protect entire ovs state.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Vlad Yasevich says:

====================
Current dev_[uc|mc]_addr_sync() API currently correctly syncs the
addresses to the first device.  Any subsequent calls to sync will
not do anything since the synched variable will be set.  This
variable is used as an optimization to skip over addresses that have
been synched.

There are some devices (ex: team) that attempt to do the above.  There
is other work in progress that needs to above to work corretly.

The short series introduces dev_[uc|mc]_addr_synch_multiple() that
allows multiple calls to sync to multiple different devices.  Original
API is left alone and still has the limitation.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Team drivers attempts to sync addresses to each of the port
devices; however, the current api doesn't really perform the sync
for any device after the first one.  Switch to using the new api
that will actually sync the addresses to all ports.

CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>