Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use correct I2C address for ZL10353 DVB-T demod.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Looks like it is IF route switch on IOE[0]. Set it correctly
to route signal from tuner to demod. Now it works for DVB-C too.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is ZL10353, TDA10023 and TDA18212.
Tuner is inside of Samsung DNOD44CDH086A tuner module.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

New models have new NXP TDA18212 silicon tuner.
Not tested yet due to lack of HW...
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use board ID as base value when selecting correct hardware configuration.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Print firmware version as two digit long (change from 3 to 2).
Windows app have changed that too. First byte was hard coded as 0.

Change email list address to report non-working device to current one.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It can read more than one byte from I2C bus. Allow that.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Switch from 8 bit notation to real 7 bit.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

New silicon tuner driver.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make a user visible driver version change, for the inevitable user support
questions about why newer model HVR-1600's do not work with (older
versions of) the cx18 driver.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A previous changes which added the newer model HVR-1600's and DTV support for
them, neglected to add RF analog TV for them.  Fix RF analog TV for the newer
HVR-1600's which have a worldwide analog tuner assembly with a TDA18271 tuner
and TDA8295 demodulator.

Thanks go to Jeff Campbell and Mike Bradley for reproting the problem, and
also to Mike Bradley for doing a lot of the legwork to figure out the tuner
reset GPIO line, the demodulator I2C address, and that the GPIOs have to be
reinitialized after a cardtype switch.
Reported-by: NJeff Campbell <jac1dlists@gmail.com>
Tested-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This was replaced by Micronas drxd driver
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are still lots of 80-columns warnings and a few errors
at some tables, but changing them would require more work and
with probably not much gain.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The macro is defined as:
	#define CHK_ERROR(s) if( (status = s)<0 ) break

This sucks, as makes harder to debug if something got wrong and
there are more than one level of loops. Also, violates CodingStyle.

Fixed by this simple perl script:

	while (<>) { $f.=$_; };

	$f=~ s,\n\#define CHK_ERROR[^\n]+\n,\n,;

	$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
	$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
	$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
	$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
	$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
	$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;

	$f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;,\n\1status = \2;\n\1if (status < 0)\n\1\tbreak;,g;

	print $f;

Plus a few manual adjustments
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This file is big. It has 12000+ lines! Most of the defined stuff aren't
used anyware inside the driver, so we can just remove most of the lines
and still keep everything that have any interest for the driver.

If anyone ever need the other devices, it will be stored at git logs, so
it is easy to recover.

The diff result is impressive:
 1 files changed, 1013 insertions(+), 12694 deletions(-)
 rewrite drivers/media/dvb/frontends/drxd_map_firm.h (90%)

As a sideback effect, drxd driver will likely compile faster, and
checkpatch.pl can run on this file without taking (literally) hours.

The code cleanup was done using this small script:
	$ for i in `perl -ne 'print "$1\n" if (m/define\s+([^\s+]+)/)' drxd_map_firm.h`; do if [ "`grep $i drivers/media/dvb/frontends/drxd*.[ch]`" != "" ] ; then echo $i; fi; done|sort|uniq >used_symbols
	$ grep -f used_symbols drxd_map_firm.h >defines

And then deleting the old #define lines, replacing by "defines" file content.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s/(define\s+[^\s]+)\s........../\1/
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Take a first cleanup pass over the sources to bring them closer to the
Linux coding style.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for the PCTV 330e remote control
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove the flag indicating the 330e board is not validated, based on the half
dozen users who have reported today that everything is working.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Abstract out the firmware for the drx-d so that it can be loaded by the
request_firmware() interface.

The firmware licensing permits free redistribution, and can be found here:

http://kernellabs.com/firmware/drxdSigned-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the calls necessary to use the new drx-d driver for the PCTV 330e
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Given how PCTV has multiple products with the same model name, include the
model number in the description and #define to make it a little more clear.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The em28xx bridge strobes the reset pin on the drx-d on every ts_ctrl call.
This results in the state of the chip getting out of the sync with the
state of the driver (and hence all tuning requests after the first one fail).

Make sure the drx-d is not being held in reset, but don't actually perform a
hardware reset on the chip.

The GPIO block has been split out from the other HVR-9x0 variants to reduce
the risk of regression, although in theory they would not have any issues
since none of those cases have the frontend driver managing any internal
state.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If the tuner is not actually behind an i2c gate, using the i2c gate control
function can wedge the i2c bus.  Provide the ability to control on a per-board
basis whether it should be used.

Problem was noticed on the HVR-900 R2, where it resulted in the first tuning
attempt succeeding, and then all subsequent attempts to access the xc3028
being treated as failures (including the call to sleep the tuner).
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the required board initialization required for the drx-d to work with
the 900R2.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Provide the ability for the board configuration to specify whether to insert
the RS byte into the TS interconnect to the bridge, while not required for
the ngene in fact is required for the em28xx.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the drxd to the Makefile and Kconfig
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

These are the original drx-d sources, extracted from Ralph Metzler's GPL'd
ngene driver.  No modifications/cleanup have yet been made.  In fact, no
measures have been taken to see if the code even compiles.

Signed-off-by Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The default for "verbose" is 0.  Update description to match.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

pci_setup_device() has saved the PCI revision in the pci_dev
struct since Linux 2.6.23.  Use it.

Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Brazil uses 6MHz-spaced channels. So, the nyquist filter for
DVB-C should be different, otherwise, inter-channel interference
may badly affect the device, and signal may not be properly decoded.

On my tests here, without this patch, sometimes channels are seen,
but, most of the time, PID filter returns with timeout.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix issue where firmware does not release on cold reset.
Also, default firmware never cold resets in multi tuner
environment.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A recent patch has given individual soc-camera host drivers a possibility
to calculate .sizeimage and .bytesperline pixel format fields internally,
however, some drivers relied on the core calculating these values for
them, following a default algorithm. This patch restores the default
calculation for such drivers.

Based on initial patch by Guennadi Liakhovetski, found here:

http://www.spinics.net/lists/linux-media/msg31282.html

Except that this covers try_fmt aswell.
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The v4l2_subdev_* functions are meant for older V4L2 drivers that do not use
the control framework yet. These functions should not be used by subdev_do_ioctl.

Most of those backwards compatibility functions are just stubs, but commit
87a0c94c actually changed the behavior of
v4l2_subdev_queryctrl, so calling that one from subdev_do_ioctl broke the
control enumeration in subdev nodes.

The fix is simply not to use those compatibility functions in v4l2-subdev.c.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In the IR interrupt handler of cx88-input.c there's a 32-bit multiply
overflow which causes IR pulse durations to be incorrectly calculated.

This is a regression caused by commit 2997137b.

Cc: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>