Replacing mistyped "buad" with "baud" where applicable.
Signed-off-by: NHorst Schirmeier <horst@schirmeier.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

On the ixp23xx, the microengine thread interrupt sources are numbered
56..119, but their mask/status bits are located in bit positions 64..127
in the various registers in the interrupt controller (bit positions
56..63 are unused.)

We don't deal with this, so currently, when asked to enable IRQ 64, we
will enable IRQ 56 instead.

The only interrupts >= 64 are the thread interrupt sources, and there
are no in-tree users of those yet, so this is fortunately not a big
problem, but this needs fixing anyway.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NJoshua Kinard <kumba@gentoo.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
This is known to be working fine for a while.  While at it also update
and fix the help texts.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

A proper fix would involve introducing the notion of shared caches but
at this stage of 2.6.17 that's going to be too intrusive and not needed
for current hardware; aside I think some discussion will be needed.

So for now on the affected SMP configurations which happen to suffer from
cache aliases we make use of the fact that a single cache will be shared
by all processors.  This solves the deadlock issue and will improve
performance by getting rid of the smp_call_function overhead.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
The "system type" Kconfig options on MIPS are not consistent.  For
some platforms, only the name is listed while other entries are
prepended with "Support for".  Remove this as it doesn't make sense
when describing the "system type".
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
When debugging a kernel compiled by gcc 4.1 with gdb 6.4, gdb could
not show filename, linenumber, etc.  It seems fixed if I used generic
DWARF_DEBUG macro.  Although gcc 3.x seems work without this change,
it would be better to use the generic macro unless there were
something MIPS specific.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Fix a calculation of saved vector address in trap_low.
    
(damage done by lmo f4c72cc7)
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Rename the 64-bit sc_hi and sc_lo arrays to use the same names
as the 32-bit struct sigcontext (sc_mdhi, sc_hi1, et cetera).
Signed-off-by: NDaniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
SETNAME only had a minor defect but probably never had a user and
MIPS_RDNVRAM was unimplemented anyway.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Nothing exciting; Linux just didn't know it yet so this is most adding
a value to a case statement.
Signed-off-by: NChris Dearman <chris@mips.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
The 34K is very much like a 24K on steroids.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
common/au1000/irq.c was missing a mips_timer_interrupt() prototype,
whereas in common/au1000/time.c the actual mips_timer_interrupt()
implementation was missing an irq_exit() invocation, causing a
preempt_count() leak.
Signed-off-by: NHerbert Valerio Riedel <hvr@hvrlab.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Found by Chris Dearman (chris@mips.com).
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The ARM Architecture Reference Manual lists bit 4 of the PMD as "implementation
defined" and it must be set to zero on Intel XScale CPUs or the cache does
not behave properly. Found by Mike Rapoport while debugging a flash issue
on the PXA255:

	http://marc.10east.com/?l=linux-arm-kernel&m=114845287600782&w=1Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Prevent calling of some platform functions on the clock chips of the eMac
as it seems to cause it to lockup at boot.  For now, add a quirk to prevent
that from happening.  Later, I might find out what's wrong and fix it but
that doesn't seem to be important as the machine appear to work fine
without running those.  It's possible that Darwin doesn't run them.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nathan Pilatzke <nathanpilatzke@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Uses of smp_processor_id() get pushed earlier and earlier in
the start_kernel() sequence.  So just get it working before
we call start_kernel() to avoid all possible problems.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't enable the BTB on the ixp2350 as that can cause weird
crashes (erratum #42.)  However, some bootloaders enable the BTB,
which means that we have to disable the BTB explicitly.

Found thanks to Tom Rini.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This reverts commit 5491d0f3.

As per Andi:

  "After some discussion with people who have the affected system it
   seems best to revert for 2.6.17.  It broke a common BIOS workaround
   and PCI-X still doesn't work.  Alternative is for people to change
   the BIOS which seems to be better right now."
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

int_ret_from_syscall already does syscall exit tracing, so
no need to do it again in the caller.

This caused problems for UML and some other special programs doing
syscall interception.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: Robert Hentosh <robert_hentosh@dell.com>

Actually, we just stumbled on a different bug found in find_e820_area() in
e820.c.  The following code does not handle the edge condition correctly:

   while (bad_addr(&addr, size) && addr+size < ei->addr + ei->size)
       ;
   last = addr + size;
   if ( last > ei->addr + ei->size )
       continue;

The second statement in the while loop needs to be a <= b so that it is the
logical negavite of the if (a > b) outside it. It needs to read:

   while (bad_addr(&addr, size) && addr+size <= ei->addr + ei->size)
       ;

In the case that failed bad_addr was returning an address that is exactly size
bellow the end of the e820 range.

