Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

noticed by Jay Fenlason
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Replace a cast with a container_of().  As long as nobody reorders the
structure elements, they do the same thing, but container_of() is more
readable.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added complete_command_orb)
Acked-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This affects of course only the "soft shutdown" case, e.g. "modprobe -r
firewire-sbp2", while it doesn't matter for hot unplug.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This currently only affects one bridge in the hardwired blacklist.
I don't own one of those, hence haven't tested it.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Use a speed probe to determine the speed over 1394b buses and of nodes
which report a link speed less than their PHY speed.

Log the effective maximum speed of newly created nodes in dmesg.

Also, read the config ROM (except bus info block) at the maximum speed
rather than S100.  This isn't a real optimization though because we
still only use quadlet read requests for the entire ROM.

The patch also adds support for S1600 and S3200, although such hardware
does not exist yet.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Also remove some errno printouts which will be shown by infrastructure
code anyway.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

cleanup after support of single-buffer requests was dropped
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>

The attribute /sys/bus/scsi/devices/*:*:*:*/ieee1394_id, as generated by
the old sbp2 driver, is typically used to create persistently named
links in /dev/disk/by-id.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The SCSI layer only passes sg requests down, so drop the
use_sg == 0, request_bufflen != 0 case.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This should be the last missing checks.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Avoids an extra allocation and simplifies lifetime rules for the scsi_host.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This patch loads fw-sbp2 if sbp2 is still in the config file. So one can
go back and forth between releases without worry about the root
filesystem drivers.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>

Existing mkinitrd scripts still have to be adapted, unless they grok
module aliases.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Drop filenames from file preamble, drop editor annotations and
use standard indent style for block comments.
Signed-off-by: NKristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (fixed typo)

Signed-off-by: NKristian Høgsberg <krh@redhat.com>

(Reverted part which moved it from eh_abort_handler to eh_host_reset_handler)
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

In some situations we can receive the ORB status write before we
have received the ORB pointer write response.  When this happens,
we assume that the fw_transaction is finished and free the ORB
struct containing the fw_transaction.

This fix make the status write logic only accept status writes
for ORBs where the initial ORB pointer write transaction finished.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Or the SAM status codes from the device sense data into the
command error code.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The mod_timer based timing out of orb was a little to agressive and
would time out legit, but long-lived scsi cmds.  Besides, the scsi
stack keeps track of this already.  Since we're only timing out
management orbs, go back to wait_for_completion_timeout.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Use PREPARE_DELAYED_WORK to just change the function pointer.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Pointed out by Pete Zaitcev.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

This lets the SCSI stack retry the command when a SCSI command is
interrupted by a FireWire bus reset.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Sometimes we reconnect too soon, sometimes too late.  Adding a retry
mechanism make the reconnect step much more robust.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

When a management ORB times out, either because the fw_transaction
times out or when we don't get the status write, we need to properly
cancel the entire operation.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Drivers such as fw-sbp2 had no way to properly cancel in-progress
transactions, which could leave a pending transaction or an unset
packet in the low-level queues after kfree'ing the containing
structure. fw_cancel_transaction() lets drivers cancel a submitted
transaction.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Copied from sbp2:
  - enable spin-up by START STOP UNIT for all devices
  - enable INQUIRY (36) workaround on demand
  - prefer READ/ WRITE (10) over (6) for all devices
  - prefer MODE SENSE (10) for MMC devices
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Definitions as per IEEE 1212 and IEEE 1394:

     Node ID: Concatenation of bus ID and local ID. 16 bits long.
      Bus ID: Identifies a particular bus within a group of buses
              interconnected by bus bridges.
    Local ID: Identifies a particular node on a bus.
      PHY ID: Local ID of IEEE 1394 nodes. 6 bits long.

Never ever use a variable called node_id for anything else than a node ID.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

There is no emulation going on here too.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Instances of struct file_operations and struct fw_card_driver can be
qualified as "const".  Ditto with struct fw_descriptor.data, struct
fw_device_id, and predefined instances of struct fw_address_region,
at least in the current implementation.

Data qualified as const is placed into the .rodata section which won't
be mixed with dirty data.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>