The noise element in the ieee80211_rx_status struct has been deprecated in
commit "mac80211: deprecate RX status noise".  Remove the usage of this
element from wl1271_rx.c to avoid warnings.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wait for the DISCONNECT_EVENT_COMPLETE_ID event after sending a disconnect
command.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Poll for join command completion instead of waiting blindly for 10 msecs.
There is a timeout of 100 msecs, if the command doesn't complete by then, we
return an error code.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the MAC address randomization from the driver. This removes
a nasty Nokia-OUI dependency from the driver.

With this patch, unless an address is explicitly configured to the driver
by the user, only a zero address will be configured, and the driver will be
unable to start.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After the busy-words, if the firmware did not complete by the end of the
first (fixed) busy-word, a flip of the CS line is required to enable clocking
out the actual read data.

This patch changes the mechanism such that the CS line is flipped after each
busyword.

Also, the busy-word mechanism is finally enabled, and the number of fixed
busywords reduced to the minimum.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a trivial memory leak in cmd_data_path.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There were wrong format specifiers in wl1271_sdio.c in some debug
outputs. This has been causing warnings on some platforms.
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch configures the wl1271 chipset clock-request line to be
driver in open-drain mode instead of push-pull.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a memory leak in the scan command handling code.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes two memory leaks in the SPI initialization code.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add reporting of the used TX rate to mac80211 in the tx_status.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up the code to convert a firmware rate class index into an index
for the rate configuration table.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When forward porting some patches to upstream, there was a mistake and the
wl1271_spi driver name remained, erroneously, as "wl1271".  This patch fixes
that.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Chipsets since revision AR5213A (0x59) have hardware counters for PHY errors
which we can read directly from the registers. Older hardware has to use the RX
descriptor status to get a count of PHY errors. This will be used in several
places in the ANI implementation, so a flag is useful.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update PHY error codes from the HAL, and keep them in statistics for debugging
via the 'frameerrors' file. This will also be used by ANI.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Let's keep MIB counter statistics in our own statistics structure and only
convert it to ieee80211_low_level_stats when needed by mac80211. Also we don't
need to read profile count registers in the MIB interrupt (they don't trigger
MIB interrupts).
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initialize noise floor variable with a default of -95. This was used
uninitialized in the signal strength (RSSI -> dBm) conversion until the first
noise floor calibration was completed.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Keep an exponentially weighted moving average of the beacon RSSI in our BSS.
It will be used by the ANI implementation.

The averaging algorithm is copied from rt2x00, Thanks :)
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's not a phy related funtion; It has more to do with the interrupt handler
and tasklet scheduling, so it belongs to base.c.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Optimize ath5k_hw_calibration_poll() since it is called on every singe
interrupt.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't need to generate a software interrupt (SWI) just to schedule a tasklet
- we can just schedule the tasklet directly.

Rename constants, names, etc to reflect the fact that we don't use SWI any more.

Also move the flag handling into the tasklet and prepare it to behave correctly
when there are multiple flags present.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove static variable ath5k_calinterval which was used as a constant. Use a
#define instead. Also we don't need ah_cal_intval.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFrans Pop <elendil@planet.nl>
Cc: libertas-dev@lists.infradead.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFrans Pop <elendil@planet.nl>
Cc: Corey Thomas <coreythomas@charter.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFrans Pop <elendil@planet.nl>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Avoid checking for specified device type to perform certain function,
switch to .cfg approach as more generic and better implementation
method.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Use spin_lock_irqsave() in interrupt handler to disable interrupts locally
and provide the spinlock on SMP. This covers both interrupt and SMP
concurrency.

With this changes, also fix the sparse warning issues.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Remove the "\n" from following module parameter description:
 - enable wifi/bluetooth co-exist
 - led mode: 0=blinking, 1=On(RF On)/Off(RF Off), (default 0)
to be consistence with the rest of iwlagn/iwlcore module parameters format.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

In stead of checking for 4965 and do KELVIN_TO_CELSIUS conversation, add
.cfg parameter for more generic approach.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

We go to great lengths to calculate this value
that is never used by mac80211. Additionally,
it is now deprecated by mac80211 and is causing
driver compilation to give warnings.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Add missing contact email address to iwl-5000.c
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

After re-structure the agn files layout and move all the
agn shared functions out from iwl-5000.c, all those functions and data
structures do not need to be declare "extern" from iwl-5000.c in
iwl-dev.h.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Move more functions only used by agn driver from iwlcore to iwlagn.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Identify the rx functions only used by agn driver and move those from
iwlcore to iwlagn.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Identify the tx functions only used by agn driver and move those from
iwlcore to iwlagn.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

agn module parameter data structure shared by all agn devices, move it
iwl-agn-lib.c file.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Each device has it own eeprom, so the tx power version could be
different, define TX_POWER_VERSION per device.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Multiple iwlagn based devices share the same common functions.
Move those functions from iwl-5000.c to iwl-agn-lib.c file.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

uCode alive for iwlagn based devices share the same functions.
Move those functions from iwl-5000.c to iwl-agn-ucode.c.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>