The beacon early termination is not relevant for
high basic rates, which doesn't contribute
anything to the PS and only adds unnecessary FW
work.

Enable BET only if the basic rate is less than 9
Mbps.
Signed-off-by: NZiv Riesel <zivriesel@ti.com>
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Wrong fm_coex parameters were set during wl18xx
init phase, fix it.
Signed-off-by: NZiv Riesel <zivriesel@ti.com>
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Wrong fm_coex parameters were set during wl12xx
init phase, fix it.
Signed-off-by: NZiv Riesel <zivriesel@ti.com>
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This BUG_ON also ignored the INTENDED_FW_RECOVERY flag. This would
result in a BUG() when using the bug_on_recovery module parameter during
multi-role.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In some cases, the ROC_COMPLETE event might exceed the
current timeout (750 msec). Increase it to 1 sec.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

On CHANGE_CHANNEL indication, we should flush all the
queued tx frames, so they will be sent on the correct
(current) channel.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In the enum conf_tx_ac CONF_TX_AC_ANY_TID should
be 0xff to match the firmware's implementation.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The polarity should be set before the firmware is loaded
since the firmware touches the same register. Access
of the firmware and driver to the same register will
cause a collision since there is no exclusion scheme.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In ieee80211.h the uapsd bit mask is defined such that
VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3).
The firmware uses the indexing as defined in the ieee80211
spec, meaning that VO=3, VI=2, BK=1, BE=0.

In AP mode when adding peer wlcore needs to convert
the indexing accordingly.
Signed-off-by: NYoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Save the ht_cap IE per-band, so we can configure different
params to BG and A bands (we currently don't support MIMO
on A band)

[Small fix for rx_highest - Arik]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add a dependency on mac80211 in Kconfig, and also replace some spaces
with tabs.
Reported-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

With the new FW (sigle role X.3.8.0.108, multi role X.5.4.0.21)
we are supporting 3 RX BA sessions, this change is to support this
new ability.
Signed-off-by: NAssaf Azulay <assaf@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Modify default parameters to reduce firmware BSS lose
probability in congested environment.

[Applied to 18xx configuration as well - Arik]
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Make sure the deauth bcast gets sent

[Make sure we are AP as well before the flush - Arik]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Multicast management frames (e.g. global deauth)
should be sent out on the bcast link, rather than
the global, which should be used only for pre-added
stations (e.g. for auth/assoc resp).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We can't use cancel_delayed_work_sync() from functions that take the
wl->mutex, since connection_loss_work also takes the mutex. This might
result in a deadlock. Restructure the code so the work is synchronously
canceled before taking the mutex.
Avoid a bug where we would indefinitely delay the connection loss
indication by re-queuing the connection loss work on consecutive beacon
loss events.

Cc: bartosz.markowski <bartosz.markowski@tieto.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In patch d7b63b9f we have raised the dynamic
PS timeout to 200ms to improve user experience. Re-apply the change,
since it was reverted in the wlcore split.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The dynamic PS timeout is meaningless in forced PS mode.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The "static" modifier was mistakenly forgotten for some functions.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Commit 4afc37 (wlcore: reorder identify_chip and get_hw_info) broke
support for wl127x chips.

When we moved the identify_chip operation to an earlier stage (ie. to
the probe function), we broke wl127x support because during HW init we
would set the WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN.

To avoid this, set this quirk in the identify_chip operations and only
force it to be unset if the bus module doesn't support it.  We were
doing the opposite and setting the flag if the bus module supports it.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

as tcp check sum is going to be removed from firmware, and as
there is a problem with getting dns in security when checksum is
enabled, it was decided to disable it by default.
for none security modes it can be enabled by module paramenter.
Signed-off-by: NAssaf Azulay <assaf@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Some of the structures were updated, other structures had a few
missing values and a few new ones were added.  Change the driver
structs accordingly.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Now the firmware can support TX block ack sessions with 64 frames.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

With 4 pages (16Kb), we can't fit 10 frames in the aggregation buffer
during iperf.  This is the optimal for the firmware.  Thus, increase
the buffer size by one page.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Instead of adding more files from the lower drivers into the same
directory in debugfs as wlcore, we now add a subdirectory for the
lower driver.  This makes things a bit easier, because we can quickly
see where the debugfs entry is implemented and what is specific to the
lower driver.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Yet another temporary module parameter requested by the firmware team.
This will be replaced by the conf binary.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

We use hardcoded values for the different board types.  In some cases
we may need to override the defaults, so export the values as module
params.  If not defined, the defaults for the specified board type
will be used.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

With more recent PHY firmware versions (>8.1.0.0.116), we need to use
the correct value for the pwr_limit_reference_11_abg parameter when
setting the mac_and_phy options.

For now we use a hardcoded 0xc8 as the value.  This will be moved to
the configuration binary when it gets implemented.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

In some cases it may be useful to force narrow-band SISO channels.
Add a new value to the ht_mode module parameter to force the device to
operate in SISO 20MHz.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

We were setting all the rates bits when starting the AP role.  Instead
of doing this, we should set only the rates we really support
(eg. MIMO rates or wide-channel rates).  This commit changes that so
that we always use the default rates (basic rates + MCS0-7) and add
the values returned by the ap_get_mimo_wide_rate_mask operation.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

If the wl18xx module is loaded with ht_mode=wide (the default), we
shouldn't use MIMO rates when the channel type is not HT40.  Fix this
by checking the ht_mode before deciding which rates to used.
Additionally, set the ht_mode parameter explicitly to "wide" as the
default.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

In some cases it may be useful for debugging to check what is the
status of the interrupt register when a hardware recovery happens.
Print the contents of REG_INTERRUPT_NO_CLEAR (aka. HINT_STS_RAW) when
recovery starts.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

The wl18xx firmware writes the PHY firmware version in the static
data.  Add an operation to parse the static data and print the PHY
firmware version when booting.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

The wl18xx firmware has more information in the static_data than
wl12xx.  To be able to parse that in an abstracted way, this patch
adds a priv area to the static data struct and an operation that
allows the lower driver to parse it if necessary.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Implement the operations that are necessary to fetch the
wl18xx-specific FW statistics and export them in debugfs.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Implement the operations that are necessary to fetch the
wl12xx-specific FW statistics.  Re-add some of the code removed from
wlcore.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Add a macro to make it easy to print arrays from the FW statistics
array in debugfs.  At the same time, increase the buffer size so
arrays fit more easily.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

The FW statistics differ from hardware to hardware.  This commit
prepares for hardware-specific implementation of the FW statistics
debugfs entries.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

Sometimes we get a BSS_CHANGED_BEACON_ENABLED event before the basic
rates have been properly set.  To avoid problems with the firmware not
expecting to receive frames at rates that are not set during
CMD_START_ROLE, we now start with all basic rates by default.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>

When the data rates change, we get BSS_CHANGED_BASIC_RATES.  At this
point, we should update all the templates to match the new rates.  We
were changing some of the templates, but the beacon and the probe
response templates were missing.

[Remove redundant min_rate variable - Arik]
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>