AK: Again together with the earlier avoid edma fix this fixes
boot on a Dell PE6850/16GB
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: Daniel Yeisley <dan.yeisley@unisys.com>

It is possible to boot a Unisys ES7000 with CPUs from multiple cells, and not
also include the memory from those cells.  This can create a scenario where
node 0 has cpus, but no associated memory.  The system will boot fine in a
configuration where node 0 has memory, but nodes 2 and 3 do not.

[AK: I rechecked the code and generic code seems to indeed handle that already.
Dan's original patch had a change for mm/slab.c that seems to be already in now.]
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: "Jan Beulich" <jbeulich@novell.com>

The PM timer code updates vxtime.last_tsc, but this update was done
incorrectly in two ways:
- offset_delay being in microseconds requires multiplying with cpu_mhz
  rather than cpu_khz
- the multiplication of offset_delay and cpu_khz (both being 32-bit
  values) on most current CPUs would overflow (observed value of the
  delay was approximately 4000us, yielding an overflow for frequencies
  starting a little above 1GHz)
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: "Jan Beulich" <jbeulich@novell.com>

When using apic= on the kernel command line, this had no effect for machines
matched by either the ACPI MADT or the MPS OEM table scan. However, when such
option is specified, it should also take effect for this set of systems.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Complaining about the IOMMU not compiled in doesn't make sense
here because it is clearly compiled in.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ia32_setup_arg_pages would ignore the passed in random stack top
and use its own static value.

Now it uses the 8bit of randomness native i386 would use too.

This indirectly fixes mmap randomization for 32bit processes too,
which depends on the stack randomization.

Should also give slightly better virtual cache colouring and
possibly better performance with HyperThreading.
Signed-off-by: NAndi Kleen <ak@suse.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A typo crept in with commit ea1e847c
which defined TI_LOCAL_FLAGS to be the offset of the `flags' field
of struct thread_info, rather than the `local_flags' field.  This
fixes it.  The typo was pointed out by Guennadi Liakhovetski.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

For a very long time, echoing 'standby' or 'mem' into /sys/power/state has
killed the machine on powerpc.  This patch fixes that.

This patch adds the .valid callback to pm_ops on PowerMac so that only the
suspend to disk state can be entered.  Note that just returning 0 would
suffice since the upper layers don't pass PM_SUSPEND_DISK down, but we
handle it there regardless just in case that changes.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NJens Axboe <axboe@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Due to a firmware device tree bug, RTC and NVRAM accesses (including
halt/reboot) on Maple have been broken since January, when an untested
build fix went in. This code patches the device tree in Linux.
Signed-off-by: NHollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: NSegher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes various odd things that missed update together with cpm_uart
platform_device move. Unified resources names, restructurisation, etc.
Also, addressed issue with recent phys/virt translation rework. Being
cache-coherent, CPM2's do alloc_bootmem() for the console stuff, and it was
used to treat console buffer descriptor mapping 1:1 (as in CPM1 case),
which is definitely wrong.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add missing parentheses for type cast to u64.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NPaul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NPaul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Syscall number 224 was absent from the table, which I believe means that
the SPU can cause an oops by attempting to use it.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NPaul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Writing cr0 to cr2 register can't be right.  This fixes the typo.  I wonder
how it could survive so long.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Using asm-generic/dma-mapping.h does not work because pushing
the call down to pci_alloc_coherent() causes the gfp_t argument
of dma_alloc_coherent() to be ignored.

Fix this by implementing things directly, and adding a gfp_t
argument we can use in the internal call down to the PCI DMA
implementation of pci_alloc_coherent().

This fixes massive memory corruption when using the sound driver
layer, which passes things like __GFP_COMP down into these
routines and (correctly) expects that to work.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 32 bit unsigned substraction (next - jiffies) in stop_hz_timer can
overflow if jiffies gets advanced between next_timer_interrupt and the read
under the xtime lock.  The cast to a u64 then results in a large value
which causes the cpu to wait too long.  Fix this by casting next and
jiffies independently to u64 before subtracting them.

(Spotted by Zachary Amsden <zach@vmware.com>)
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>